PUDU PW1 Smart Watch User Guide

V1.0
Quick Guide

Product Name：Pudu Watch
Model Name：PW1

Copyright © 2019

PUDU ROBOTICS

Product Overview

Thank you for choosing our product.

This product is intended to be used with Pudu Holabot and LoRa Communication Console. Lora Wristband Pager (hereinafter the “Wristband”) is the terminal that sends and receives messages between the robot and LoRa Communication Console (hereinafter the “Console”). The entire paging communication system of Holabot is built on the LoRa communication scheme that runs over an ad hoc network. The scheme works in the following way: the Wristband initiates all task requests, sends them to the Console for task assignment and decision relaying, and then transfers tasks to the robot; the robot returns the execution result to the Console and then returns the execution status to the Wristband. Therefore, for the stable operation of the paging system, it is not recommended, unless absolutely necessary, to power down or moves the gateway once configurations are completed.

We hope that Holabot will serve your needs better.

Product Features

863-870MHz, 868MHz(H8)by default
902-928MHz, 915MHz(H9)by default
917-923.5MHz, 920MHz(H9K)by default
NFC Read-Write Card| Available
LCD| 1.3-inch TFT LCD screen, RGB full color, 240 x 240 pixels
Battery Capacity| ≥ 300mAh
Theoretical Battery Life| 24H¹
Standby Current| 1.1mA
Communication Distance| ≥ 400m¹

¹ The theoretical battery life is derived in the laboratory by initiating one call every 30 minutes.
² Testing conditions: On a sunny day, in an open place, and at the maximum power, an antenna gain of 5 dBi, a height greater than 2 m, and a data rate of 2.4 Kbps.

Product Features

Note: Before installing the gateway, check all the accessories included in the package. If anything is damaged or missing, please contact your seller immediately.

Notes for Use

1. You can either wear the Wristband around your wrist or put it onto the charging dock and affix it anywhere you want the call to be initiated.
2. The Wristband is water-proof and can still work properly upon reasonable exposure to water. However, it cannot withstand any violent flushing or soaking, or provide resistance to water in a steam environment.
3. The Wristband comes with an LED indicator to indicate the Wristband’s status in different colors, i.e., calling in blue, charging in green, and low battery in red.
4. Do not use the Wristband in an environment with a temperature lower than -20°C or higher than 40°C, and protect the Wristband from any liquid ingress.
5. In some circumstances, the walls of private dining rooms may impair the Console’s ability to send and receive signals around the edges. In this case, reposition the Console to maximize its coverage. If the signal is still poor after repeated adjustments, it means this environment is beyond the coverage of the Console.

Buttons on the Wristband

Configurations

Configuring the Hardware

1. There is a disposable adhesive sheet on the bottom of the charging dock. Remove the film to expose the adhesive surface. You can stick the charging dock onto a table or a wall. When the Wristband is used as a pager, take the length of the charging cable and the position of the charging dock into consideration in the configuration.
2. Once you have configured the charging dock, simply remove the strap of the Wristband and attach it to the charging dock through the magnetic
3. When the Wristband is used as a mobile calling watch, calling cards are These cards are included with the Console, 100 cards for each Console by default.
4. For the Wristband to initiate a call upon card swiping, press the home button to the right of the screen to light up the screen, and then touch the calling card to initiate a call.

Connecting the Wristband to the System

1. Once you have got the environment ready, built the map, and added elements for Holabot, you can get started with connecting the Console.

2. Follow the Console User Manual to go through the connection steps.

3. After the connection is complete, press and hold the home button to start the Wristband and select the channel corresponding to the current

4. If the Wristband is started for the first time, you will be automatically directed to the channel selection screen. If you accidentally choose the wrong channel, you can reset the data to refresh the Wristband and open the channel selection screen again by the following operations:
   ● Press and hold the Up button for 3 seconds to go to “Settings”.
   ● Press the Down button and select “Reset Data”.
   ● Press the home button to go to the confirmation screen for data resetting.
   ● Press the Up button, select “Reset” and press the home button again to confirm the
   ● After the data is reset, the device restarts automatically and the channel selection screen appears.
   ● Use the Up and Down buttons to select a channel and press the home button to confirm your selection.
   ● After you are finished, you will be directed to the “Awaiting Broadcast from Console” screen.
   

5. On the “Call Settings” → “Pager Settings” screen of the robot, tap to refresh a random calling number, and tap to initiate a broadcast.
   

6. The “Awaiting Broadcast from Console” screen of the Wristband changes to display a message prompting you to accept the calling number. Tap “Accept” and you will see a message showing the result of the operation.
   

7. After you are finished, tap to disable the broadcast for adding pagers (VERY IMPORTANT).

8. Once the pairing is successful, the Wristband will start the map version checking process.

9. If the Wristband is added for the first time or the map has changed, a map update will be required. (It generally takes 3 to 5 minutes to update the map, depending on the area covered by the map and the number of tables.)
10. Once the map is updated, the main calling screen appears with the first table number selected by default.

Setting the Wristband Modes

1. On this screen, press and hold the Up button for 3 seconds to go to “Settings”.

2. Press the Down button to select
   “Wristband Modes” and press the home button.
   

3. Three modes are available:
   a) Pager Mode: A call can be initiated by pressing the home button but not by swiping the calling card.
   b)Dish-washing Room Mode: Once the robot arrives at the dish-washing room, the Wristband receives a message notifying that the robot has arrived. c)Lobby Mode: A call can be initiated by swiping the calling card but not by pressing the home button.
   Please select the desired mode.
   After a mode is selected, the Wristband will restart and display the home.

Setting the Calling Point

1. On this screen, press and hold the Up button for 3 seconds to go to “Settings”.

2. Select “Calling Point Settings” and press the home button.
   

3. The “Calling Point Settings” screen shows all the tables or private dining rooms that can initiate call requests within the map. Press the Up or Down button to select a table number or private room, and press the home button to confirm your selection.

4. After the selection, you will be directed back to the “Settings” screen by pressing the Up button to select the “Back” button on the “Settings” screen and press the Up button again to return to the home screen.

Adding a Calling Card

1. On the robot screen, tap “Calling Card Settings”.

2. Tap and select the number of the table or private room for which you want to add a calling card on the screen that appears. Tap OK to confirm your selection.
   

3.  Tap and the above screen appears.
   

4. Now, use the Wristband for which you have finished the map update and other configurations, take out the calling card included with the Console, light up your Wristband, and touch the front of the screen.
   

5. When a call is initiated, the Wristband vibrates and the above screen appears.
   

6.  As the card adding process gets done quickly, you will soon be directed to the “Arrived” screen.

7. The number of the calling card to add will appear on the robot screen.
   

8.  Tap Confirm to complete the process.(Note: If the card to add has been added for another table or private room, you will be prompted that the card has been added, and the operation will fail.)
   

9. Tap “Save Configurations” to save the card you have added.

Using the Wristband

Initiating a Call in Lobby Mode

1. The screen will automatically turn off when the Wristband is left idle for several seconds. Press the home button to light up the screen.

2.  Once the screen lights up, touch the calling card with the Wristband to initiate a call to the robot (A Wristband in Lobby Mode can initiate a call only by touching the calling card.)
   

3. Once the call is initiated, the task will be put into the queue. (The call result will be returned by the Console.)

4. When the robot starts to execute the task, the “Coming” screen appears.
   

5. Once the robot arrives at the destination, the screen changes to “Arrived”, which stays put for several seconds before returning back to the home screen.

6.  You can press the home button to try to cancel the call before the robot arrives.
   

7. Press the Up button to select “Yes”, and press the home button again to cancel the call.
   

Initiating a Call in Pager Mode

1.  1You can initiate calls in Pager Mode using the same steps as in Lobby Mode.
2. However, Pager Mode only allows a call to be initiated by pressing the home button.

Working in Dish-washing Room Mode

1. In Dish-washing Room Mode, the Wristband cannot initiate calls; it can only receive messages about the arrival of the robot.

2. Once the robot arrives at the dish-washing room, the Wristband receives a message notifying that the robot has arrived.
   

3. Press the home button to view the status of all tasks.

After-sales Service

1. Free Warranty
   When the robots are under warranty (different warranty periods for different components, calculated from the receipt of the robot), Pudu offers a free warranty.
   • Defects are caused by non-human factors.
   • There are no unauthorized disassembly, modification, or addition not included in the user manual, or other faults caused by non-human factors.
   • The robot S/N sticker and other labels are not removed or altered.
   • Effective purchase certificate, receipt, and order number are provided.
   • Damaged components are sent back to Pudu as required.

2. Paid Services
   Pudu offers paid after-sales services when the robot is out-of-warranty or the policy of free warranty is not applicable.
   • Online and remote technical support are provided, and customers should cooperate with engineers for diagnosis and troubleshooting.
   • Technicians will offer on-site service when necessary.
   • The “After-sales Service Form” should be filled when the policy of free warranty is not applicable; Customers should pay for both maintenance and spare parts.

3. Contact Us
   For any questions, please call +86-400-0826-660.
   Working hours: 9:30 – 12:00,13:30 – 18:30, Monday to Saturday (GMT+8)

http://www.pudutech.com/

This device complies with part 15 of the FCC Rules. Operation is subject to the condition that this device does not cause harmful interference (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•  Consult the dealer or an experienced radio/TV technician for help.

FCC ID: 2AXDW-PW1

IC Caution:

This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science, and Economic Development Canada’ s license-exempt RSS(s). Operation is subject to the following two conditions:

1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of the device.

Specific absorption rate (SAR):
This Pudu Watch meets the government’s requirements for exposure to radio waves. The guidelines are based on standards developed by independent scientific organizations through periodic and thorough evaluations of scientific studies. The standards include a margin of safety designed to ensure the safety of all people regardless of their age or health.

The FCC Statement of Exposure to RF and the SAR limit for the United States (FCC) is 1.6 W/kg average for each gram of tissue. This device was tested for typical operations of use on the body, with the back of the Watch at 10mm from the Front-of-Face and the Watch at 0mm from the Back-of-Wristbands. To maintain compliance with FCC RF exposure requirements, use the Watch at 10mm from the Front-of-Face and the Watch at 0mm from the Back-of­Wristbands. The use of belt clips, covers, and similar accessories must not contain metallic components in their assembly. The use of accessories that do not meet these requirements may not meet FCC RF exposure requirements and should be avoided.

Functioning in the body
This device was tested for typical operations of use in the body. To comply with RF exposure requirements, use the Watch at 10mm from the Front-of-Face and the Watch at 0mm from the Back-of-Wristbands, including the antenna. Third-party accessories such as belt clips. covers and similar accessories used with this device should not contain metallic components, accessories that do not meet these RF exposure requirements and should be avoided from use on the body. Use only the supplied antenna or an approved antenna.

Disclaimer

Copyright © 2019 Shenzhen Pudu Technology Co., Ltd. All rights reserved. This document may not be copied, reproduced, transcribed or translated, in part or in whole, by any persons or organizations, or be transmitted in any form or by any means (electronic, photocopy, recording, etc.) for any commercial purposes without the prior written permission of Shenzhen Pudu Technology Co., Ltd. The product specifications and information mentioned in this document are for reference only and are subject to update without prior notice. Unless otherwise specified, this document is used as a guide only and comes with no warranties of any kind.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>