WHILL Ci2 Power Chair Instruction Manual

October 27, 2023
WHILL

WHILL Ci2 Power Chair

WHILL Ci2 Power Chair

This Operating Guide is intended to provide instructions on basic usage of the device. To operate the device safely, please ensure to carefully read this guide before use. It is recommended to keep this guide on hand at all time for your reference.

Major precautions for use

The WHILL Model Ci2 is a mobility vehicle. Persons who find it difficult to use a powered wheelchair should refrain from using the device.

  • The maximum load weight for this device is 300 lb (approx. 136 kg). It includes both the occupant and any luggage. Ensure the the load weight does not exceed the maximum during use.
  • Turn off the device power when getting in and out of the device.
  • Keep your feet on the foot rest while driving to avoid feet or clothing getting caught in moving components.
  • Avoid traffic and narrow space, and follow the traffic rules to drive safely.

Dress appropriately for driving.

  • There is a risk that clothing such as long scarves, loose pants, skirts and rain coats may be caught in tires or other parts of the device, resulting in injury.
  • When wearing gloves, be careful to avoid getting them caught in the device, such as in the control components.

Drive carefully in the following areas.

WHILL Ci2 Power Chair 1

Avoid rail road crossings and take a safer route whenever possible.
If you must pass a rail road crossing, ensure you understand how to manually release the brakes (p4) and ask a caretaker to accompany you.
Do not drive the device in areas with soft surfaces such as sand, mud, snow or frozen paths. There is a risk that accidents may occur.

Basic operations

WHILL Ci2 Power Chair 2

  1. Get in the device
    Confirm the device power is off before getting into the device.

  2. Turn on the power
    Press the power button and confirm the display turns on.

  3. Set speed
    Adjust the speed setting from 1 to 4 by using speed select buttons.

  4. Move and turn around
    Move the joystick slowly in the desired direction.

  5. Stop
    Release the joystick.

  6. Turn off the power
    Press the power button and confirm the display turns off.

  7. Get out of the device
    Confirm the display is off, and then get out of the device.

Ensure to turn off the device power when getting in and out of the device.

Driving tips

  1. How to stop
    Release the joystick to stop. Releasing the joystick automatically applies the brakes and stops the device even on an uphill or downhill slope.

  2. How to hold the joystick
    Place fingers on the joystick.WHILL Ci2 Power Chair 3

  3. How to move the joystick
    Adjusting the speed The device speed can be controlled by the tilting degree of movement of the joystick.
    In the beginning, ensure to operate the joystick gently and drive slowly.

Climbing over a step
When climbing over a step, approach at a right angle to the step.

WHILL Ci2 Power Chair 4

Releasing the brakes
Certain situations may require control of the device without powering on and using the joystick—known as freewheel mode. This can be accomplished using the two red brake release levers.

Turn off the device power. Push down both of the two brake release levers below the seat.
Raise both brake release levers to re-engage the brakes afterwards.

WHILL Ci2 Power Chair 5

Do not release the brakes on a slope. Be sure to release the brakes only when on a flat surface and in emergencies after turning off the power. After moving the device manually with the brakes released, be sure to raise the two brake release levers to re-engage the brakes.

Using the smart key
The smart key can be used to lock and unlock the device.

WHILL Ci2 Power Chair 6

Press the smart key lock button.
The icon indicating the locked status will appear on the controller’ s display and make a locking sound. When attempting to turn on the device when the device is locked, the icon indicating the locked status will appear on the display. The device cannot be turned on.

WHILL Ci2 Power Chair 7

Press the smart key unlock button. The smart key LED will illuminate, and the icon indicating unlocked status will appear on the display and make a unlocking sound. The device will be unlocked.

WHILL Ci2 Power Chair 8

Sold separately. Equipped with standard items depending on the areas/countries.

Disassembly procedure
When assembling or disassembling the device, grab only the handles and parts as described in the instructions, and do not hold the device by any other areas.

This device can be disassembled into the following five components.
Remove the battery before disassembling.

WHILL Ci2 Power Chair 9

Removing the battery

WHILL Ci2 Power Chair 10

Removing the seat assembly

WHILL Ci2 Power Chair 11

  • Lift the seat assembly slowly so that it does not damage other parts.
  • When placing the seat assembly on the floor, place it with the cushion facing up.

When lifting the seat assembly, the magnetism of the magnetic connectors located at the connection between the seat assembly and rear drive base may have an adverse effect on electrical medical devices. Persons who have an implanted pacemaker, implanted defibrillator, or other electrical medical devices in their bodies, must leave a minimum of 8 inches (20 cm) between themselves and the magnetic connectors.

3. Removing the storage basket
Remove items from storage basket, then lift the storage basket straight up by holding its handles and remove it from the front drive base.

Disconnecting the front drive base

WHILL Ci2 Power Chair 12

Assembly procedure

WHILL Ci2 Power Chair 13

Installing the storage basket

WHILL Ci2 Power Chair 14

If the device does not start properly even though a charged battery is inserted to the device and the device is turned on, remove the battery, then re-insert the battery after 10 seconds.

Installing the seat assembly

WHILL Ci2 Power Chair 15

Installing the battery

WHILL Ci2 Power Chair 16

Charging the battery

  1. Charging with the battery installed in the device

  2. Move the device close to the outlet and turn off the device power.
    Connect the charger and AC connector cord.

  3. Plug the charger into the power outlet. The charger indicator illuminates red.

  4. Remove the battery charging port cap and connect the DC connector to the battery charging port. The charger indicator begins flashing green and charging starts.

  5. Charging is completed when the charger indicator turns solid green.

  6. Disconnect the DC connector from the battery, then disconnect the plug from the power outlet. Close the cap of the battery charging port.

  7. Charging with the battery removed

  8. Check the device power is off and press the battery lock release button.
    Grasp the handle and pull to remove the battery.

  9. Connect the charger and AC connector cord. Plug the charger into the power outlet.

  10. Remove the cap of the battery charging port and connect the DC connector to it.
    The charger indicator begins flashing green, and charging starts.

  11. Charging is completed when the charger indicator and battery LED turns solid green.

  12. Disconnect the DC connector from the battery, and then the plug from the power outlet.

  • Do not touch the battery and charger during charging to prevent burns.
  • Ensure charging the battery indoors.
  • The battery and charger are for the WHILL Model Ci2 only.
  • Only use the designated battery and charger for the device.

Troubleshooting

In the event of certain issues with the device, an error code will appear on the display.
If an unlisted error is displayed or the issue persists even though a problem was handled in line with troubleshooting, contact your distributor or customer support.

WHILL Ci2 Power Chair 17

When the device does not turn on, check the battery level and if it is inserted fully into the compartment. If the device does not start properly, remove the battery,
then re-insert the battery after 10 seconds and turn on the device after 5 seconds.

How to pair your smartphone app

App allows users to check total mileage, distance traveled, battery level, full charge cycles and to use the remote control function. Users can also lock and unlock the unit.

  1. You need to install the app beforehand. To install, go to the App Store and search for “WHILL”. Click the blue WHILL logo icon for the WHILL Model C2 app.
    (The grey logo icon is for WHILL Model C.)

  2. To pair your device, launch the WHILL Model C2 app and enter the following codes* on the screen.

11-digit alphanumeric code
password

The two codes are printed on the paper slip placed in the indent of the seat of the device.
Note: Depending on your region and smartphone type, the app may not be offered, or some functions may not be available.

www.whill.inc

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals