LOCKEY 7055SCP Super 8 Mechanical Digital Lock Instruction Manual

DIGITAL DOOR LOCK
W/HANDLE INSTALLATION INSTRUCTON

MECHANICAL COMBINATION ACCESS CONTROL DOOR LOCK EQUIPPED WITH DOUBLE PUSHING AND SINGLE PUSHING FUNCTION
*READ ALL THE INSTRUCTIONS BEFORE THE INSTALLATION

THE NAME AND DETAILS OF THE ENCLOSED PARTS

NO.| NAME OF PARTS|

Q

---|---|---
1.| OUTSIDE BODY| 1PcE
2.| INSIDE BODY| 1
3.| ESCUTCHEON| 2
4.| MAGNETIC MORTISE STRIKE| 1
5.| MAGNETIC LATCH BOLT UNIT (60MM BS OR 70MM BS:| 1
6.| FACEPLATE FOR latchbolt| 1
7.| SPINDLE (87MM L)| 1
8.| L SUPPORT PIN| 1
9.| MACHINE SCREW 4X6 FOR L SUPPORT PIN| 1
10.| MACHINE SCREW 4 x 55| 2PCS
11.| MACHINE SCREW 4×45| 2
12.| WOOD SCREW 4 x 16| 4
13.| KEYLESS TUMBLER(BLUE)| 1
14.| KEY TUMBLER(RED)| 1
15.| DOUBLE FUNCTION KEY TUMBLER (GREEN)| 1
16.| TWEEZERS| 1
17.| CODE NUMBER CARD| 1
18.| INSTALLATION INSTRUCTIONS| 1

BEFORE INSTALLING THE DIGITAL DOOR LOCK, “SUPER-8”

CONFIRM THE HAND OF OPENING
The lock comes factory set for right-hand opening, if your door is hinged on the right from the entry side then proceed to HOW TO INSTALL after installing the L support pin as per below. If your door is hinged on the left from the entry side then follow changing the hand of opening to the left hand.
CHANGING THE HAND OF OPENING TO LEFT HAND

• Move the screw (1) into position (2)
• Remove the two screws (3) from the inside of the handle releasing the handle cover.
• Remove the two screws (4) that connect the handle to the lock, lift the handle off and reverse it to the left hand. Replace all screws securely.
• Repeat the same with the inside handle.
• On the entry side of the lock on either side of the spindle cog, there are two holes(a,b), screw the L support pin into the following position for R/H opening and the opposite position for L/H opening.

HOW TO INSTALL THE DIGITAL DOOR LOCK, “SUPER-8”

Using the template provided on page 10 for 60m/m B.S. or 11 for 70m/m B.S., decide on the position you want your lock.

• Mark the hole centers for each of the 3 holes on the surface of the door, and for the latch bolt at the center of the door edge through the template.
• Drill the 3 holes, the upper and lower 2 holes010mm dia and 3rd larger hole @36mm dia.) the hole in the edge of the door 025mm dia for the latch bolt.

*• • •’60MM BACK sr is 85mm depth • • •
• • •’70MM BACK SET” is 95mm depth • • •
** Insert the latch bolt into the slot making sure the arrow faces upwards and scribe a line around the latch-bolt face. Remove it.
Chisel out the scribed space until the latch bolt face is flush with the surface of the door edge.
Fasten the latch bolt unit with the wood screws(4 X16), evenly.

Insert the 2 hexagonal posts into the upper and lower holes of the front body and place the escutcheon on. Position the front body onto the door.
NOTE -CONFIRM THAT THE SUPPORT PIN IS INSERTED INTO THE SUPPORT PINHOLE OF THE LATCH BOLT UNIT, SMOOTHLY.
Before closing the door test your lock from the inside and outside to ensure it is set correctly.

AFTER CONFIRMING THE ABOVE
Close the door and decide on the position whore the latch bolt head touches the face of the door jamb. And mark the hole for the mortise strike.
After that, chisel out the space for the magnetic strike box. Fasten them with the wood screws.

HOW TO USE THE DIGITAL DOOR LOCK, “SUPER-8”

1. When the door is closed, the”SUPER-8″ locks automatically.
2. From the inside, unlock using the lever handle.
3. From the outside, unlock by pressing the correct code and then using the lever handle.

‘HOLDBACK` DEVICE
The holdback holds the latch bolt head back: this is very convenient.
When using the code is not always necessary.
TO OPERATE
Pull the inside handle down until the latch bolt head retracts fully. and push the holdback down.
To restore push up the holdback.

HOW TO CHANGE THE CODE NUMBER

TO PREVENT ANY PROBLEMS OR DAMAGE, READ THE FOLLWING INSTRUCTIONS BEFORE CHANGING YOUR CODE
Hold the front lock body in the horizontal position. Remove the 4 red screws and take the lid off carefully.
THE CODE TUMBLER THE GREEN COLOURED ARE THE TUMBLERS FOR DOUBLE PUSHING’ THE RED COLOURED ARE THE TUMBLERS FOR SINGLE PUSHING’ THE BLUE COLOURED ARE KEYLESS TUMBLERS ‘NON. CODE THE PLAIN TUMBLER IS THE C BUTTON (TO CLEAR] NEVER REMOVE THIS TUMBLER
FOR EXAMPLE, THIS `CODE NUMBER’ IS MADE UP OF THE TO CLEAR THEN 22478 WHILST PUSHING IN THE C BUTTON AND USING THE TWEEZERS PROVIDED. PLACE YOUR CODE TUMBLERS INTO POSITION

HOW TO CHANGE THE CODE NUMBER

TO INCREASE AND DECREASE THE NUMBER OF DIGITS USED IN YOUR CODE ADD MORE RED AND GREEN TO INCREASE. ADD MORE BLUE TO DECREASE.
IT IS VERY IMPORTANT TO REPLACE THE CODE TUMBLERS IN THE CORRECT WAY. THE COLORED TOP END MUST ALWAYS FACE UPWARDS. AND THE SIDE OF THE TUMBLER THAT HAS THE RAISED NOTCHES MUST FACE TOWARD THE TOP OF THE LOCK REMEMBER TO KEEP THE ‘t PRESSED IN WHILE REMOVING AND REPLACING THE TUMBLERS.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>