LOCKEY USA 2900 Mechanical Keyless Narrow Stile Deadbolt Lock

The LockeyUSA 2900 Deadbolt and 2950 Hook Bolt are designed for narrow stile prep doors or replaces configurations with existing narrow stile hardware with 1 1/8” prep (Adams Rite).
Note: For 1 1/8” narrow stile prep doors, please skip to Step 2.
Before Installing: Change User Code/Combination (OPTIONAL)
To change user code/combination, see instructions below.

Installation

Step 1: Remove all previously installed hardware. Note: DO NOT discard previously installed Trim Plate (may be used).

Step 2: Using the template provided, mark mounting holes on the surface of the door.
Note: After marking mounting holes, check to ensure the drive/spindle hole is placed at the bottom. This mounting is opposite compared to most Adams Rite configurations.

Step 3: Check template to guarantee proper measurements and hole pattern. Drill holes accordingly.

Step 4: After drilling mounting holes, check to make sure that the lock and spindle/tailpiece line up with holes.

Step 5: The lock is factory pre-handed for left-hand doors.
To change handing, remove the two blue screws and cover plate from the Outside/Combination Body. Next, move the pin from the left side of the Outside Body to the hole on the right side. Replace plate and screws.
Note: For 2900 DC and 2950 DC, Inside Body handing pin must be placed on opposite side from Outside Body.

Step 6: Hold Deadbolt/Hookbolt in place with Drive/Spindle hole on bottom and secure with mounting screws.

Step 7: To Verify Correct Spindle Length, hold Inside Body to the door.
Place spindle/tailpiece through the spindle/drive hole of the Deadbolt/Hookbolt. Check to ensure that the spindle/tailpiece engages the lock.

• Spindle should extend from exterior of door 3/8” min. to 5/8” max.
• If spindle extends less than 3/8” it may not engage the lock.
• If spindle extends more than 5/8”, it will cause the lock to bind.
• If spindle is too long, cut it to the correct length using pliers.

Step 8: Place rubber escutcheon on Outside Body and place Outside Body on door.

Step 9: Place rubber escutcheon on Inside Body and secure Inside Body to the Outside Body on the door using the provided screws. After installing the lock, replace and secure face plate.

Please Note: Due to variances in face plate sizes, you may need to use the previously installed face plate.
Note: The strike may need to be modified to accommodate the 2900 Deadbolt/2950 Hookbolt.
Note: In some cases, the rubber escutcheon may need to be trimmed on the inside body to allow proper door closure.
This is due to the jamb edge on the interior of the door. In rare cases, you may also need to trim the jamb edge to accommodate the lock.

How to Change Code

1. Using a #2 screwdriver, remove the four (4) red screws.

2. Carefully remove cover plate.
WARNING: Springs are attached to plate.

• RED = CODE TUMBLERS
• BLUE = NON-CODE TUMBLERS
• ‘C’ = CLEAR (DO NOT REMOVE)

3. Press & Hold ‘C’ button to release tumblers.

IMPORTANT: ‘C’ button must be pressed and held down when removing and inserting tumblers. Failure to do so will damage the lock and void the warranty.

4. While holding the ‘C’ button, remove/add Code (Red) and Non-Code(Blue) tumblers to create your desired code.
Ex. 3 Red = 3-Digit Code/ 6 Red = 6-Digit Code
Important: Ensure notched side of tumbler fits into slot (right).

5. After changing your code, release the ‘C’ button to secure the tumblers in place.

6. Replace the cover plate and secure with four (4) red screws, using a

2 screwdriver.

7. TEST CODE before installing/re-installing your lock.

Important: FILE MAY NOT PRINT AT 100% ACCURACY. PLEASE CHECK MEASUREMENTS BEFORE DRILLING.

Documents / Resources

| LOCKEY USA 2900 Mechanical Keyless Narrow Stile Deadbolt Lock [pdf] Instruction Manual
2900 Deadbolt, 2950 Hook Bolt, 2900 Mechanical Keyless Narrow Stile Deadbolt Lock, Mechanical Keyless Narrow Stile Deadbolt Lock, Narrow Stile Deadbolt Lock, Deadbolt Lock
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>