GL iNet GL-XE3000NR Puli AX 5G NR Wi-Fi 6 Router User Guide
- June 1, 2024
- GL iNet
Table of Contents
Let’s get started.
Puli AX
5G NR Wi-Fi 6 Router (GL-XE3000NR)
SETTING UP
(1) Insert Cards & Power On
When powered up, your router will broadcast both 2.4G and 5G Wi-Fi signal with the SSID: GL-XE3000-xxx and GL-XE3000-xxx-5G.
Hot plug for TF card is not supported for this router.
After inserting cards, turn on the router by pressing the power button
(2) Connect via Wi-Fi
Connect to the Wi-Fi called GL-XE3000-xxx or GL-XE3000-xxx-5G , and then input the default Wi-Fi password which is printed on the bottom label of the router.
Search the SSID and connect to it
or
Connect via LAN
Plug the cable connecting to your computer into LAN port
(3) Set Up Router
Visit https://192.168.8.1 in your browser to set up your router; start by choosing your preferred language.
SUPPORT
- 4G/5G Antennas
- Wi-Fi Antennas
- Power port
- WAN Ethernet port
- LAN Ethernet port
- USB 2.0 port
- TF Card Slot
- Nano-SIM Card Slots
- Reset button
- Lights: Power
- Battery
- Internet
- 2G Wi-Fi
- 5G Wi-Fi
- Cellular
Repair / Reset
If you cannot access the web-based setup page or cannot connect to the router, you can press the Reset button:
- Press and hold for 3 seconds , and then release to repair your network.
- Press and hold for 10 seconds , and then release to reset the router to factory settings. All user data will be cleared.
https://docs.gl-inet.com/en/4/
Technical Supports
- For more detailed and updated instructions, please visit our website docs.gl-inet.com
- For further questions, you can get help from the following ways:
– Email to support@gl-inet.com
– Message us on our Facebook: facebook.com/gl.inet.wifi/
– Post questions in our forum: forum.gl-inet.com
– Ask professionals in other forums e.g. OpenWrt, LEDE or other professional websites
WARRANTY
- We provide one year limited warranty for routers and 3-month limited warranty for accessories. Extra warranty may apply according to the local law in which the product purchase took place.
- Highly recommend using the included 12V/2.5A power adapter.
- Any damage to the router caused by not following the instructions will render this warranty null and void.
- Any damage to the router caused by modifying the PCBA, components or case will render this warranty null and void.
- Issues caused by the use of third-party firmware may not get official support from us.
- Any damage to the router caused by inappropriate use, e.g. inappropriate voltage input, high temperature, dropping in the water or on the ground will render this warranty null and void.
- Pictures on the instructions are only for reference. We reserve the right to change or modify these materials without further notice.
Operation temperature 0 ~ 40 | Storage Temperature: -20~45 | Humidity: 5%~95%, non-condensing | Storage Humidity: 5%~95%, non-condensing
Please follow the below guidelines for daily use:
- To avoid battery or device failure, do not remove or replace the non-removable battery.
- Disposal of the device with battery into fire or a hot oven, or mechanically crushing or cutting of a battery, that can result in an explosion.
- Please don’t charge the battery if the environment exceed the device operation temperature. Leaving the device in an extremely high temperature surrounding environment that can result in an explosion or the leakage of flammable liquid or gas.
- A battery subjected to extremely low air pressure that may result in an explosion or the leakage of flammable liquid or gas.
- If the device with the battery is stored for more than 3 months, the battery needs to be charged to ensure the battery life.
- If the device is accidentally dropped on the ground, causing problems such as damage to the casing, it may also cause damage to the battery, please contact the device seller for repair or replacement in time.
- If the device is off, press the power button before charging. If the battery indicator flashes, it is safe to charge. If not, avoid charging as this may indicate a damaged battery and could pose safety risks. Should you encounter this issue, please reach out to the device’s seller for support.
FCC ID: 2AFIW-XE3000NR
1. This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference
that may cause undesired operation.
2. Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
3. Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help important
announcement.
This device contains licence-exempt transmitter(s)/receiver(s) that comply
with Innovation, Science and Economic Development Canada’s licence-exempt
RSS(s). Operation is subject to the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may
cause undesired operation of the device.
This equipment complies with FCC / IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body.
i. for devices with detachable antenna(s), the maximum antenna gain permitted
for devices in the bands 5250-5350 MHz and 5470-5725 MHz shall be such that
the equipment still complies with the e.i.r.p. limit;
ii. for devices with detachable antenna(s), the maximum antenna gain permitted
for devices in the band 5725-5850 MHz shall be such that the equipment still
complies with the e.i.r.p. limits as appropriate;
The user manual for LE-LAN devices shall contain instructions related to the
restrictions mentioned in the above sections, namely that:
i. the device for operation in the band 5150-5250 MHz is only for indoor use
to reduce the potential for harmful interference to co-channel mobile
satellite systems;
The functions of Wireless Access Systems including Radio Local Area Networks(WAS/RLANs) within the band 5150-5350 MHz for this device are restricted to indoor use only within all European Union countries.
|
AT
| BE| BG| HR| CY|
CZ
---|---|---|---|---|---|---
DK
| EE| FI| FR| DE|
EL
HU
| IS| IE| IT| LV| LI
LT| LU| MT| NO| PL|
PT
RO
| SK| SI| ES| SE| CH
NL| UK(NI)|
UK
Hereby, GL TECHNOLOGIES (HONG KONG) LIMITED declares that the radio equipment type [5G NR Wi-Fi 6 Router, GL-XE3000NR] is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: https://www.gl-inet.com/products/certificate
INSTALLATION
Adhesive Mount
(1) Peel off the matte white film and then attach the adhesive pad to the wall mount permanently.
- matte white
- Flip
(2) Peel off the glossy transparent film and then stick the adhesive pad onto a clean and dry glass surface.
Caution: Please avoid sticking the adhesive pad to rough or wet surfaces, as this could potentially result in the device falling off and sustaining damage.
- glossy transparent
(3) Attach the router to the wall mount.
Screw Fixed Mount
(1) Align the wall mount to the wall. Secure 4 screws through the wall mount holes into the wall.
Diagram of Installing Mounting Frame
( 2) Attach the router to the wall mount.
Please maintain a minimum distance of 20cm from the human body when using the product.
Hong Kong Office
GL Technologies (Hong Kong) Limited
Unit 601, Building 5W, Hong Kong Science
Park, Shatin, N.T., Hong Kong
Shenzhen Office
Shenzhen Guanglianzhitong Tech Co., Ltd.
Room 305 – 306, Skyworth Digital Building, Shiyan Street,
Baoan District, Shenzhen, China, 518000
( +86-0755-86606126 )
ver. 20230928
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>