GL iNET GL-X300B Industrial 4G LTE Gateway User Guide
- June 6, 2024
- GL iNet
Table of Contents
**GL iNET GL-X300B Industrial 4G LTE Gateway User Guide
**
SETTING UP
Insert Cards & Power On
When powered up, your router will broadcast a Wi-Fi signal with the SSID: GL- X300B-xxx.
Hot plug for standard SIM card is not supported for this router.
Connect via Wi-Fi
Connect to the 2GHz Wi-Fi called GL-X300B-xxx, and input the default Wi-Fi password goodlife, which is also printed on the bottom of the router.
Set up Router
Visit http://192.168.8.1 in your browser to set up your router; start by choosing your preferred language.
SUPPORT
Repair / Reset
If you cannot access the web-based setup page or cannot connect to the router, you can press the Reset button:
- Press and hold for 3 seconds, and then release to repair your network.
- Press and hold for 10 seconds, and then release to reset the router to factory settings. All user data will be cleared.
https://docs.gl-inet.com/en/3/
Technical Supports
- For more detailed and updated instructions, please visit our website docs.gl-inet.com
- For further questions, you can get help from the following ways:
- Email to [email protected]
- Message us on our Facebook: facebook.com/gl.inet.wifi/
- Post questions in our forum: forum.gl-inet.com
- Ask professionals in other forums e.g. OpenWrt, LEDE or other professional websites
WARRANTY
- We provide one year limited warranty for routers and 3-month limited warranty for accessories.
- Extra warranty may apply according to the local law in which the product purchase took place.
- Highly recommend using the included 12V/1A power adapter.
- Any damage to the router caused by not following the instructions will render this warranty null and void.
- Any damage to the router caused by modifying the PCBA, components or case will render this warranty null and void.
- Issues caused by the use of third-party firmware may not get official support from us.
- Any damage to the router caused by inappropriate use, e.g. inappropriate voltage input, high temperature, dropping in the water or on the ground will render this warranty null and void.
- Pictures on the instructions are only for reference. We reserve the right to change or modify these materials without further notice.
FCC ID:2AFIW-X300B
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help important announcement.
FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator and your body. This transmitter
must not be co-located or operating in conjunction with any other antenna or
transmitter.
The Equipment named above is confirmed to comply with the requirements setout
in the European Council Directive on the Approximation of the Laws of the
Member States relating to RED (2014/53/EU). The equipment passed the test
which was performed according to the following European standards:
EN 301 489-1 V2.2.3; EN 301 489-3 V2.1.1；EN 301 489-17 V3.2.2; EN 301 489-52
V1.1.0; EN 300 328 V2.2.2 ; EN 301 511 V12.5.1; EN 301 908-1 V13.1.1; EN 301
908-2 V11.1.2; EN 301 908-13 V11.1.2; EN 62311:2008
EN62368-1:2014+A11:2017
This product uses WiFi 2.4GHz Operating Frequency is 2400~2483.5MHz;
The Product comply with Directive 2011/65/EU and its amendment directive
2015/863/EU (Rohs2.0)
Hong Kong Office
GL Technologies (Hong Kong) Limited
Unit 203, 2/F, Building 19W, 19 Science Park West Avenue,
Hong Kong Science Park, Pak Shek Kok, N.T., Hong Kong
Shenzhen Office
Shenzhen Guanglianzhitong Tech Co., Ltd.
Room 305 – 306, Skyworth Digital Building, Shiyan Street,
Baoan District, Shenzhen, China, 518000
( +86-0755-86606126 )