Adexa ZBS-15 Ice Maker & Crusher Instruction Manual
- June 6, 2024
- Adexa
Table of Contents
ZBS-15 Ice Maker & Crusher
Instruction Manual
Thank you for choosing our ice maker Please read this Instruction Manual carefully before using this product so as to ensure proper use. After reading this manual, please keep it in a safe place and refer to it when necessary.
Safety Notice
In order to avoid any accidents, please refer to the following operations:
- Disconnect power before servicing.
- Do not pull directly on the wire when plugging or unplugging the unit.
- If ice is abnormal, please call the seller.
- It is normal for the compressor and condenser surface to reach temperatures between 70°C and 90°C during operation and surrounding areas may be hot. Please don’t touch it
- Due to fast freezing, ice cubes may appear “Cloudy”. This is trapped air in the water and it will not affect the quality or taste of ice.
- When out of use, please open the drawer at least 2cm to allow for air circulation and avoid any metallic components becoming rusted.
- If the supply cord is damaged, it must be replaced by the manufacturer or its service agent or a similarly qualified person in order to avoid a hazard.
- This appliance can be used by children aged from 8years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning the use of the appliance in a safe way and understand the hazards involved.
- Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision
- WARNING: fill with bottled or good quality tap water only. (Do not fill with fruit juices or other drink types).
- WARNING Keep the air vents on the sides of the machine unblocked at all times.
- WARNING Do not use mechanical devices or other means to accelerate the defrosting process, other than those recommended by the manufacturer.
- WARNING Do not damage the refrigerant circuit.
- WARNING Do not use electrical appliances inside the food storage compartments of the appliance unless they are of the type recommended by the manufacturer.
Description
1 Viewing window
2 LCD Screen
3 Control Panel
4 Crushed Ice & Water Outlet
Water Puncher
6 Water Collecting Tray| 7 Ice Outlet
8 Water Reservoir Door
9 Ice Puncher
10 Nameplate
11 Water Inlet Hole
12 Power Cord
---|---
Specifications
Daily Ice Output:…………………….. 15-18kg/24h
Ice Storage Capacity:……………………………….. 600g
Water Reservoir Capacity:……………………………………………… 1.8L
Refrigerant…………………………………………………………. R600a
Dimension………………………………………………. 340450453mm
Before/First Use of Your Ice Maker
- During transportation, the incline angle of the cabinet should not be over 45° .Do not turn the Ice maker upside down. As this may damage the compressor and sealed system.
- Remove all packing material and carefully check your ice maker to ensure it is in good condition and that there is no damage to the ice maker or power cord and plug.
- The Ice maker should be placed horizontally on a level surface. To ensure proper ventilation for your Ice makers allow 150mm of space at the top, the back, and on each side. Do not install the Ice maker near an oven, radiator, or any other heat source.
- Before using the Icemaker for the first time, please wait 2 hours after positioning it, and keep the front lid open for at least 2hours
- .Ensure that the voltage indicated on the ice maker corresponds with the voltage in your home.
- Pure water is not allowed to be used on this unit, spring water is recommended.
- Please always keep the viewing window close during ice making.
Control Panel Operation
Display
|
Explanation
---|---
| The unit has a problem, needs to take off the plug, and restart it. If it
appears again, then ask for service
| Ice is full
| Water is not enough in the water reservoir, need to add water
| Unit is dispensing ice cubes
| Unit is dispensing water
| Ice on making, if S at the right top hand of it, then means small size ice
on making if L at right bottom hand, then means large size ice on making
| Crushed ice in the process
Button
|
Operation Operation
CRUSHED ICE| Press it, get to get the crushed ice.
Press it again, the unit will stop crushed ice in 5seconds
SMALL or LARGE| Press button SMALL to turn on/off the small size ice making
function
Press button LARGE to turn on/off the large size ice making function
ON/OFF| Press it to turn on or off the power
Operating Instructions
Step 1 Plugin the machine into the socket.
Step 2 Add water as Sketch A or Sketch B Step 3 Press the ON/OFF
button to turn on or off the power. }
Step 4 Water will be pumped into the water tray from the water reservoir
automatically, this takes about 30 seconds
Nobte: If no water is pumped to the water tray over two cycles but the water
in the reservoir is enough, then please open the drain cap, and let several
drops of water run out. Then press the ON/OFF button again to restart the unit
Step 5 Select the button SMALL, LARGE to start the ice making function
you may need
Note: when temperature lower than 15degrees, S/SMALL is recommended, when the
temperature is over 30degrees, L/LARGE ice is recommended.
Step 6 Ice making cycle begins, ice will be frozen onto the evaporator
fingers.
Step 7 Once ice making cycle is finished, the water tray will tilt
forward; the remaining water flows back to the water reservoir and the ice
cubes will drop from the fingers.
Step 8 In about 15-35 seconds, the water tray will tilt backward, ice
will be pushed to the ice reservoir directly, unit back to work from step 4 to
step 6 again
Step 9 Push the ice cube dispenser puncher button to get ice, the
indicator will be on
Note: Please put your cup below the ice cube dispenser shoot directly.
Notice: If the ice is stored in the unit for a long time, the ice may
freeze and stick together, then no ice will be dispensed even the ice is full,
if so, please kindly use scoop included in the unit to break the ice first,
then push the puncher button.
Step 10 Press the unit starts to dispense crushed ice, press it again,
the unit will stop crushed ice in 5seconds.
Step 11 Press the ON/OFF button to turn off the power of unit
Step 12 Push the puncher on the left side of the unit, cold water will
come out
Note: if you need to get cold water, at least the ice-making function
should be turned on.Please make sure your cup is below the cold water outlet,
or water will be splashed everywhere
Step 12 If you need to take off the pipe, replace it or insert the anti-
drain plug, please do as follows: Firstly take off the blue ring named as A,
then press the white ring(lock) at the outer side named as B,At last take out
the pipe
Caring
- Clean the inner liner, ice collecting tray, water box, ice shovel, and evaporator frequently. When cleaning, unplug the unit and remove the ice cubes. Use a diluted solution of water and vinegar to clean the inside and the outside surface of the ice maker. Do not spray ice maker with chemicals or diluted agents such as acids, gasoline or oil. Rinse thoroughly before starting.
- Keep ventilation openings in the appliance enclosure, or in the built-in structure, clear of obstruction. Do not use mechanical devices or other means to accelerate the defrosting process, other than those recommended by the manufacturer
- Always use fresh water before starting ice production either at initial installation or after a long shut-off period.
Troubleshooting
- Please note, if a power failure occurs due to disconnection of the power cord, or the off power button has been pushed off during an ice-making cycle, small ice chips may form and lodge in the automatic shovel causing it to jam. If this occurs, the ice chips may be removed by disconnecting the power cord and gently pushing the shovel to the rear of the cabinet and removing the ice chips, then restarting.
- Please restart the ice maker by pressing Stop and then Start. If the ice shovel does not push the ice into the ice collector after the formed ice drops from the evaporator finger while at the same time the M light is on, check to see if the water tray is horizontal or balanced. If not then adjust by pressing the ice shovel lightly with your finger. Then re-start the ice maker.
Problem | Possible Reasons | Suggested Solutions |
---|---|---|
The compressor works abnormally with a Buzzing noise. | The voltage is lower | |
than recommended. | Stop the ice maker and do not restart until the voltage is |
normal.
The compressor is hurt during transportation| Stop right away, and keep it on
a flat surface for 24h, then restart
ADD WATER indicator lights up| The water is not enough| Fill water to the MAX
line, then press the start button to restart.
The pump is full of air| Open the drain cap, and let several drops of water
run out, then restart
The pump is blocked| Clean the water pump after taking it out
The pump is broken| Replace pump
Indicator lights on display are not on.| Blown fuse/ No power| Replace fuse /
Turn power on
The Ice made is too large and with pieces sticking together.| Wrong ice size
is selected| Select small size if the temperature is cool
Ice from the previous batch was left in the ice tray| Stop the unit right
away, restart the unit till the ice in the water tray meltdown
The evaporator is too low| Shift the evaporator a little up.
Ice made,but no push the ice _basket| The ice shovel is broken| Replace the
ice shovel
indicating| The water tray is blocked by an ice cube.| Clear the ice under the
ice shovel, then restart the machine
The motor is dead| At standby mode, push the water tray back till a click
sound and then pull it forward till a click, do this for 5times. Then restart
the unit
The machine is running, but water is warmer than beginning| The magnetic valve
is dead| Turn on the unit for a minute, stop and take off the plug. repeat for
5times, restart the unit
The magnetic valve is broken| call for service
Ice is made, however, it won’t drop from the evaporator| The magnetic valve is
broken| call for service
---|---|---
PCB is broken
The ice-making process is right, but no ice is made.| There is no refrigerant
in the compressor| call for service