BaBylissPRO FXX3S FX3 Cord-Cordless Double Foil Shaver Instruction Manual

FX3

Operating Instructions
CORD/CORDLESS
DOUBLE FOIL
SHAVER
Model FXX3S

For your safety and continued enjoyment of this product, always read the instruction book carefully before using it.

IMPORTANT SAFETY INSTRUCTIONS

When using electrical appliances, especially when children are present, basic safety precautions should always be taken, including the following:

READ ALL INSTRUCTIONS BEFORE USING KEEP AWAY FROM WATER

DANGER ­ Any appliance is electrically live, even when the switch is off. To reduce the risk of death or injury by electric shock:

1. Always unplug the appliance from the electrical outlet immediately after using (except when charging unit).
2. Do not place or store appliances where they could fall or be pulled into a tub or sink.
3. Do not use appliances while bathing or in the shower.
4. Do not place the appliance in or drop into water or other liquids.
5. If the appliance has fallen into the water, do not reach for it. Unplug immediately.
6.  Unplug this appliance before cleaning.

WARNING – To reduce the risk of burns, electric shock, fire, or injury to persons:

1. Keep the appliance dry.
2. Except when charging, this appliance should never be left unattended when plugged in.
3. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge unless they have been given supervision or instruction concerning the use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance.
4. Use appliance only for its intended use as described in this manual. Use only attachments recommended by the manufacturer. Do not use an extension cord to operate the appliance.
5. Never operate the appliance if it has a damaged cord or plug,is not working properly, has been dropped or damaged, or has been dropped into water. Return the appliance to a BaBylissPRO Service Center for examination and repair.
6. Keep the appliance cord away from heated surfaces.
7. Do not pull, twist or wrap the cord around the appliance.
8. Keep the air openings free of lint, hair, and similar objects.
9. Never drop or insert any object into any opening on the appliance.
10.  Do not place the appliance on any surface while it is operating.
11. Do not use this appliance with a damaged or broken foil or cutter, as injury to the skin may occur.
12.  Do not use the appliance outdoors or where aerosol (spray) products are being used or where oxygen is being administered.
13. Do not crush, heat above 212° F (100° C) or incinerate the appliance, due to the risk of fire, explosion, or burns.
14. Always attach plug to appliance first, then to outlet. To disconnect, turn all controls to OFF (O) position then remove from outlet.
15. For the purpose of recharging the battery, only use the detachable charging cord provided with this appliance.

SAVE THESE INSTRUCTIONS OPERATING INSTRUCTIONS

1. Before using the shaver for the first time, charge continuously for 3 hours. Maximum battery capacity will only be reached after 3 charging and discharging cycles.

2. Make sure the switch on the shaver is in the OFF (O) position. Connect the charging jack into the receptacle on the bottom of the shaver. Plug the adapter into an electrical outlet that has the same voltage listed on the label affixed to the adapter. The charging indicator will run up to indicate that the charging has begun. When the battery is fully charged, the LED light will stop running up and all 4 charging lights will remain alight. Charging is complete after 3 hours.

3. This product has 4 LED lights that indicate battery capacity when charging or discharging.
   • When all 4 lights are illuminated blue, it indicates 100% battery capacity.
   • When 3 lights are illuminated blue, it indicates 75% battery capacity.
   • When 2 lights are illuminated blue, it indicates 50% battery capacity.
   • When 1 light is illuminated blue, it indicates 25% battery capacity.

4. When the product is about to run out of battery, the last charging indicator light will flash to indicate that there is approximately 10 minutes of use of battery capacity remaining.

5. The adapter may become warm while charging. This is normal.

6. Preserving the battery: In order to maintain the optimum capacity of the rechargeable battery, the shaver should be recharged for 3 hours approximately every 6 months.

7. Make sure the switch is in the OFF (O) position when the shaver is not operating.

WARNING: If all 4 charging lights light suddenly starts to flash rapidly, the appliance is faulty. If this happens, please stop charging and remove the adapter from the outlet and contact our Customer Care Center for further advice (see the Warranty section of this information booklet).

FOR DIRECT PLUG-IN OPERATION
Make sure the shaver is off. Connect the charging jack into the receptacle at the bottom of the shaver and plug the adapter into a power outlet.

ON/OFF SWITCH
To operate, simply slide switch to the ON (I) position. To stop operation, set to the OFF (O) position.

VERY IMPORTANT: Cutters must be cleaned and oiled on a regular basis for proper functioning. Failure to regularly clean and oil the cutters will void the warranty.

BASIC INSTRUCTIONS FOR USE

1. Men whose skin is sensitive or easily irritated by shaving, or who suffer from a skin allergy should test one section on the leg or arm before using the shaver on the face.
2. Remove the protective cover and turn on the unit to start shaving. Hold the shaver at a right angle to the area that you want to shave and run the double shaving foil carefully along your skin. Tip: In general, we recommend that you shave against the direction of hair growth, as this is the best way to trim the hair. Pull your skin tight with your fingers in inaccessible areas to achieve optimum results.
3. Switch the shaver off each time after shaving and clean it.
4. Do not push the shaver on the skin too hard, as it could cause irritation, make the shaver warm and prevent a perfect shave.
5. Please note that it takes 2 to 4 weeks for your skin to adapt to a shaver, so please do not change shaving instruments in this period of time.
6. If hair is longer than 1/32″, begin by cutting the hair down first with a trimmer, then use the shaver for a smooth close shave.

FEDERAL COMMUNICATIONS COMMISSION NOTICE

WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for

SUPPLIER’S DECLARATION OF CONFORMITY

Brand: BaBylissPRO®
Model No.: FXX3S
Description: Shaver

Responsible Party: Conair Corporation,
1 Cummings Point Road
Stamford, CT 06902
203-351-9000

Standards: FCC Part 15 Subpart B, ANSI C63.4-2014

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesirable operation.

DATE OF ISSUE: 01/27/2021

USER MAINTENANCE INSTRUCTIONS

TAKING CARE OF YOUR SHAVER
Always switch the shaver off before removing the shaving foil unit!

Ensure that no water gets inside the shaver to avoid the risk of electric shock when it is back in operation.

Never press on the cutting blades or the shaving foil and do not touch them with hard objects, as this can cause irreparable damage to the shaver or parts. Be careful when dealing with the blades, as they are very sharp and pose a risk of injury! When cleaning, do not apply any detergents or scouring agents, and do not use any abrasive or sharp objects. They can cause irreparable damage to the shaver.

NOTE: When cleaning your shaver, make sure the unit is turned off.
CAUTION!

• DO NOT run shaver or cutters underwater. Use only the small brush (included) to clean.
• To clean the external surfaces of the shaver, use a damp cloth. Do not use strong detergents or other chemicals.
• To dry, wipe the surface of the shaver with a dry towel. Do not use a hairdryer or heater to dry the shaver.
• The shaver should not be used until it has completely dried.
• For connection to the power supply not in the U.S.A., use an attachment plug adapter of the proper configuration for a power outlet. The included adapter automatically adjusts to the input voltage. DO NOT USE A VOLTAGE

TO REPLACE FOIL HEAD ASSEMBLY

1. Remove the foil head assembly by pressing the release button located on the side of the shaver. Hold the foil head assembly on both sides and lightly pull it away from the shaver unit.
2. Take the replacement foil head assembly (FXX3RF) out of the package. Align the replacement foil head assembly over the cutters. Carefully move the replacement foil head assembly down towards the shaver unit until it firmly snaps into place. BE CAREFUL NOT TO DAMAGE THE FOILS OR CUTTERS WHILE INSTALLING.

TO REPLACE CUTTERS

NOTE: Always replace the cutters and foil head assembly at the same time.

1. To remove cutters, place your fingers on each side and gently pull up and away from the driveshaft.
2. To replace cutters, remove the new cutters (FXX3RF) from the packaging. Align the cutter with the driveshaft and lightly push down until it snaps into place.
3. Replace the foil head assembly, turn the shaver on to ensure it is working

Daily Maintenance:

1. Press the release button on the side of the shaver and remove the head assembly (see Fig. 1 & 2).
2. Use a cleaning brush to whisk away any debris on and around cutters (see 3).
3. Snap the head assembly closed (see Fig. 4).

Weekly Maintenance:

1. Repeat steps 1 — 3 described in Daily Maintenance.
2. Rinse the head of the shaver under running water (see Fig. 5). NEVER submerge the shaver in
3. Leave head open for
4. Press the shaver head back into place (see Fig. 4 on the previous page).

BATTERY REMOVAL
When your rechargeable shaver reaches the end of its useful life, the lithium-ion battery must be removed from the shaver and be recycled or disposed of properly in accordance with your state and local requirements. If this is not required by law, you may elect to dispose of the shaver with the battery.

To remove the rechargeable battery:

1. Unplug the shaver.
2. Run shaver until motor stops.
3. Remove foil head from shaver (press release button and pull the head away from shaver body).
4. Remove cutters by pulling away from drive shafts.
5. Remove 2 screws from bottom housing. Remove 2 screws from metal plate undercutters.
6. Lightly pull the bottom housing away from the top housing.
7. Cut battery contact plate from PCB board.
8. Dispose of

CONTAINS A LITHIUM-ION BATTERY. MUST BE COLLECTED, RECYCLED, OR DISPOSED OF PROPERLY. DO NOT DISPOSE OF IN THE MUNICIPAL WASTE.

CAUTION: ALL RECHARGEABLE BATTERIES MUST BE RECYCLED OR DISPOSED OF IN ACCORDANCE WITH APPLICABLE STATE AND LOCAL REGULATIONS. DO NOT PUT IN FIRE OR MUTILATE, AS THE BATTERY MAY BURST OR RELEASE TOXIC MATERIALS. DO NOT SHORT- CIRCUIT, AS THIS MAY CAUSE BURNS.

CORD/CORDLESS DOUBLE FOIL SHAVER

WARNING:
IF YOU THINK THE POWER IS OFF WHEN THE SWITCH IS OFF, YOU’RE WRONG.

Everyone knows that electricity and water are a dangerous combination. But did you know that an electrical appliance is still electrically live even if the switch is off? If the plug is in, the power is on. So when you are not using appliances, keep them unplugged.

LIMITED 2-YEAR WARRANTY (U.S. ONLY)

BaBylissPRO will repair or replace (at our option) your unit free of charge for 24 months from the date of purchase if the appliance is defective in workmanship
or materials.

To obtain service under this warranty, return the defective product to the service center listed, together with your purchase receipt. California residents need only provide proof of purchase and should call 1-800-326-6247 for shipping instructions. In the absence of a purchase receipt, the warranty period shall be 24 months from the date of manufacture.

ANY IMPLIED WARRANTIES, OBLIGATIONS, OR LIABILITIES, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTY OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, SHALL BE LIMITED IN DURATION TO THE 24-MONTH DURATION OF THIS WRITTEN, LIMITED WARRANTY. Some states do not allow limitations on how long an implied warranty lasts, so the above limitations may not apply to you.

IN NO EVENT SHALL BABYLISSPRO BE LIABLE FOR ANY SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY, EXPRESSED OR IMPLIED, WHATSOEVER. Some states do not allow the exclusion or limitation of special, incidental, or consequential damages, so the above limitation may not apply to you. This warranty gives you specific legal rights, and you may also have other rights, which vary from state to state.

Service Center
BaBylissPRO
Service Department
7475 N. Glen Harbor Blvd.
Glendale, AZ 85307
1-800-326-6247
©2021 BaBylissPRO
205 Shelhouse Drive
Rantoul, IL 61866
www.babylisspro.com
21FA078240

IF YOU LIVE OUTSIDE CANADA, PLEASE CONTACT YOUR LOCAL DISTRIBUTOR.

CANADIAN TWO YEAR REPLACEMENT WARRANTY

Dannyco Professional is the exclusive Canadian distributor of this product. We offer the following excellent warranty on your professional electrical appliance. Keep your sales slip. This is your proof of purchase and your guarantee. This guarantee is not valid in case of abuse, misuse, alterations, or repairs done by unauthorized persons. Before returning your defective electrical product, please read the warranty conditions listed in this brochure.

Should your professional electrical appliance possess a manufacturer’s defect, it may be exchanged by your distributor or Dannyco Professional at no charge within TWO YEARS from the date of purchase, if the electrical appliance is accompanied by proof of purchase.

If you are sending your defective appliance, which is covered by this guarantee, directly to the Dannyco Professional Service Center, it must be accompanied by the following:

1. your dated sales slip;
2. a precise description of the defect;
3. your complete return address and daytime phone number; and,
4. a $10 money order for postage and handling.

Please return your defective appliance to:

ATTN: Dannyco Professional Service Center
CONAIR CONSUMER PRODUCTS ULC
100 Conair Parkway
Woodbridge, Ontario L4H 0L2

This warranty applies only to residents of Canada. Products shipped from outside of Canada will not be processed and will not be returned to the sender.
For questions regarding this product, you may call the Dannyco Professional Service Center at 1-800-363-0707, or email us at customerservice@dannyco.com.

21FA078240
IB-17245

References

• BaBylissPRO | Hot Tools for Hair Styling & Grooming Tools

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>