eve Water Guard 2nd Generation User Guide
- June 6, 2024
- eve
Table of Contents
Get Started
Get started
-
Plug Eve Water Guard into an electrical outlet and connect the supplied sensing cable to the 3.5 mm (1/8“) socket on the bottom. The entire length of the cable serves as a water detection sensor and is extendable (optional accessory).
-
Download the Eve app from the App Store.
-
Open the Eve app and tap Add Accessory. Eve will now guide you through the setup process.
If you have already set up another accessory, go to
Settings in Eve to add Eve Water Guard to your home.
Enjoy
Access Eve Water Guard using the Eve app, the Home app, and Siri.
| View status | Alarm Test | Install firmware updates |
|---|---|---|
| Review previous events | Mute alarm |
| View status | Configure notifications | Configure guest access |
|---|
Ask for status
To test the alarm, go to the Settings of Eve Water Guard, tap Alarm Test and follow the instructions in the app. Performing this test is recommended at least every three months.
If the sensing cable detects water, a loud alarm will sound and the LEDs will flash. Please use the Eve app to mute the alarm.
Securely access Eve Water Guard while you’re away from home and set up powerful automation. Any Apple TV HD, Apple TV 4Kor HomePod using the same iCloud account as your iPhone will automatically serve as a home hub, no further setup is required.
Eve is designed to safeguard your personal data. All data is fully encrypted
and only transferred directly between your Eve Water Guard and iPhone, iPad or
home hub.
Learn more at evehome.com/privacy
Legal Information
This device complies with part 15 of the FCC Rules and Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, you are encouraged to try to correct the interference by one or more of the following measures: reorient or relocate the receiving antenna; increase the separation between the equipment and receiver; consult the dealer or an experienced radio/TV technician for help.
This Class B digital apparatus complies with Canadian ICES-003.
This equipment complies with FCC RF, IC RSS-102, and CE radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Changes or modifications not expressly approved by Eve Systems could void your authority to operate this device.
Legal Information
For questions about compliance with FCC regulations, please contact:
Compliance Officer, Eve Systems, 100 Pine St., Suite 1250, San Francisco CA
94111, USA.
Hereby, Eve Systems declares that this device is in compliance with the
essential requirements and other relevant provisions of Directive 2014/53/EC.
The declaration of conformity is available at
www.evehome.com/doc
Purpose of control: operating control; construction of control: plug-in operating control; type 1 action, operating time: continuous; control pollution degree: 2; impulse voltage: 1500 V; frequency range: 2402 – 2480 MHz (BLE) / 2405 – 2480 MHz (Thread); max. EIRP: 10 dBm; power consumption: active < 0.5 W, standby < 0.2 W
Product: 10EBZ8701
Model: 20EBZ8701
Part: 51EBZ8702
FCC ID: SNE-WLS-002
IC: 11192A-WLS002
Reset
Please keep your HomeKit setup code in a safe place. You need it to securely add Eve to your home, and nobody but you has a copy.
Room ————————————
Notes ————————————