Haike CT602 Floating Bluetooth Lightshow Speaker User Guide
- June 6, 2024
- Haike
Table of Contents
Floating Bluetooth light show speaker
Please charge before use
Model number: CT602
CT602 is a floating Bluetooth speaker with a light show. It could be used in swimming pools, ponds, yards, parties, indoors and etc. It makes life colorful!
**Introduction to Parameters
**
Bluetooth version | V5.3 |
---|---|
Battery capacity | 2500mAH lithium battery 3.7V |
Working hours | 5-7 hours |
Frequency | 2400MHz-2480MHz |
Protocol | A2DP/AVRCP/HFP/HSP/OPP/HID/SPP/ PBAP/GATT/SM |
Communication distance | 15-25 meters |
Speaker | Mono mixing output 406W, high-fidelity waterproof speaker (0)57mm) |
Dimension | 4.94’x4.94’x6.63′ |
LED light | Yellow,Green, Red,Blue |
LED mode | 8 modes |
Waterproof | IP68 |
It takes about 3 minutes to pair for the first time. After the pairing is
successful, it will automatically pair in the future, which only takes 8
seconds.
2. After power on, if without any pairing, it will enter the sleep state
after 20 minutes, and then shut down after another 40 minutes.
Button Function Description
A. Multifunction Button:
- Long press 3 seconds to power on, and Long press again 3 seconds to power off.
- When playing music, short press this button to pause music, press again to continue playing music.
- When the call is coming, short press the button to answer the phone, and double press the button to refuse the call.
- Double-tap to dial the last-coming call number.
B. “volume-and previous” Button:
Short press the button to play the previous track, long-press the button to
reduce the volume.
C. “volume+and next” Button:
Short press the button to play the next track, long-press the button to
increase the volume.
D. Light mode Button:
I Short press to switch the different LED modes.
- Slow flashing when there is no music: red green blue yellow turns brighter every 20 seconds. when there is music: the LED lights flashes with the music.
- Keep red light
- keep green light
- keep Blue light
- RGB light color change automatically(slow and fast flashing are mixed)
- RGB light color automatically switches slowly
- RGB light color automatically switches quickly
- The light power off.
II: Long press the light button for 8 seconds to restore factory settings
Bluetooth Pairing Settings
Long press on the multifunction button for 3 seconds to power on. Wait for the blue light flash, open the Bluetooth mode on your smartphone and select “CT602” to pair the device. It’s now paired. You can broadcast your music ! If not, start again or relaunch the CT602.
Charging
Take the USB included. Connect the USB port to a 5V USB outlet and the DC jack
to the CT602. During the charging, the LED indicator will keep red. When the
battery is full the LED indicator is green.
Note: Use the included cable and respect the voltage!
Accessories
1CT602
1User manual
1Charging cable
1Gift box
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment. This
device complies with art15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference
that may cause undesired operation.
Made in China
Documents / Resources
|
Haike CT602 Floating Bluetooth Lightshow
Speaker
[pdf] User Guide
CT602F, 2A4OOCT602F, CT602 Floating Bluetooth Lightshow Speaker, Floating
Bluetooth Lightshow Speaker
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>