beamZ 153.800 ShowBar 2x PAR 6x 4in1 2xButterfly Laser Instruction Manual

beamZ 153.800 ShowBar 2x PAR 6x 4in1 2xButterfly Laser

Congratulations to the purchase of this Beamz product. Please read this manual thoroughly prior to using the product in order to benefit fully from all features.
Read the manual prior to using the product. Follow the instructions in order not to invalidate the warranty. Take all precautions to avoid fire and/or electrical shock. Repairs must only be carried out by a qualified technician in order to avoid electrical shock. Keep the manual for future reference.

•  Prior to using the product, please ask advice from a specialist. When the unit is switched on for the first time, some smell may occur. This is normal and will disappear after a while.
•  The unit contains voltage carrying parts. Therefore do NOT open the housing.
•  Do not place metal objects or pour liquids into the product. This may cause electrical shock and malfunction.
•  Do not place the product near heat sources such as radiators, etc. Do not place the unit on a vibrating surface. Do not cover the ventilation holes.
•  The product is not suitable for continuous use.
•  Be careful with the mains lead and do not damage it. A faulty or damaged mains lead can cause electrical shock and malfunction.
•  When unplugging the product from a mains outlet, always pull the plug, never the lead.
•  Do not plug or unplug the unit with wet hands.
•  If the plug and/or the mains lead are damaged, they need to be replaced by a qualified technician.
•  If the product is damaged to such an extent that internal parts are visible, do NOT plug the unit into a mains outlet and DO NOT switch the product on. Contact your dealer. Do NOT connect the product to a rheostat or dimmer.
•  To avoid fire and shock hazard, do not expose the product to rain and moisture.
•  All repairs should be carried out by a qualified technician only.
•  Connect the product to an earthed mains outlet (220-240Vac/50Hz) protected by a 10-16A fuse.
•  During a thunderstorm or if the product will not be used for a longer period of time, unplug it from the mains. The rule is: Unplug it from the mains when not in use.
•  If the product has not been used for a longer period of time, condensation may occur. Let the unit reach room temperature before you switch it on. Never use the product in humid rooms or outdoors.
•  During operation, the housing becomes very hot. Do not touch it during operation and immediately after.
•  To prevent accidents in companies, you must follow the applicable guide lines and follow the instructions.
•  Secure the product with an extra safety chain if the unit is ceiling mount. Use a truss system with clamps. Make sure nobody stands in the mounting area. Mount the effect at least 50cm away from inflammable material and leave at least 1 meter space on every side to ensure sufficient cooling.
•  This product contains high intensity LEDs. Do not look into the LED light to prevent damage to your eyes.
• Do not repeatedly switch the product on and off. This shortens the life time.
•  Keep the unit out of the reach of children. Do not leave the unit unattended.
•  Do not use cleaning sprays to clean switches. The residues of these sprays cause deposits of dust and grease. In case of malfunction, always seek advice from a specialist.
• Only operate the product with clean hands.
•  Do not force the controls.
• If the product has fallen, always have it checked by a qualified technician before you switch the product on again.
•  Do not use chemicals to clean the unit. They damage the varnish. Only clean the product with a dry cloth.
•  Keep away from electronic equipment that may cause interference.
•  Only use original spares for repairs, otherwise serious damage and/or dangerous radiation may occur.
•  Switch the product off prior to unplugging it from the mains and/or other equipment. Unplug all leads and cables prior to moving the product.
•  Make sure that the mains lead cannot be damaged when people walk on it. Check the mains lead before every use for damages and faults!
• The mains voltage is 220-240Vac/50Hz. Check if power outlet match. If you travel, make sure that the mains voltage of the country is suitable for this product.
•  Keep the original packing material so that you can transport the product in safe conditions

The product has been certified CE. It is prohibited to make any changes to the product. They would invalidate the CE certificate and their guarantee!
NOTE: To make sure that the unit will function normally, it must be used in rooms with a temperature between 5°C/41°F and 35°C/95°F.

Electric products must not be put into household waste. Please bring them to a recycling centre. Ask your local authorities or your dealer about the way to proceed. The specifications are typical. The actual values can slightly change from one unit to the other. Specifications can be changed without prior notice.
prior notice.

Do not attempt to make any repairs yourself. This would invalid your warranty. Do not make any changes to the product. This would also invalid your warranty. The warranty is not applicable in case of accidents or damages caused by inappropriate use or disrespect of the warnings contained in this manual. Beamz cannot be held responsible for personal injuries caused by a disrespect of the safety recommendations and warnings. This is also applicable to all damages in whatever form.

LASER SAFETY

Read for the commissioning of the laser all safety instructions and technical data of this manual carefully and thoroughly.

Laser Light is different from any other light source with which you may be familiar. The light from this product can potentially cause eye injury if not set up and used properly. Laser light is thousands of times more concentrated than light from any other kind of light source. This concentration of light power can cause instant eye injuries, primarily by burning the retina (the light sensitive portion at the back of the eye). Even if you cannot feel “heat” from a laser beam, it can still potentially injure or blind you or your audience. Even very small amounts of laser light are potentially hazardous even at long distances. Laser eye injuries can happen quicker than you can blink.

It is wrong to assume that a single beam of a bundle of hundreds by the laser beams made, it cannot cause injury.
It is also incorrect to assume that it is safe to look at a moving beam. In the laser safety regulation, it is not legal to aim Class 3B/4 lasers in areas which people can get exposed also on a dance floor.

Caution:

• Do not point lasers at people or animals.
•  Never look into the laser aperture or laser beams, this can potentially cause instant eye injury or blindness if laser light directly strikes the eyes.
•  Do not point lasers in areas in which people can potentially get exposed, such as uncontrolled balconies, etc.
• Install the laser units such that laser beams above the audience move See section later in this manual.
• Test the laser units always first before the public is present.
•  Do not point lasers into the public or at highly reflective surfaces such as windows, mirrors and shiny metal. Even laser reflections can be hazardous.
•  Never point a laser at aircraft or into the sky, this is a federal offense.
•  Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.
•  Do not expose the output optic (aperture) to cleaning chemicals.
•  The operation of a laser is only allowed if the show is controlled by a skilled and well-trained operator familiar with the requirements that are needed.
•  Do not use laser if housing is damaged or open, or if optics appear damaged in any way.
•  Never leave this device running unattended.
•  Always use appropriate lighting safety cables when hanging lights and effects overhead.

The legal requirements for using laser entertainment products vary from country to country. The user is responsible for the leg al requirements at the location/country of use.

WARNING:

This unit contains laser components with high power, live parts and parts that emit radiation. Therefore, DO NOT OPEN the housing, THIS CAN BE FATAL. It can also cause blindness, skin burns and fires.

Eye damage occurs faster than you can blink your eyes.
Further guidelines and safety programs for safe use of lasers can be found in the ANSI Z136.1 Standard “For Safe Use of Lasers”, available from “www.laserinstitute.org”. Many local governments, corporations, agencies, military and others, require all lasers to be used under the guidelines of ANSI Z136.1. Laser Display guidance can be obtained via the International Laser Display Association, www.laserist.org.

Attention! The use in France is only allowed to the professional user and not to the end user. See decision: www.legifrance.gouv.fr “www.laserinstitute.org”. Many local governments, corporations, agencies, military and others, require all lasers to be used under the guidelines of ANSI Z136.1. Laser Display guidance can be obtained via the International Laser Display Association, www.laserist.org.

INSTALLATION

CAUTION: Please consider the respective national norms during the installation! The installation must only be carried out by an authorized employee or dealers!

This fixture has been designed to be hung. It is recommended for safety purposes, your lighting effect are properly mounted using a suitable hanging clamp and safety cable. Items appropriate for safe and effective mounting are easily sourced from your lighting vendor.
International laser safety regulations require that lasers must be operated in the fashion illustrated below, with a minimum of 3 meters (9.8 ft) of vertical separation between the floor and the lowest laser light vertically. Additionally, 2.5 meters of horizontal separation is required between laser light and audience or other public spaces.

CAUTION: Use of controls, adjustments, or performance of procedures other than what is specified  herein may result in hazardous radiation exposure!

• The installation of the fixture has to be built and constructed in a way that it can hold 10 times the weight for 1 hour without any harming deformation.
• Always use the supplied mounting bracket to hang the fixture.
• The fixture should aid of a mounting bracket (not included) to the supplied mounting bracket to be confirmed.
• The installation must always be secured with a secondary safety attachment, e.g. an appropriate catch net. This secondary safety attachment must be constructed in a way that no part of the installation can fall down if the main attachment fails.
•  Make sure the area below the installation place is free from unwanted persons during rigging, de-rigging and servicing.
•  The operator has to make sure that safety-relating and machine-technical installations are approved by an expert before taking into operation for the first time and after changes before taking into operation another time.
•  The operator has to make sure that safety-relating and machine-technical installations are approved by a skilled person once a year.
•  The fixture should be installed in the position where persons cannot reach.

CAUTION: When installing the device, make sure there is no highly in inflammable material (decoration articles, etc.) in between a distance of min 0.5 meter.

 UNPACKING INSTRUCTION

CAUTION! Immediately upon receiving the product, carefully unpack the carton, check the contents to ensure that all parts are present, and have been received in good condition. Notify the shipper immediately and retain packing material for inspection if any parts appear damage from shipping or the package itself shows signs of mishandling. Save the package and all packing materials. In the event that the product must be returned to the factory, it is important that the product be returned in the original factory box and packing.

If the device has been exposed to drastic temperature fluctuation (e.g. after transportation), do not switch it on immediately. The arising condensation water might damage your device. Leave the device switched off until it has reached room temperature.

POWERSUPPLY

On the label on the backside of the product is indicated on this type of power supply must be connected. Check that the mains voltage corresponds to this, all other voltages than specified, the light effect can be irreparably damaged. The product must also be directly connected to the mains and may be used. No dimmer or adjustable power supply.

DISPLAY

The control board offer several features: you can simple set the starting address, run the pre-programmed program or make a reset. The main menu is accessed by pressing the Mode-button, browse through the submenu by pressing Up or Down.
Press the Enter-button in order to select the desired menu.
You can change the selection by pressing Up or Down. Confirm every selection by pressing the Enter-button.
You can leave every mode by pressing the Mode-button. The functions provided are described later in this manual.

DMX-512 CONNECTION

If you are using a standard DMX controller, you can connect the DMX-output of the controller directly to the DMX-input of the first unit in a DMX-chain. Always connect the output of one unit with the input of the next unit until all units are connected.
If you use a controller with 5 pin DMX connection you will need to use a 5-pin to 3-pin adapter.

CONFIGURATION STAND ALONE

Set the product in one of the standalone modes to control without a DMX controller.
Never connect a product that’s operating in standalone mode with DMX-chain. Product can interference on DMX signal.
Auto mode
To enable the auto effect (Automatic All) mode:

1. Press repeatedly until “AUTO” blinks on the display.
2.  Press
3.  Press or to select the desired Automatic mode (AU01 or AU02).
4.  Press to put the fixture into the selected Auto-Active mode.

Sound mode
To enable the sound effect (Sound-Active All) mode:

1. Press repeatedly until “SOND” blinks on the display.
2. Press
3. Press or to select the desired Sound-Active mode (So01, So02 or So03).
4. Press to put the fixture into the selected Sound-Active mode.

Note: The product will only respond to low music frequencies (bass and drums).

Speed
To adjust the auto speed mode: 

1. Press repeatedly until “Sped” blinks on the display.
2. Press
3. Press or to select the desired Speed mode (Sp01, Sp02, Sp03, Sp04, Sp05, Sp06, Sp07, Sp08 or Sp09).
4. Press to put the fixture into the selected Speed mode.

Sensitivity
To adjust the mic value adjustable: 

1.  Press repeatedly until “SENS” blinks on the display.
2.  Press
3. Press or to select the desired sensitivity (SE01, SE02, SE03, SE04, SE05, SE06, SE07, SE08 or SE09).
4. Press to activate.

Silent Scene
To enable the silent scene: 

1. Press repeatedly until “SILE” blinks on the display.
2. Press
3. Press or to select ON or OFF.
4. Press to activate.

IR remote
To enable the IR remote: 

1.  Press repeatedly until “INFR” blinks on the display.
2. Press
3. Press or to select ON or OFF.
4. Press to activate.

Footswitch
To enable the wireless footswitch: 

1. Press repeatedly until “FOOT” blinks on the display.
2. Press
3. Press or to select ON or OFF.
4. Press to activate.

Address
When selecting a DMX starting address, always consider the number of DMX channels used by the fixtures. If you choose a starting address that is too high, you could restrict the access to some of the product’s channels.
The ShowBar uses 2, 9, 18 or 30 DMX channels mode, which means the highest DMX address you can use is 482.
To select starting DMX address:

1. Press repeatedly until the desired DMX personality (2CH, 9CH, 18CH or 30CH) blinks on the display.
2. Press and D** blinks on the display.
3. Press or to select the starting address (d001–d512).
4. Press to put the fixture in DMX mode. The display will continue to blink.

RGBW (Par only)
To set Par to a RGBW custom colours: 

1. Press repeatedly until “RGB” blinks on the display.
2. Press
3. Press or to select the desired colour. (RED, GREEN, BLUE or WHITE)
4. Press to select the colour.
5. Press or to adjust the color saturation (X000–X255).
6. Press to activate.
7. Repeat Steps 3 through 5 for each colour.

Colour (Par + Butterfly effect)
To set both the Par and Butterfly to a preset colour: 

1. Press repeatedly until “COLO” blinks on the display.
2. Press
3. Press or to select the desired colour (You can choose C1 until C15).
4.  Press to activate.

MASTER/SLAVE OPERATION

The Master/Slave mode allows a single ShowBar (the master) to control the actions of one or more ShowBar (the slaves) without the need for a DMX controller. The master will be set to operate in either Automatic or Sound- Active mode, while the slaves will be set to operate in Slave mode. Once set and connected, the slave units will operate in unison with the master.
Setting the slave-unit(s):

1. Press repeatedly until Slav blinks on the display.
2. Press to put the fixture in Slave mode. The display will continue to blink.
3. Repeat steps 1 and 2 for every slave.
4. Connect the DMX output of the first slave unit to the DMX input of the next slave unit.
5.  Connect the DMX input of each subsequent slave unit to the DMX output of the previous slave unit.

Setting the master-unit:

1. Connect the DMX output of the master to the DMX input of the first slave unit.
2. Set the master unit to operate in either Automatic or Sound-Active mode.

REMOTE CONTROL

BLACK OUT Mode
Press off existing modes, Press return the last modes.
AUTO Mode
Automatic mode will enable you to run the automatic programs on the product.
To turn on Automatic mode:

1. Press on the IRC.
2. Press <+> or <–> to choose between the different auto programs.

SOUND Mode
Sound-Active mode will enable the product to respond to the music. To turn on Sound-Active mode: 

1. Press on the IRC.
2. Press <+> or <–> to choose between the different SOUND programs.

STROBE Mode
To adjust the strobe speed of the automatic program and the sound active program. 

1. Press on the IRC.
2. Press <+> or <–> to either increase or decrease the speed of the program.
3. Press again to turn off the strobe.

SPEED Mode
To adjust the speed of the automatic program and the sound active program. 

1. Press on the IRC.
2. Press <+> or <–> to either increase or decrease the speed of the program.

SENSITIVITY Mode
To adjust sound sensitivity for in Sound-Active mode. 

1. Press on the IRC.
2. Press <+> or <–> to either increase or decrease sound sensitivity.

DMX Mode
To enable DMX or disallow DMX on the product.
Press on the remote controller, the product work on the DMX controlling modes.
Manual Mode
To manually control the RGBWAUV percentage:

1. Press on the IRC.
2. Press , , , or (red, green, blue or white) to choose your colour.
3. Press <+> or <–> to either increase or decrease to choose your colour.