reolink Argus Eco Wi-Fi Camera 2MP PIR Motion Sensor Instruction Manual

: June 6, 2024
: reolink

Table of Contents

What’s in the Box
Camera Introduction
Set up the Camera
Charge the Battery
Install the Camera
Mount the Camera
Attach the Camera to a Tree
Notes on PIR Motion Sensor
Important Notes on Rechargeable Battery Usage
Troubleshooting
Notiﬁcation of Compliance
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Reolink Argus Eco
Operational Instruction

What’s in the Box

Camera Introduction

Different states of the status LED:
Red Light: Wi-Fi connection failed
Blue Light: Wi-Fi connection succeeded
Blinking: Standby status
On: Working status

Set up the Camera

Download and Launch the Reolink App or Client software, and follow the onscreen instructions to ﬁnish initial setup.

On Smartphone
Scan to download the Reolink App.

reolink Argus Eco Wi Fi Camera 2MP PIR Motion Sensor - QR
code

https://reolink.com/wp-json/reo-v2/app/download

|
---|---

On PC
Download path of the Reolink Client: Go to https://reolink.com > Support > App & Client.

Charge the Battery

It’s recommended to fully charge the battery before mounting the camera outdoors.

Charge the battery with a power adapter.| Charge the battery with the Reolink solar panel.

For better weatherproof performance, please always cover the USB charging port with the rubber plug after charging the battery.

Charging indicator:
Orange LED: Charging
Green LED: Fully charged

NOTE: The solar panel is NOT included in the package. You can buy one from Reolink official online stores.

Install the Camera

Install the camera 2-3 meters (7-10 ft) above the ground. This height maximizes the detection range of the PIR motion sensor.
For better motion detection performance, please install the camera angularly.

NOTE: If a moving object approaches the PIR sensor vertically, the camera may fail to detect motion.

Mount the Camera

|
---|---
Drill holes in accordance with a mounting hole template and screw the security mount into the wall.
If you are mounting the camera on any hard surface, insert plastic anchors into the holes ﬁrst.| Screw the antenna to the camera and then install the camera on the security mount.
|
Lose the adjusting knob on the mount and adjust the camera to the proper direction.| Stiffen the adjustment knob to lock the camera.

Attach the Camera to a Tree

|
---|---
Thread the provided strap to the mounting plate.| Attach the plate to the security mount with the smaller screws.
|
Fasten the security mount to a tree.| Install the camera and adjust the camera angles as instructed in step 3 in the previous installation guide.

Notes on PIR Motion Sensor

PIR Sensor Detection Distance
The PIR detection range can be customized to meet your speciﬁc needs. You can refer to the following table to set it up in Device Settings via Reolink App.

Sensitivity| Value| Detection Distance
(For moving and living objects)
---|---|---
Low| 0 – 50| Up to 5 meters (16ft)
Mid| 51 – 80| Up to 8 meters (26ft)
High| 81 – 100| Up to 10 meters (33ft)

NOTE: Higher sensitivity offers a longer detection distance but it may lead to more false alarms. It’s recommended to set up the sensitivity level to “Low” or “Mid” when you install the camera outdoors.

Important Notes on Reducing False Alarms

Do not face the camera towards any objects with bright lights, including sunshine, bright lamp lights, etc.
Do not place the camera too close to a place with heavy traffic. Based on our numerous tests, the recommended distance between the camera and the vehicle would be 16 meters (52ft).
Do not place the camera near outlets, including the air conditioner vents, humidiﬁer outlets, the heat transfer vents of projectors, etc.
Do not install the camera at places with strong wind.
Do not face the camera towards a mirror.
Keep the camera at least 1 meter away from any wireless devices, including WiFi routers and phones in order to avoid wireless interference.

Important Notes on Rechargeable Battery Usage

Reolink Argus Eco is not designed for 24/7 full capacity running or around- the-clock live streaming. It’s designed to record motion events and remotely view live streaming only when you need it. Learn useful tips on how to extend the battery life in this post: https://support.reolink.com/hc/en- us/articles/360006991893

Charge the rechargeable battery with a standard and high-quality DC 5V/9V battery charger or Reolink solar panel. Do not charge the battery with solar panels from any other brands.
Charge the battery when temperatures are between 0°C and 45°C and always use the battery when temperatures are between -20°C and 60°C.
Keep the USB charging port dry, clean, and free of any debris, and cover the USB charging port with the rubber plug when the battery is fully charged.
Do not charge, use or store the battery near any ignition sources, such as ﬁre or heaters.
Do not disassemble, cut, puncture, short-circuit the battery, or dispose of the battery in water, ﬁre, microwave ovens, and pressure vessels.
Do not use the battery if it gives off an odor, generates heat, becomes discolored or deformed, or appears abnormal in anyway. If the battery is being used or charged, remove the battery from the device or the charger immediately, and stop using it.
Always follow the local waste and recycle laws when you get rid of the used battery.

Troubleshooting

The camera Is Not Powering on
If your camera is not powering on, please apply the following solutions:

Make sure the power switch is turned on.
Charge the battery with a DC 5V/2A power adapter. When the green light is on, the battery is fully charged.

If these won’t work, please contact Reolink Support https://support.reolink.com/.

Failed to Scan the QR Code on the Phone
If you cannot scan the QR code on your phone, please try the following solutions:

Remove the protective ﬁlm from the camera lens.
Wipe the camera lens with a dry paper/towel/tissue.
Vary the distance between your camera and the mobile phone so that the camera can focus better.
Try to scan the QR code under sufficient lighting.

If these won’t work, please contact Reolink Support https://support.reolink.com/.

WiFi Connection Failed During Initial Setup Process
If the camera fails to connect to WiFi, please try the following solutions:

Please make sure the WiFi band is 2.4GHz, the camera does not support 5GHz.
Ensure that you have entered the correct WiFi password.
Put the camera closer to your router to ensure a strong WiFi signal.
Change the encryption method of the WiFi network to WPA2-PSK/WPA-PSK (safer encryption) on your router interface.
Change your WiFi SSID or password and make sure that SSID is within 31 characters and password is within 64 characters.
Set your password using only the characters available on the keyboard.

If these won’t work, please contact Reolink Support https://support.reolink.com/.

Notiﬁcation of Compliance

FCC Compliance Statement
This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. For more information, visit: https://reolink.com/fcc-compliance-notice/.

Simpliﬁed EU Declaration of Conformity
Reolink declares that this device is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU.

Correct Disposal of This Product
This marking indicates that this product should not be disposed of with other household wastes throughout the EU. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. To return your used device, please use the return and collection systems or contact the retailer where the product was purchased. They can take this product for environmentally safe recycling.

Limited Warranty
This product comes with a 2-year limited warranty that is valid only if purchased from Reolink Official Store or a Reolink authorized reseller. Learn more: https://reolink.com/warranty-and-return/.
NOTE: We hope that you enjoy the new purchase. But if you are not satisﬁed with the product and plan to return, we strongly suggest that you reset the camera to factory default settings and take out the inserted SD card before returning.

Terms and Privacy
Use of the product is subject to your agreement to the Terms of Service and Privacy Policy at https://reolink.com. Keep out of reach of children.

End-User License Agreemen t
By using the Product Software that is embedded on the Reolink product, you agree to the terms of this End User License Agreement (“EULA”) between you and Reolink. Learn more: https://reolink.com/eula/.

ISED Radiation Exposure Statement
This equipment complies with RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body.

OPERATING FREQUENCY (the maximum transmitted power)
2412MHz—2472MHz (18dBm)

Technical Support
If you need any technical help, please visit our official support site and contact our support team before returning the products, https://support.reolink.com.

REOLINK INNOVATION LIMITED
Room B, 4th Floor, Kingway Commercial Building, 171-173 Lockhart Road, Wan Chai, Hong Kong

Product Ident GmbH
Hoferstasse 9B, 71636 Ludwigsburg, Germany
prodsg@libelleconsulting.com

July 2020
QSG2_A