fantastic Jive Wireless TWS Headset & Charger User Manual

: June 6, 2024
: fantastic

Table of Contents

fantastic Jive Wireless TWS Headset & Charger
Package Contents
Overview
Getting Started
Safety advice
Technical Specifications
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

fantastic Jive Wireless TWS Headset & Charger

fantasti-Jive-Wireless-TW-Headset-&-Charger-User-IMAGE

Thank you for choosing this Fontastic® product. Please read this user manual carefully and comply with the safety instructions.

Package Contents

2 x wireless headset Jive
Storage and charging case
Wireless charger
USB Type-C™ cable
Micro USB cable
3 pairs of earbuds (small, medium & large)
User manual

Overview

Status LED
Multifunction sensor
Earbud
Speaker
Microphone
Charging Pin
Headset insertion
Charging status indicator (on the bottom)
USB Type-C™ charging port (on the bottom)
Status LED
Charging area
Micro USB connector

fantasti-Jive-Wireless-TW-Headset-&-Charger-User-FIG-1

Getting Started

Charging the headset
Insert the headset into the charging case. By closing the charging case, the headsets get in contact and are charged in the case. The LEDs (1) of the headsets light up red during the charging process. When fully charged, the LED‘s (1) turns off.

Charging the case
The battery of the case can be charged directly via the Micro USB port, or via the wireless charging pad. The charge status indicator of the Etius (8) shows the charge of the battery in 25%, 50%, 75% and 100% steps respectively.

Charge via USB:
Connect the USB Type-C™ cable, included with the headset, to the charging case and to a power supply or USB port on a computer to charge the battery of the case.

Wireless charging:
Connect the charging cable to the Micro USB input of the wireless charging pad (9) and a travel charger or USB port of a computer. The red LED lights up as soon as the pad is supplied with power. Place the case with the back centered on the charging pad. The blue LED indicates that the case is charging.

Switching On/Off

Switch on : Tap and hold the multifunction sensor (2) for about 2-3 seconds.
Switch off: Tap and hold the multifunction sensor (2) for about 5-6 seconds.

Note : Both headsets switch on and off automatically when they are removed or inserted from the case. When Jive is switched on, the white LED (1) flashes until it is connected. During this time it will try to connect to the last connected device.

Pairing
The Jive Headset has to be paired with a Bluetooth® device before use. The headset LED will blink white when it‘s ready to pair.

Take out the Headsets from the charging case. They will automatically power on and pair with each other. Now one of them switches to pairing mode to connect to the Phone.
Search for “Jive” on your Bluetooth® device and select it to pair the headset with your device. When properly connected, the LED
blinks white and turns off after pairing has been successful.

Note : If the Headset does not find a Bluetooth® capable device, it switches itself off after approx. 3 minutes.

Note:

When the headset is placed in the charging case, the connection is interrupted. As soon as the headset is removed, the headset automatically reconnects.
If the connection is interrupted, the multifunction sensor must be pressed to reconnect.

Music Control
All control commands are executed with the multifunction sensor (2).

Play/Pause: Tap the multifunction sensor on one of the two headsets once.

Skip Backwards: Tap the multifunction sensor of the left head 2 times.

Skip Forwards: Tap the multifunction sensor of the right headset 2 times.

Hands-free control
Answer/Hang up Call: Tap the multifunction sensor (2) once.

Reject call: Hold the multifunction sensor (2) for one second when the call comes in.

Re-Dial: When in standby, tap the multifunction sensor 4 times. Your phone will call the last dialed number. Voice dial /Voice Command: When in standby, tap and hold the multifunction sensor for 2 seconds. A „Bip“sound and voice control is activated.

Volume setting:

To increase the volume , tap the multifunction sensor (2) on the right-hand headset 3 times.
To decrease the volume, tap the multifunction sensor (2) on the left-hand headset 3 times.

Note : Rarely does it happen that the headset‘s super bass is clipping by mobile phone settings. In this case, use the „Normalise“ function (also known as „Adjust volume“) in the audio settings of your phone.

Safety advice

Do not use the headset at high volume for prolonged periods of time.
Be careful not to use headsets in potentially dangerous situations.
Do not use the headset while operating a vehicle.
Never open the device.
Never immerse the device in water, always protect it from moisture.
Disconnect electronic devices fro the power when Disconnect electronic devices from the power when not using them for longer time

Wireless Charger:

Do not open the charger
Do not expose the charger to water and protect it against humidity
Do not use brute force when connecting the adapter.
Disconnect electronic devices from the power when not using them for longer time.
Do not place cards with magnetic strips, magnetic recording media or metal objects onto the charging area or between this and your Headset box; no charging will take place and can lead to overheating!
Individuals who wear a pacemaker should maintain a sufficient distance between the device and their pacemaker. If in doubt, consult your treating physician.
This product may interfere with the proper functioning of medical equipment. Consequently, do not use device in hospitals and other medical facilities.
Never use the product if signs of damage are visible.