beamZ WHIRLWIND 3-in-1 LED Effect DMX User Guide
- June 6, 2024
- beamZ
Table of Contents
beamZ WHIRLWIND 3-in-1 LED Effect DMX
POWER SUPPLY
On the label on the backside of the unit is indicated on this type of power supply must be connected. Check that the mains voltage corresponds to this, all other voltages than specified, the light effect can be irreparably damaged. The product must also be directly connected to the mains and may be used. No dimmer or adjustable power supply.
WARNING
Always connect the unit to a protected circuit (circuit breaker or fuse). Make
sure the unit has an appropriate electrical ground to avoid the risk of
electrocution or fire.
RIGGING
The unit may be set up on a stable and even surface. By means of the fixing
facilities of the baseplate, the unit can also be mounted upside down to a
truss, see below picture. For fixing, certified clamps with correct save
working load are required. According to the figure, the quick lock bolts of
the omega brackets are placed into the openings provided in the base plate and
turned clockwise until they lock (to the stop). The mounting place must be of
sufficient stability and be able to support a weight of 10 times of the unit’s
weight. Secure the unit with a safety cable so that it cannot fall down.
When carrying out any installation, always comply European and national
guidelines concerning rigging, truss and all other safety issues. Always let
the installation checked out by an authorized dealer !
DMX512 CONTROL
If you are using a standard DMX controller, you can connect the DMX output of
the controller directly to the DMX input of the first unit in a DMX chain.
Always connect the output of one unit with the input of the next unit until
all units are connected. 
CAUTION
At the last unit, you must close the DMX line with a terminating resistor.
Take an XLR connector and solder a 120 Ohm resistor between signal (-) and
signal (+) and connect it to the DMX output of the last unit in the line
.
REMOTE CONTROL
| BUTTON | FUNCTION | **** |
|---|---|---|
| ON | ON | |
| OFF | OFF | |
| OMX | DMX Mode | |
| AUTO | Auto Running Mode | |
| SPEED+ | Auto Running Speed up | |
| SPEED- | Auto Running Speed down | |
| VOICE | Sound Control Mode | |
| MIC+ | Sound Sensitive + | |
| MIC- | Sound Sensitive – | |
| 1 | Red | |
| 2 | Green | |
| 3 | Blue | |
| 4 | White | |
| 5 | UV |
CONTROL MENU
| MENU | DESCRIPTION | |
|---|---|---|
| A000-AS12 | DMX address setting | |
| AL1-AL9 | I n t e r n a l p r o | |
| g r a m 1 – 9 | Auto program | |
| SLl- SL9 | Internal sound program | S o un d p |
r o g r a m , 1 – 9 m e a n s s e n s i t i v e
DMX CHANNELS
| CHANNEL | FUNCTION | VALUE | DESCRIPTION |
|---|---|---|---|
| 1 | Pan | 000-255 | 0-540degree movement |
| 2 | Tilt | 000-255 | 0 – 1 8 0 d e |
g r e e m o v e m e n t
3| Pan/Tilt Speed| 000-255| Pan/Tilt Speed from fast to
slow
4| Lens Wheel Rotation| 000 – 1 2 7|
0-360degree rotate
| | 1 2 8 – 1 9 1| Forward endless rotate
from slow to fast
| | 1 9 2 – 2 5 5| Reverse endless rotate
from slow to fast
5| Dimmer| 000-255| Linear dimmer from dark to brighter
6| Strobe| 000-009| No function
| | 0 1 0 – 25 5| Strobe from slow to fast
7| Red| 000-255| Red dimmer from dark to brighter
8| Green| 000-255| Green dimmer from dark to brighter
9| Blue| 000-255| Blue dimmer from dark to brighter
10| White| 000-255| White dimmer from dark to brighter
11| Mode| 000-050| C H 1 – C H 1
0 V a l i d
| | 0 5 1 – 1 5 0| Random Auto Running
| | 1 5 0 – 25 5| Sound Control
12| Reset| 000-250| None
| | 2 5 1 – 2 5 5| Reset after 3s
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>