CMP 25503-500-000 Brilliant Wonders 1.5 Inch LED Light Instruction Manual
- June 6, 2024
- CMP
Table of Contents
CMP 25503-500-000 Brilliant Wonders 1.5 Inch LED Light Instruction Manual
25503-500-000
25503-520-000 (P-Style and H-Style)
25503-560-000 (P-Style and H-Style)
Cord Lengths Available:
25’, 50’, 100’, 150’
LED WATERFALL | LED BUBBLER | LED LIGHTS | LED LAMINAR
1. IMPORTANT WARNINGS & SAFETY INSTRUCTIONS
2. INSTALLATION INSTRUCTIONS
STEP 1
The light must be installed in or on a wall of the pool (or water feature)
with the top of the lens opening no less than 4 inches (10.16cm) below normal
water level of the pool. For vertical installations on benches, swim outs and
fountains the depth of the light underwater must still be no less than 4
inches.
NOTE: Requires the use of a 1.5″ threaded wall fitting.
NOTE: 12″ minimum of 1.5″ pipe to accommodate the LED Light. Then 1″ pipe to control box with sweeps only, no 90° bends.
STEP 2
Install supplied 2-conductor electric cord through the conduit outlet of the
wall into the conduit and up to the location of the 12VAC pool/spa
transformer. Cut off excess cord installing appropriate service length.
Allow 18″-24″ extra slack in the cord on the 12VAC pool transformer end for future service of the LED light.
An example of an approved pool transformer is the Intermatic model PX-100 or PX-300. Refer to Wire Gauge and Wire Length guide for proper wire gauge size in reference to the use of Junction Box installations.
NOTE: Brilliant Wonders 1.5” LED Light can be used with any UL Listed, outdoor rated, 12VAC transformer provided the wattage and amperage is not exceeded by the total wattage and amperage in use.
WIRING CONNECTION TO TRANSFORMER
A Red wire is used with the Brilliant Wonders Controller. If another timer or
switch is installed, there may not be a red wire. If this is the case, follow
this wiring structure:
Black = Hot
White = Neutral
Green = Ground
STEP 3
Thread the Faceplate into the 1.5″ Threaded Wall Fitting using the included
Installation Tool until snug (do not over tighten). Tighten set screw using a
2mm Allen wrench (not included).
STEP 4
Connect male and female electrical cord connections and thread together until
snug. Install light into Faceplate by snapping included Installation Tool into
the 4 rectangle holes in the LED Lens and then gently pushing in the LED Light
while twisting the Installation Tool clockwise until it clicks into place.
Pull Installation Tool straight out to disconnect it from the LED lens.
WINTERIZATION CLAUSE
Pool water level must be drained 12″ below light(s) position in pool wall. It
is recommend that the lights be loosened from their Wall Fittings to allow
drainage of water that might have accumulated inside the conduit. It is
recommended to disconnect cord connections and remove the 1.5″ LED Light
completely for the winter. Consult your local swimming pool professional for
proper local area winterization processes.
LIGHT IS SERVICEABLE
Do not disassemble any part of the Brilliant Wonders 1.5” LED Light body. Only
remove
cord at connection between male and female connectors.
3. OPERATION INSTRUCTIONS
When syncing multiple LED light products, color shows will match
NOTICE but cycle timings may vary.
CMP/J-STYLE COLOR SELECTION AND SYNC INSTRUCTIONS
The CMP/J-STYLE Brilliant Wonders 1.5″ LED Light is preprogrammed with the following color sequence:
To operate the light and change colors:
- Turn the light ON. The first time the light is turned on, the color sequence will begin with Alpine White. To change color, turn light OFF then back ON within three (3) seconds. Continue turning OFF and ON until the desired light color mode is reached.
- When the light is turned off for more than seven (7) seconds, it will remain in the color mode that was currently active when the light was turned off.
- To RESET the light to the beginning color sequence (Alpine White), turn the light OFF, wait four (4) to six (6) seconds, then turn the light ON.
H-STYLE COLOR SELECTION AND SYNC INSTRUCTIONS
The H-STYLE Brilliant Wonders 1.5” LED Light is preprogrammed with seventeen
light modes:
To operate the light and change colors:
- The H-STYLE Brilliant Wonders 1.5” LED Light is operated through power-cycling; a method of changing modes which requires no special controller or interface. To activate the light simply turn the power switch ON. To advance to the next programmed light mode, turn the switch OFF then back ON within ten (10) seconds. Whenever the light has been off for more than sixty (60) seconds, and it is first turned on, it will come on white for 15 seconds, then go back to the last programmed light mode it was running before being powered off.
P-STYLE COLOR SELECTION AND SYNC INSTRUCTIONS
The P-STYLE Brilliant Wonders 1.5” LED Lights can be controlled using a
standard wall-mount light switch. Multiple lights can be connected via a
junction box to a single switch so that all lights can be switched ON and OFF
together. P-STYLE Lights are controlled by cycling the AC power from a
standard wall switch. By turning the switch ON and OFF a specific number of
times, the light activates one of the seven (7) light show modes, fixed
colors, and enables the “Hold” and “Recall” feature.
The P-STYLE Brilliant Wonders 1.5” LED Light is preprogrammed with seven light show modes (1-7) and five fixed color modes (8-12). For saving color effects during the “show” modes the light also includes and “Hold” and “Recall” feature (13-14).
Example to operate the light and change to “California Sunset” show mode:
- Turn the light switch ON and OFF six (6) times.
- During the ON/OFF switching process, no illumination will occur, then a white light will momentarily illuminate.
- The white light will immediately be followed by the selected “California Sunset” mode.
Hold and Recall Features Example:
- Use the “Hold” feature to capture a unique color effect while “Romance Mode” is active.
- Turn switch on and off thirteen (13) times.
- Saved color effect is displayed.
- From any light show or fixed color mode…
- Turn switch ON and OFF fourteen (14) times to activate last saved color effect.
- Saved color effect is displayed.
4. AVAILABLE ACCESSORIES
For the most recent instructions, videos and product information visit www.c-m-p.com
FOR PRODUCT IMAGES, VIDEOS, LITERATURE AND UP-TO-DATE INSTRUCTIONS VISIT
WWW.C-M-P.COM
ON YOUR COMPUTER OR MOBILE DEVICE
CUSTOM MOLDED PRODUCTS | 36 HERRING ROAD, NEWNAN, GA 30265 | WWW.C-M-P.COM
Read More About This Manual & Download PDF:
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>