Milesight UR32 Industrial Router Pro Series User Guide

June 6, 2024
Milesight

Milesight UR32 Industrial Router Pro Series

Milesight-UR32-Industrial-Router-Pro-series

Packing List

Before you begin to install the UR32 router, please check the package contents to verify that you have received the items below.

Milesight-UR32-Industrial-Router-Pro-series-1

If any of the above items is missing or damaged, please contact your sales representative.

Hardware Introduction

Overview

Milesight-UR32-Industrial-Router-Pro-series-2

Dimensions (mm)

Milesight-UR32-Industrial-Router-Pro-series-3

Serial & IO & Power Pinouts

PIN| RS232

/RS485*

| DI| DO| Description
---|---|---|---|---
1| —| —| OUT| Digital Output
2| —| IN| —| Digital Input
3| GND| GND| —| Ground
4| —|  | COM| Common Ground
5| RXD/B| —| —| Receive Data
6| TXD/A| —| —| Transmit Data
PIN| Description| Wire Color
---|---|---
7| Positive| Red
8| Negative| Black

LED Indicators
LED Indication Status Description
POWER Power Status Off The power is switched off
On The power is switched on

SYSTEM

|

System Status

| Green Light| Static: Start-up
Blinking slowly: the system is running properly
Red Light| The system goes wrong

SIM

|

SIM Card Status

| Off| SIM1 or SIM2 is registering or fails to register (or there

are no SIM cards inserted)

Green Light

| Blinking slowly: SIM1 has been registered and is ready

for dial-up

Blinking rapidly: SIM1 has been registered and is

dialing up now

Static: SIM1 has been registered and dialed up

successfully

Orange Light

| Blinking slowly: SIM2 has been registered and is ready

for dial-up

Blinking rapidly: SIM2 has been registered and is

dialing up now

Static: SIM2 has been registered and dialed up

successfully

Signal Strength|

Signal 1/2/3

| Off| No signal
Green Light| Static/Off/Off:  weak  signals  with  1-10  ASU  (please

check if the antenna is installed correctly, or move  the

      antenna to a suitable location to get better signal)

Static/Static/Off: normal signals with 11-20 ASU

(average signal strength)

Static/Static/Static: strong signals with 21-31 ASU

(signal is good)

Reset Button
Function Description
SYSTEM LED Action

Reset

| Blinking| Press and hold the reset button for more than 5 seconds.
Static Green →

Rapidly Blinking

| Release the button and wait.
Off → Blinking| The router is now reset to factory defaults.

Ethernet Port Indicator
Indicator Status Description

Link Indicator (Orange)

| On| Connected
Blinking| Transmitting data
Off| Disconnected

Hardware Installation

Environmental Requirements
  • Power Input: 9-48 VDC (48 VDC is needed for PoE output)
  • Power Consumption: Typical 1.9W (Max 2.4 W)
  • Operating Temperature: -40°C to 70°C (-40°F -158°F)
  • Relative Humidity: 0% to 95% (non-condensing) at 25°C/77°F

SIM Card/Micro SD Card Installation

  • Unscrew the cover of the SIM card then take it off.
  • Put SIM card/Micro SD into the slot and screw it up.
Antenna Installation

Rotate the antenna into the antenna connector accordingly. The external antenna should be installed vertically always on a site with a good signal.

Router Installation

The router can be placed on a desktop or mounted to a wall or a DIN rail.

Wall Mounting (Measured in mm)

Use 4 pcs of M3 × 6 flat head Phillips screws to fix the router on the wall.

DIN Rail Mounting (Measured in mm)

Use 2 pcs of M3 × 6 flat head Phillips screws to fix the mount clip to the router, and then hang the device to the DIN rail. The width of DIN rail is 3.5cm.

  • Recommended torque for mounting is 1.0 N·m, and the maximum allowed is 1.2 N·m.

Log in the Web GUI of Router

Please connect PC to LAN port of UR32 router. PC can obtain an IP address, or you can configure a static IP address manually. The following steps are based on Windows 10 operating system for your reference.

  • IP Address: 192.168.1.1
  • Username: admin
  • Password: password

Go to “Control Panel” → “Network and Internet” → “Network and Sharing Center”, then click “Ethernet” (May have different names).

Milesight-UR32-Industrial-Router-Pro-series-11

Go to “Properties” → “Internet Protocol Version 4(TCP/IPv4) ”, select “Obtain an IP address automatically” or “Use the following IP address”, then assign a static IP manually within the same subnet of the device.

Milesight-UR32-Industrial-Router-Pro-series-12

Open a Web browser on your PC (Chrome is recommended), type in the IP address 192.168.1.1, and press Enter on your keyboard.

Enter the username, password, and click “Login”.

Milesight-UR32-Industrial-Router-Pro-series-13

When you login with the default username and password, you will be asked to modify the password. It’s suggested that you change the password for the sake of security. Click “Cancel” button if you want to modify it later.

After you login the Web GUI, you can view system information and perform configuration on the router.Milesight-UR32-Industrial-Router-Pro-
series-15

Network Configuration

This chapter explains how to connect UR32 to network via WAN connection or cellular.

Ethernet WAN Configuration
  • Go to “Network > Interface > Port” to change LAN1 to WAN port.Milesight-UR32-Industrial-Router-Pro-series-16
  • Go to “Network > Interface > WAN” to select connection type and configure WAN parameters, click “Save & Apply” button to make the changes take effect.Milesight-UR32-Industrial-Router-Pro-series-17
  • Connect WAN port to another network devices like modem.
  • Go to “Network > Interface > Link Failover” to rise the WAN priority to 1.
  • Open your preferred browser on PC, then type any available web address into address bar and see if it is able to visit Internet via UR32 router.Milesight-UR32-Industrial-Router-Pro-series-18

Cellular Connection Configuration

Take inserting SIM card into SIM1 slot as an example; please refer to the following detailed operations.

  • Go to “Network > Interface > Cellular > Cellular Setting” to configure APN, PIN code or other cellular info, click “Save” and “Apply” to save the configuration.Milesight-UR32-Industrial-Router-Pro-series-19
  • Go to “Network > Interface > Link Failover” to enable SIM1 and rise link priority of SIM1.Milesight-UR32-Industrial-Router-Pro-series-20
  • Click to configure ICMP ping detection information.
  • Click “Status > Cellular” to view the status of the cellular connection. If it shows “Connected”, it means SIM1 has dialed up successfully. On the other hand, you can check the status of SIM indicator. If it keeps on green light statically, it means SIM1 has dialed up successfully.Milesight-UR32-Industrial-Router-Pro-series-22
  • Open your preferred browser on PC, then type any available web address into address bar and see if it is able to visit Internet via UR32 router.

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals