dji AST01 Mic Wireless Kit Instructions
- June 6, 2024
- DJi
Table of Contents
dji AST01 Mic Wireless Kit
Safety at a Glance
Please read this entire document and visit https://www.dji.com/mic to view the user manual, other documents, and the tutorial videos with the most current instructions and warnings. Failure to read and follow instructions and warnings may result in personal injury, damage to your DJI OSMOTM product, or other objects in the vicinity. This document and all other collateral documents are subject to change at the sole discretion of DJI OSMO. By using this product, you hereby signify that you have read and agreed to abide by the terms and conditions of this document. You agree that you are solely responsible for your own conduct while using this product and for any consequences thereof. This product is not intended for use by children without direct adult supervision.
WARNING
- DJITM Mic contains magnets. Keep the DJI Mic away from magcards, IC cards, hard disks, RAM chips, implantable medical devices such as pacemakers, and other devices to avoid interference.
- DO NOT listen at a high volume for an extended period using monitor earphones. Otherwise, you may experience possible hearing damage.
- DO NOT allow the product to come into contact with any kind of liquid. DO NOT leave the product out in the rain or near a source of moisture. DO NOT drop the product into water. If the inside of the battery comes into contact with water, chemical decomposition may occur, potentially resulting in the battery catching on fire, and may even lead to an explosion.
- Put out any product fire using water, sand, fire blanket, or a dry powder fire extinguisher.
- The product should be used in temperatures from -10º to 45º C (14° to 113° F). Use of the product in environments above 45º C (113°
- Never disassemble or pierce the product in any way or the battery may leak, catch fire, or explode.
- DO NOT drop or strike the product. DO NOT place heavy objects on the product.
- DO NOT heat the product. DO NOT put the product in a microwave oven or in a pressurized container.
- DO NOT leave the product near heat sources such as a furnace or heater. DO NOT leave the product inside of a vehicle on hot days. The ideal storage temperature is 22º C to 28º C (72° to 82° F).
- DO NOT store the product fully discharged for an extended period. Otherwise, it will over discharge, which will lead to permanent damage.
Specifications
Compliance Information
FCC Compliance Notice
Supplier’s Declaration of Conformity Product name: DJI MIC Model Number:
AST01/ASR01/ASB01 Responsible Party: DJI Technology, Inc. Responsible Party
Address: 201 S. Victory Blvd., Burbank, CA 91502 Website:
www.dji.com
We, DJI Technology, Inc., being the responsible party, declares that the above
mentioned model was tested to demonstrate complying with all applicable FCC
rules and regulations. This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) This device must accept any interference
received, including interference that may cause undesired operation. Any
changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment. This
equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
RF Exposure Information
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. End user must follow the specific operating
instructions for satisfying RF exposure compliance. This transmitter must not
be co-located or operating in conjunction with any other antenna or
transmitter. The portable device is designed to meet the requirements for
exposure to radio waves established by the Federal Communications Commission
(USA). These requirements set a SAR limit of 1.6 W/kg averaged over one gram
of tissue. The highest SAR value reported under this standard during product
certification for use when properly worn on the body.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>