VENTURE Lightings CCT and Wattage Selectable Back-Lit LED Panel User Manual

: June 6, 2024
: VENTURE

Table of Contents

UNPACKING
INCLUDED IN THIS BOX
IMPORTANT SAFETY INFORMATION
Installation Instructions for T-grid Ceiling
Electrical Wiring Instructions
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

VENTURE LIGHTING’S CCT & WATTAGE SELECTABLE
BACK-LIT LED PANEL FIXTURES

USER MANUAL

Before You Begin
READ THESE INSTRUCTIONS COMPLETELY AND CAREFULLY

UNPACKING

Unpack and carefully examine the product.
Report any damage and save all packing materials if any part(s) were damaged during shipping.
Do not attempt to install or use this equipment if it is damaged.

INCLUDED IN THIS BOX

LED Backlit Panel Fixture.
The driver comes prewired with 1 black input lead (hot), 1 white input lead (neutral), 1 green ground lead, 1 purple Dim (+) lead, and 1 pink Dim (-) lead.
Installation

WARNING – RISK OF FIRE, ELECTRIC SHOCK, INJURY, OR PROPERTY DAMAGE

Failure to follow these instructions or altering equipment could result in injury or damage and void warranty. Venture assumes no liability for injury, damages or losses of any kind that may arise from the improper, careless, or negligent installation, handling or use of this product.
This equipment must be installed and serviced per applicable codes and ordinances by qualified personnel (ex. licensed electrician) familiar with the operation of the product and any hazards involved.
Disconnect power to the equipment and allow to cool before installing or
Handle sharp edges To prevent wiring damage, do not expose wiring to sharp edges.
Verify that all electrical connections have been properly made and the fixture is grounded to avoid potential electrical
It is the responsibility of the installer to confirm the proper input voltage is used with this
Do not handle energized equipment when hands are wet when standing on wet surfaces, or in
This fixture must be mounted securely to a ceiling or structure to support the
This fixture may be provided with a factory-installed battery backup option. Refer to the battery backup user manual for installation and operating instructions.

SUPPLIER’S DECLARATION OF CONFORMITY (SDoC)

This equipment complies with the limits for a Class A digital device, pursuant to Part 15 Subpart B of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial, industrial or business environment.
This equipment complies with the limits for Class A lighting equipment, pursuant to Innovation, Science, and Economic Development Canada’s CAN ICES-005 (A) / NMB-005 (A).

For warranty information refer to https://www.venturelighting.com/resources/warranties.html.

IMPORTANT SAFETY INFORMATION

Operating temperature: -25°C to +40°C (-13°F to +104°F).
Suitable for use in damp and dry locations only.
Type IC Rated for direct insulation contact.
Any vapor barrier used with this equipment shall be rated at a minimum of 90°C (194°F).
All wiring and connectors used with this equipment shall be rated at a minimum of 90°C (194°F).

Installation Instructions for T-grid Ceiling

NOTE: Access above the T-grid ceiling is required.

STEP 1: Ensure the T-grid ceiling is rated for the fixture weight (including all optional accessories such as a battery backup). If required by applicable codes and ordinances, use proper hanger wire (not provided) to support the fixture to the building structure from at least two opposite corners (use the holes provided in the integral T-bar support brackets).

STEP 2: The fixture backplate includes integral T-bar support brackets for installation onto standard 15/16” T-grid ceilings or narrow 9/16” T-grid ceilings. Bend each of the T-bar support brackets on the fixture backplate by 90 degrees, making it vertical to the backplate. Then bend the top portion of each T-bar support bracket by 90 degrees so that it overhangs the edge of the fixture.

STEP 3: Place the fixture onto the T-grid ceiling (see fig 1), ensuring each of the T-bar support brackets are positioned over the T-bar rails (see fig 2).

Note: Optional surface mount, drywall, and suspension kits are available (sold separately).

PRODUCT CARE – It may become necessary to clean the outside of the refractor/lens. The refractor/lens should be washed in a solution of warm water and any mild, non-abrasive detergent, rinsed with clean water, and wiped dry.

Electrical Wiring Instructions

STEP 1:
Disconnect power to the equipment and follow proper lockout/Tagout procedures before beginning installation or maintenance.
STEP 2:
Remove the driver wiring junction box cover (screwdriver required).
STEP 3:
Remove the desired knock-out(s) and connect the input supply conduit to the junction box with the appropriate connector(s).
STEP 4:
Connect the fixture ground wire (Green) to the system ground wire.
Connect the input supply wires to the Line (Black) and Neutral (White) input leads of the LED driver.
For thru-wiring to another luminaire, utilize a second knockout and connect to Line (Black), Neutral (White) and Ground (Green) input leads of the LED driver.
STEP 5:
Dimming Wiring:
Use of the 0-10VDC dimming functionality is optional. If not using the dimming functionality, the DIM+, and DIM- ports must remain open (no connection). DO NOT connect the Driver Dim+ and the Driver Dim- together as the fixture will not operate as desired.
Refer to the specific dimmer control instructions for additional wiring information.
Connect the LED Driver Dim+ wire to the Dimmer Control D+ wire (purple wire, not provided).
Connect the LED Driver Dim- wire to the Dimmer Control D- wire (pink wire, not provided).
The polarity of these dimming connections is important to ensure the fixture performs as desired.
STEP 6:
Ensure all wiring and electrical connections are positioned correctly to avoid any damage and replace the driver wiring junction box cover (screwdriver required).
STEP 7:
Position the CCT (color temperature) and Wattage selection slide switches (located on the external side of the driver) for the desired settings.
STEP 8:
Switch on the power.