NTI ST-FOHD-SC50 HDMI Extender via One SC Multimode Fiber Optic Cable User Manual
- June 6, 2024
- NTI
Table of Contents
NTI ST-FOHD-SC50 HDMI Extender via One SC Multimode Fiber Optic Cable
Introduction
The XTENDEX® HDMI Extender via Fiber Optic Cable locates an HDMI display up to 980 feet (300 meters) away from a video source using a simplex SC multimode fiber optic strand. Each extender consists of a transmitter that connects to a video source and a receiver that connects to a display.
- Signal transmission via single-strand multimode SC fiber optic cable – no RF interference.
- Supports HDTV resolutions to 1080p and computer resolutions to 1920×1200.
- Compact and durable design — allowing for easy connection and placement.
- HDMI features supported:
- 36-bit Deep Color
- Dolby TrueHD, DTS-HD Master Audio, Dolby Digital, and DTS
- Bandwidth up to 4.46 Gbps
- HDCP compliant.
- Supports the DDC2B protocol.
- Supports full 60fps video.
- No software to install.
- Cables can be installed in conduit prior to extender installation.
Material Supplied with this kit:
ST-FOHD-SC50 Transmitter and Receiver Unit 1- Power supply- In:100 to 240V,
50/60Hz; Out: DC 5V, 2A or 3A URL Slip with Web location of this manual
Available Material sold separately:Use a simplex SC multimode 50-micron fiber
optic cable (FIBER-S-SCSC-50-xxM) or 62.5µm multimode (OM2 or better Use a
simplex SC multimode 50-micron fiber optic cable (FIBER-S-SCSC-50-xxM) or
62.5µm multimode (OM2 or better.
Installation
this extender system is composed of two individual units, the Transmitter and the Receiver, interconnected by fiber optic cable. A simplex SC multimode 50-micron or 62.5µm (OM2 or better recommended) fiber optic cable is required for extension up to 980 feet (300 meters).
- Connect the Transmitter to the HDMI port on the video source device.
- Connect the Receiver to the HDMI port on the video display device.
- Connect the multi-mode SC type 1 channel standard fiber optic cable from Transmitter to the Receiver.
- Connect the included +5VDC power supply to the receiver.
- The Green Power LED indicator on the Transmitter and Receiver will illuminate after all connections are complete. LED ON = Power is being supplied and signals are transferring between the Transmitter and Receiver LED Blinking = Power is being supplied but signals are not transferring between the Transmitter and Receiver. (Connections are not complete.)
Note: The minimum bend radius of the fiber optic cable is 75mm (3″)
Specifications
Transmitter and Receiver Connectors| · One male HDMI connector for source/display.
· One simplex SC fiber optic port for sending/receiving high-definition video/audio signals and DDC signal.
· HDCP compliant.
· Supports full 60fps video
---|---
Supported Video Resolutions| Supports HDTV resolutions to 1080p and computer
resolutions to 1920×1200 @ 60Hz up to 980 feet (300 meters)
EDID| Pass through
HDCP| Compliant
Operating Temperature| 32 to 122°F (0˚ to 50˚C )
Storage Temperature| -4 to 158°F (-20˚ to 70˚C)
Humidity| 20-80% Operating, 10-90% Storage Relative Humidity Non-condensing
Power -Local| Powered by attached video source
Power-Remote| · Input: 100 to 240 VAC at 50 or 60Hz via AC adapter (US,
UK, EU or AUS adapter included.)
· Output: 5VDC, 2A or 3A
Cables| Use a simplex SC multimode 50-micron fiber optic cable (FIBER-S-SCSC-50- xxM) or 62.5µm multimode (OM2 or better recommended) fiber optic cable to extend the receiver from the transmitter up to 980 feet (300 meters).
· Cables not included.
Max Distance| 980 feet (300 meters) over 50µm or 62.5µm multimode SC fiber
optic cable.
Dimensions (Local and Remote) WxDxH| 3.33×1.31×0.46 in (85x33x11 mm) with
8.5-inch (216-millimeter) male HDMI cable attached
Power Consumption| Transmitter: 1.3W (Max.), Receiver: 1.1W (Max.)
Eye Safety| CLASS 1 LASER PRODUCT-IEC60825-1:2007 (2nd Edition)
Approvals| CE, UL, FCC, TAA compliant
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>