NTI ST-IPUSB4K-LC HDMI HDBaseT KVM Extender 4Kx2K User Manual

NTI ST-IPUSB4K-LC HDMI HDBaseT KVM Extender 4Kx2K

Thank you for purchasing this product. For optimum performance and safety, please read the instructions carefully and keep the manual for future reference.

Important safety notice

Please read below safety instructions carefully before installation and operation:

• Please pay attention to all the warnings and hints on this device.
• Do not expose this unit to rain, moisture and liquid.
• Do not put any stuff into the device.
• Do not repair or open this device without professional people’s guidance.
• Make sure good ventilation openings to avoid product overheating damage.
• Shut off the power and make sure the environment is safe before installation.
• Do not plug in/out the connected cables when it is in use.
• Make sure the specification matched if using 3rd party DC adapters.

Introduction

This HDMI KVM extender consists of a transmitter (TX) and a receiver
(RX). The product is network-mediated and uses amplification and extension technology. The transmitter and receiver are extended by a single network cable. The HDMI signal can be extended to 100 meters uncompressed with nearly zero latency by CAT6/CAT6A/CAT7 cable.
It supports EDID pass back, supports one-to-many connection through the switch, and the resolution supported is up to 4KX2K@30Hz. It supports the KVM function and allows access to a computer system from a remote console by USB mouse and keyboard. It is useful for control and security purposes. Therefore it is widely used in the command centers, data control centers, military, banks, governments, enterprises,s, etc.

Features

1. Transmitter support one HDMI loop-out
2. HD uncompressed and nearly zero latency transmission
3. Support distance up to 100m via CAT6/6A/7
4. Support one-to-many connection through the switch
5. Support KVM function, remote control conveniently
6. Support EDID pass back
7. Resolution supported is up to 4Kx2K@30Hz
8. Plug and play, easy installation

Package Contents

Installation Requirements

1. Source equipment :
   HDMI source device (computer graphics card, DV D, PS3, HD monitoring equipment etc).

2. Display devices:
   With HDMI INPUT port, SDTV, HDTV, projector

3. Network cables:
   UTP/STP CAT6/CAT6A/CAT7 network cables, which following the standard of IEEE-568 B

Panel Description

Transmitter (TX)

1. HDMI INPUT: Input HDMI signal
2. HDMI OUTPUT: Output HDMI signal
3. TX: Connect with the network cable
4. PC: Input USB cable
5. DC SV: Input DCSV power
6. (!): To indicate the power status of the device
7. To indicate the connection status of the devices
8. RESET: Restart the device

Receiver (RX)

Installation Procedures

1. To make a Cat6/6A/7 network cable
   Follow the standard of IEEE-5688:

2. Connection

3. Connection instruction

4. Connect the PC to the HDMI input of the transmitter (TX), If needed to loop out, connect the local display device to the H DMI output of the TX.

5. Connect the PC to the USB port of the transmitter (TX).

6. Connect HDMI output to HDMI display device.

7. Connect the keyboard d/mouse to the USB port of the receiver (RX).

8. Connect the transmitter and the receiver with the internet cable.

9. Plug the power supply into the device to get started.

Note: When using a one-to-many connection through the switch, press the ” US B” button to switch the receiver to be use d. The dis p I a y connected to the receiver will display the word “USB owner” . The transmitter will automatically match the last receiver.

Note: When using a one-to-one connection, after replacing the display device, if you want to match the EDID of the display device, press the EDID button. The screen will show “Updated EDID”. Then press the “USB” button to confirm.

FAQ

Q: Why does the screen have no output?

1. A: 1) Please check and make sure the power supply and all cables are connected well.
2. Please check and make sure you have chosen the right H DMI port of all the devices.
3. Please check and make sure there is HDMI signal to be fed into the transmitter and the display is turned on.

Q: Why does the display only have the sound but no synchronous image display?
A: Please set as follows: Right-click on the blank space on the desktop- “Screen resolution” (Windows 7) or “Display settings” (Windows 10)- “Multiple displays” – “Extend these displays”

Q: How do I do if the power indicator is on but the connection indicator is off?

1. A: Please check the network cable is well-connected to the transmitter and the receiver.
2. Restart the transmitter or the receiver.

Q: Why does the keyboard/mouse have no response after connecting to the RX?

1. A: Please check and make sure the keyboard/mouse is well-connected and electrified.
2. Press the “USB” button on the receiver, and check if there is the word “USB owner” displayed on the screen.
3. Restart the receiver.

Q: Why does the output image have the snow point or unstable?

1. A: Please change the HDMI cable between the PC and the transmitter, or use a shorter HDMI cable for testing.
2. Please check and make sure the network cable you are using is CAT6/CAT6A/CAT7.

Specification

HDMI

performance and interface

| HDMI complian ce| HDMil.4
HDCP compliance| HDCP 1.4

HDMI resolution supported

| 800 x600@60H,z     1 0 24×768 @60H z,

1 280 x720 @60H, z    1280×800@60H , z

1280xl  024 @60H, z    1 440×900 @60H z,

1 680 xl 050@60H, z     1920xl 080 @60 H,z

2560 xl 080 @60H, z    3840×21 60 @30H,z

4096×2160@30Hz

Supports audio formats| PCM, LPCM, Dolby, DTS
Maximum transfer rate| 10.2Gbps
Input and output TMDS signal| 0.7~l.2Vp-p(TMDS)
Input and output DDC signal| SVp-p{TTL)
Input cable length supported| Sm(AWG24)
Output cable length supported| Sm(AWG24)
Transmission length| ****

CAT6/ 6A/7

| 100m
Protection level| ****

Electrostatic protection of the whole machine

| la Contact discharge level 3 lb Air discharge level 3 Standard: IEC61000 -4-2

Operating environment

| Working temperature| 0 ~60°(
---|---|---
Storage temperature| -40 ~70°c
Humidity (no condensation)| 0~90%

Body properties

| Dimension| 132.37(L) x 89.70(W) x 24.90(H) mm
Material| Iron alloy material+crystal panel
Processing technology| Sandblasting
Color| Black
Weight| TX:320g      RX:310g

Power Supply
The ST-IPUSB4K-LC comes with two power supplies, one for the Sender, one for the Receiver. The ST-IPUSB4K-R-LC is a Receiver only and comes with a single power supply. The type of power supply provided depends on the model ordered, which determines the type of plug that will be included to connect to your power source.

Mode l                                   Power Cord Plug Supplied

ST-IPUSB4K-LC| US NEMA 1-lSP
ST-IPUSB4K-LIU| Euro p lu g CEE 7 /16
ST-IPUSB4K-LUCK| UK BS1363
ST-IPUSB4K-LCAU| AS/NZS 3112
ST-IPUSB4K- LCU NVxx| US NEMA 1-lSP with country-specific universal

power plug adapter

The ST-IPUSB4K-LCUNVxx will include a universal power plug suitable for the power connections found in the country the power supply was ordered for (xx).

xx **Country ****xx ****Country**

ZA| South Africa| RU| Russia
IT| Italy| IL| Israel
CH| Switzerland| AU| Australia
IN| India| EU| Europe
UK| Un it ed Kingdom| DK| Denmark

Disclaimer
The pictures on the user manual are just for reference, and there may be some slight differences from the real products. We reserve the right to make changes without further notice to a product or system described herein to improve reliability, function or design.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>