EAGLE G009MG Set of 6 White LED Puck Lights with PSU Instructions

June 6, 2024
EAGLE

G009MG
Eagle Set of 6 White LED Puck Lights
with PSU

CONGRATULATIONS ON YOUR PURCHASE
Thank you for purchasing this Eagle Puck Light Kit. Please read these instructions carefully and leave them with the user of the product for future reference. If the product is sold on then the instruction/manual should pass on as well.

BEFORE USE
You must inspect the product and all accessories including any cables, leads, and power supply for signs of damage. If the product is damaged, DO NOT use it, and contact your supplier immediately.

PRODUCT SAFETY

  • Children shall not play with the unit.
  • Cleaning and user maintenance shall not be made by children without supervision.
  • Please ensure the device is switched off when not in use.
  • Do not use the device for other than its intended purpose.
  • Do not use this product in bathrooms or other very hot or humid locations.
  • Periodically check this product and its power supply for damage. If any is detected do not use it and contact your supplier.
  • Do not leave this product switched on while unattended.
  • The power supply MUST be kept in a well-ventilated area away from sources of heat and moisture, such as a cooker and kettles.

INCLUDED IN THE BOX

1 x 6 puck lights
1 x Power supply with inline switch
12 x Wood screws
1 x Junction box
6 x Sticky pads

**INFORMATION

**

  • The maximum lead length from the junction box to each light is 2m so try to mount the junction box in the middle of the installation allowing for a span of up to 4m.
  • While the product comes with both double-sided sticky foam pads and wood screws in most circumstances the pads on their own will usually be sufficient for permanent installation. Before using the wood screws the installer should take care to make sure they are suitable.
  • When using the sticky pads for installation make sure all surfaces are clean and clear of grease and dust.

INSTALLATION

Fix Each Puck in place using either the sticky foam pads or wood screws. If using the screws only use the two outer fixing points on the puck as per image below. Access to these can be gained by unscrewing the top of the puck and removing the plastic diffuser. This should be replaced after installation.

Wire each puck to the junction box as per the diagram below. When all of the pucks have been installed connect the power supply to the junction box and switch on.

MAINTENANCE
There are no user-serviceable parts in this product. Periodically check the product for LED failure and damage. If any of the LED’s have failed or the product is damaged in any way switch off and disconnect from the mains supply. To clean the product, switch off and disconnect from the main supply. Using a slightly damp cloth gently wipe over. Do not use bleach, solvent-based cleaners or strong detergents. These may damage the product and invalidate the warranty. If the mains lead is damaged, it must be replaced by the manufacturer or and authorized service centre.

PAT TESTING
When used in an office environment, we recommend that this product should be safety-tested yearly by a qualified electrician (PAT Tested). We recommend that it is PAT tested regularly when used in a domestic environment.

GENERAL SAFETY REQUIREMENTS
Domestic wiring must be tested periodically by a qualified electrician at least once every 10 years or at every change of occupancy. For office and retail premises, and buildings such as village halls, the wiring must be inspected at least once every 5 years. It is recommended that all buildings be fitted with smoke alarms (it is mandatory for new buildings).

TECHNICAL SPECIFICATION
Power Adaptor Input: ………………………………………………………………………………………………… 230V
Power Output …………………………………………………………………………………………………. DC12V 1.5A
Puck Dims ………………………………………………………………………………………………………60x60x8mm
No of LED’s …………………………………………………………………………………………………………………..18

SERVICE WARRANTY
Electrovision Ltd. guarantees the product free from defects in materials and workmanship for a period of twelve months. Should this product be operated under conditions other than those recommended, or any attempts are made to service or modify the product, then the warranty will be rendered void. The product you buy may sometimes differ lightly from illustrations. This warranty is in addition to, and does not affect, your statutory rights. Our guarantee is administered by our retailers. If your product arrives damaged, you must contact the retailer from whom you bought it. The retailer’s contact details will be on the invoice that arrived with the product, or on the e-mail, you received hen you placed the order. Do not contact Electrovision,  only your retailer can arrange a replacement. If the product needs to be repaired or replaced, you must contact the etailer from whom you bought it. If you have just received your product and require technical help in using it, please call our Help Desk on (0845) 459 4816

Electrovision Ltd
Lots Lane
Sutton, St. Helens
Merseyside
WA9 3EX
www.electrovision.co.uk

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

EAGLE User Manuals

Related Manuals