imperii Alarm System GSM Soko User Manual

imperii Alarm System GSM Soko User Manual

For a better understanding of this product, please Read this user manual thoroughly before using it.

Features：

• Smart Phone APP
• 99 Zones,each zone can be renamed
• 10 zones are available for Voice Recording
• High-definition voice
• The Standard ADMECO Contact ID Protocol
• 99 wireless Zones,2 wired zones
• Upto 6 phone numbers to Dial out & 3 SMS Mobile numbers to send SMS on alarm.
• Intercom
• Upto 3 groups of Timely Arm/Disarm.
• Easy to code with Sensors/Detectors
• Remotely Arm/ Disarm /monitor / Intercom
• programming for zones.
• Voice prompt from Siren while arming/disarming by keyfob.
• Internal Re-Chargeable Battery for the back-up of power failure.

Technical Parameter

Default value

Defense Zone

|

Out Arm

|

Home Arm

|

Type Alarm

|

Information

|

Siren

---|---|---|---|---|---
Zone 1| Effective| | Real Time| Door Lock| On
Zone 2| Effective| | Real Time| Hall| On
Zone 3| Effective| | Real Time| Window| On
Zone 4| Effective| | Real Time| Balcony| On
Zone 5| Effective| | Real Time| Fire| On
Zone 6| Effective| | Real Time| Gas| On
Zone 7-97| Effective| | Real Time| SOS| On
Zone 98 (Wired)| Effective| | Real Time| SOS| On
Zone 99 (Wired)| Effective| | Real Time| SOS| On
| | | | |

Program Password:8888

Operationpass word:1234

Alarming Duration:180 Seconds

Diagram 1

1. Digital Display ：Standby Time(Minute for 5 Seconds; Hour for 1 second)

2. Set Button：To Set,Voice-Recording and Add Sensors etc.

3. SOS Button ：press to raise an emergency alarm. with more functions in setup state.

4. Alarm Light：flashing while alarming.

5. Arm Light：light on for Arming; flashes for Home Arm ;off for Disarm

6. GSM Indicator：fast blinks means No Sim card or Poor signal; blinks slowly means normal Signal.

7. SIM slot：SIM

8. Adapter Interface：For Power Adapter

9. Data Interface：For upgrading Software.
   a. Power on/off：for Internal Battery
   b. Interfaces：

   • SP+/SP- ： Outputs for Wired Siren
   • Z1/ Z2 ： 2 inputs for Wired Sensors
   • GND： Ground Wire

Diagram 2

Diagram 3

SP: Wired Siren, ,SP+ for Anode

1. Wired Sensor #1: Zone 98
2. Wired Sensor#2: Zone 99

Cautions：

1. No more than 5V for the Voltage of the Wire.
2. To avoid of the damage of the Host ,Please Power off before Connecting the Wire with the Host.
3. The Host will recognize the Wired Zones automatically as soon as the wired sensors connect with the Host. and you can set on the Host whether the siren goes off or not when the wired sensors’ triggered.

Daily Operation

1. Remote Controller

ARM:
Press (Arm ) to arm the alarm panel and the LED indicator lights on (siren hoots once), the system enters Arm state.
If there comes an intruder, the siren will hoot to deter the intruder.(The siren turns off after ringing for 5 minutes as default setting.) At the same time, the system dials the pre-stored phone numbers automatically.

DISARM:
Press (Disarm ) to disarm the alarm panel and the LED indicator blacks out (siren hoots twice), the system is disarmed. When intruders are detected, siren will keep hoo ting. Press (Disarm ) to stop siren hooting.

HOME ARM:
Press (Arm ) button on the remote control, the system state LED is on. All the sensors in other zones are armed except the motion detector in Home Mode Zone which is disarmed so that user can move freely at home.

SOS:
No matter what state the control panel is in, once SOS button on the remote control is pressed, the system immediately goes into emergent alarming state.

2. How to Control the Alarm System Via APP

1. Click the Menu you want, Options will display on screen, press【Down】
   

2. The Mobile will send SMS To the Host ,When it arrives to the Host
   

3. The Host will send the SMS to the App for the System’s Status
   

Notice：

• There will be a SMS fees while Controlling the system via APP
• To Control the system remotely by Calling, just Click 【Intercom】,The APP will call the Host , and then input the password to verify. And now you can ,
  • press 1 to Arm System
  • press 2 to Disarm System
  • press 3 to Monitor
  • press 4 to Intercom

3：Control the System by Sending SMS

ARM: Operation Password+1 【12341】
DISARM: Operation Password+2 【12342】
HOME ARM: Operation Password+3 【12343】

4：Answer to the call from S ystem

The Host will call the preset numbers(Mobile) in order when the defense zone’s triggered. When you answer to the call, you will hear the Alarming record and then you can do something as belows:
Press [1] to Stop the alarming , the system will stop calling and arm again.
Press [2] to Stop the alarming, the system will stop calling and Disarm.
Press[3] to Stop the alarming, the system will stop calling, and you can hear
what’s going on right now in your home for 30 seconds, and to press [3] again to keep monitoring .
Press[4] to stop the alarming, the system will stop calling, and you can talk with Anyone at home for 30 seconds and to press [4] again to keep intercoming
Press [9] to make the Siren on,,{you can press [2] to make Siren off}
And when you answer to the alarming Call from System, you will hear the voice prompt from the system, if you hang up without any instructions, the system will call the next number in order until someone answers to the call and react to the system with further instruction. The System will call all preset numbers in order for 3 times.

5： How to control the System via the Phone anywhere & anytime.

Call the system ,and you will hear a “beep” when the system answer the call, then input the password when you here the prompt.(the preset password is 1234).and then input the instruction(s) when you here the voice prompt from the System.
Press (1) on the phone to arm the system, you will hear “System’s Armed” when the set is
completely.
Press(2) to Disarm the System,you will hear “System’s Disarmed” when the set is
completely.
Press(3) to listen what’s going on right now in the house for 30 seconds ,and you can press
(3) again if you would like to keep listening.
Press(4). To intercom with the Host for 30 seconds and you can press (4) again if you
would like to keep intercoming
Press [9] to make the Siren on,,{you can press [2] to make Siren off}

Factory Reset

Firstly ,power off the system also to make sure the switch for Backup battery is off ,and then press the [SOS] button and Hold, meanwhile plug into the DC adapter, you will See the “EE” on the Host after 3 seconds.also there is long “beep” from the Host, and all Led Lights off. Then release the [SOS] button.

How to Add the Remote Controllers

In set-up state, press [set] button lightly, there will be a “beep” from the Host and [-1] displays on the Host. And press any button on the remote controller you would like to code with the Host after hearing the prompt of [Remote coding],
There is a “beep” from the Host the it receives the Signal from the remote controller,which means the coding is successful & completely .and you can add the maximum of 8 remote controllers ,just follow the above steps.

How to Delete the Remote Controller

In Set-up State, Press[Set] button lightly, there will be a “beep” from the host and [-1]displays on the Host. and a voice prompt of [remote coding] from the Host ,and then Press [SOS] Button to Delete all Remote Controllers.

How to Add the Sensors / Detectors

In set up state, press[Set] button lightly,the re will be a “beep” from the Host and [-1] displays on the Host , a voice prompt of [1 Remote coding],and then press [Set] button again, a voice prompt of [Detector coding],and then trigger the Detector ,there will be a  “beep” from the Host when it receives the signal from the Dector.,which means the coding with detector is successful & completely, and you will hear a voice prompt from the Host [2 Detector Coding],jut follow the above steps,you can add a maximum of 99 detectors How to Delete the Detectors. In setup state, Press [Set] button lightly, there is a beep from the Host,and [-1] displays on the Host, you will hear the voice prompt of “Remote coding”, press [set] button again to into the state for [1 Detector Coding],and the press [SOS] button to delete Detector#1, Press[Set] button again,[-2] displays on the Host,and voice prompt of [2 detector coding]. Then press [SOS] button to delete Detector #2.just follow the above steps to delete the other Detectors

While coding with Remote Controller or Detectors. af any digital display on the host with flashing also there is a voice of  “D1D1D1”, which means the code of the Remote or Detector is duplicated with the Remote or Detector already coded, just press (S0S) button to delete the Coded Remote or Detector and follow the instruction to add the new Remotw / Detector again.

System Setting

You can also make all the following settings via APP,which is really simple even you don’t need the user manual

Rename the Zones (just can make the setting via SMS or APP)

Just rename the every zone,which makes you can know which zone is triggered easily while receiving the alarming SMS. You can rename all of 99 zones individually
For Example: You would like to name the “1 Zone” as “Front Door Alarm” You just need to send the SMS as bellows to the Host: [programming password 8888]+[9]+[number of the Zone]+[#]+[name of the zone in text,20 at mostl+[#],just like:8888901#front door alarm# And you can make the same setting via APP under the menu of “Change Zone Name”

Make voice recording for the zone name

To make a voice recording for the zone name/address, which make you can know easily which zone’s triggered when you answer to the alarming call from the Host, and you can make the record for Zone 1 to Zone 9 individually. Just follow the steps as belows to make the voice recordings, In setup state,press and hold the [Set] Button until there is a“beep” from the Host, and “L1” displays on the host, then Press and Hold the [Set] button again until you see the
“H0” on the Host.which means you can start the voice recording, the Host will play the voice record automatically when the recording is complete. if you’re not satisfied with the effect of recording,press and hold the [set] button to make a recording again.and if you’re satisfied with it,just press[set] shortly to record for the other Detectors. When the [LA] Displays one the Host,Press the [Set] button shortly to exit the Voice Recording. and you can make the recording for the other zones by the same way. And you can make the same settings via APP under the menu of “Change Zone Voice”

How to Edit the Address of the Host(just can make the setting via SMS or

APP)

To edit the address of the Host,which make the people receives the alarming SMS know easily where your house it is and handle the emergency quickly.
For Example, you would like to edit the address as “No..101 of Bao’an avenue,ShenZhen”
Just send the SMS as bellows to the Host:

[programming password 8888]+[9]+[00]+[#]+[Address,20 at mostl+[#],just like:8888900#No.101 of Bao’an avenue,ShenZhen # And you can make the same settings via APP under the menu of “Voice recording (Address)”

Make a voice recording for the Address of the Host

To make a voice recording for the address ,which makes people who answers to the alarming call from you Host know easily where your house it is, and handle the emergency situation quickly. Just follow the steps as belows to make the voice recordings, In the state of disarm,press and hold the button [Set],there is a beep from the host,and [L1] displays on the Host,then press the button [set] shortly again and again,until there is [LA] on the Host,then Press and Hold the [Set] until you see the [H0] on the host,and now you can start the voice recordingly for the address. The host will play the record automatically when the recording is complete. And you can make the same settings via APP under the menu of “Voice recording Addres”

When the setting is complete you will see the alarming SMS is different comparing with the traditional Alarams, for example, the Alarming SMS from G10A will be “No.101 of Bao’an avenue  ShenZhen Front Door Alarm”. but for the traditional alarms it just shows like “ZOne 1 alaram”

When the setting is complete, you will “Hear” the difference for the alarming calling comparing with the traditional Alarams. for example, you will hear a voice recording from G10A while you answer to alarming call “No.101″ of Bao’an,ShenZhen,Front Door Alaram”

For the all settings bellows ,You can also make it via APP,which is really simple even you don’t need the user manual,and also you can do it by calling the system via the phone,just call the system and input the programming password and then input the instructions.

Change the Password

In Set up state,and then call the system via the phone and input [30] / [31] plus the new password [4-digitals] and end by the [#],there will be a long beep
from the host which means the setting is successful & Completed.
Change Operation Password :

Change program Password for example：

to change the program password into 0000。

Just call the system and input 310000#

Also you can make it vis SMS,just send the SMS of 8888310000# to the Host. Operation Password: when you call the system and input the Operation password, you can Arm/Disarm/Monitor the System –the original operation password is 1234.
Programming password: when you call the system and input the program
password,you can intercom/set the SMS receiving mobile number/other
settings
Notice: the Operation password and Program Password must be different
And you can make the same settings via APP under the menu of “Change Password”.

Phone settings

Phone numbers for receiving the alarm calling from the Host

When the system is triggered, the host will call the preset phone numbers, and you can hear the alarming information from the Host, including which zone is
triggered and the Address of the Host, you can add up to 6 groups of phone numbers
In setup state, call the system ,then input the code of [51]-[56] at the beginning and plus the phone(mobile) numbers, end by the [#].

Foe example add 6 groups of phone numbers

and delete the phone numbers

And if you would like to set the phone number of 0755-12345678 as the 2nd phone number,just make it as the bellow:

Also you can send the SMS to make the same setting, for example, You can send the SMS of 888852075512345678# to finish the setting And if you would like to delete the 3rd phone number just do it like

Or send the SMS of 888853# to the system [the number of the Sim Card of the Host]

And you can make the same settings via APP under the menu of “Phone Numbers” SMS Receiving numbers It Is for the mobile numbers receiving the alarming SMS when the system is triggered, a maximum of 3 groups

In the state of programming, input the code of [57]-[59] at the beginning, and plus the mobile numbers, end by the [#].

Adding SMS Receiving Numbers：57 – xxxxx –#

Delete the Numbers

For example,you would like to add 13811111111 as the 1st SMS receiving number,

And you would like to delete the 1st SMS receiving number

Also you can send the SMS of 888857# to delete the 1 st SMS receiving number

And you can make the same settings via APP under the menu of “ “SMS Numbers”

How to set the CID protocol

1： Contact Number

You can get it from your CID Service provider, it’s for uploading the alarming information to your Service Provider
How to set it :50 【Contact number】#
For example:set 0755-12345678 as the Contact number
50 【075512345678】#

To delete the Contact Number：50 #

And you can make the same settings via APP under the menu of “Ademco Contact”

2：User ID

It’s provided by your CID monitoring center,and it’s for recognizing the information from the Alarm systems, it’s a 4-digitals numbers

How to set it：78 【4 Digit ID】#

For example : to set [1234] as the User ID

78 【1234】#

And you can make the same settings via APP under the menu of “Ademco Contact”

3 ： Enable/Disable to upload the information to your monitoring center while

arming/disarming

To enable/disable to upload the status of the system to Monitoring center How to set it:74 【1/0】#

For example: to enable the function: 74 【1】#

And you can make the same settings via APP under the menu of “Ademco Contact”

4：Enable/Disable to upload the information to your Monitoring center while the system is triggered.
How to set it：73 【1/0】# For example : Enable the function 73 【1】#

And you can make the same settings via APP under the menu of “Ademco Contact”

Programming the zones

In the state of programming ,input address code of [60],and then zones number of [01-99],and [1-4] for the Mode of the zone,and then [1-8] for the Location of the Zone,and[0/1] for the siren goes off or not when the zone’s triggered,and press [#] to confirm。

How to make it ：【60】【A】【B】【C】【D】【#】

“A”For the Zone Number[1-99] “B”for Mode of the Zone,including [1] -Real-Time [2]Delay;[3]-24 Hours [4].-Bypass “C”for the location of the zone [1]-SOS[2]-Fire[3]-Gas[4][5]-Door[6]-Hall [7]-Window [8]-Balcony [9]-Boundary “D”for the siren will go off or not while the zone is triggered [0].the siren does NOT go off while the zone is triggered [1]the siren will goes off while the zone is triggered
For example,: to set zone 1 as the 24-Hours,Fire,and siren on when alarm

【60】【01】【3】【2】【1】【#】

also you can send SMS of 88886001321# to make the same setting. And you can make the same settings via APP under the menu of “Change Zone Attribute”

HOME ARM

In the status of Programming, input the address code of [61] ,and then the zone number of [1-99],plus[0/1] and press [#] to confirm,
How to make it ?：【61】【A】【B】【#】
“A”For the Zone Number[1-99]。
“B”under the status of [Home Arm/Stay Arm],，
【0】ineffective,which means the system does not alarm when the zone’s triggered【1】Effective,which means the system alarm when the zone’s triggered。
For example : to sent zone 1 as home arm zone and the system will alarm while the zone 1 is triggered
【61】【01】【1】【#】
also you can send SMS of 888861011# to make the same setting. And you can make the same settings via APP under the menu of “Change Zone
Attribute”.

Arm Delay Time

In the status of programming, input the address code of [44],and then the DelayTime [AAA] ,then press the [#]to confirm。
【44】【AAA】【#】
“AAA”means the Delay Time [001-180 seconds]。
For example : to set Arm delay time of 46 seconds
【44】【046】【#】
also you can send SMS of 888844046# to make the same setting.
And you can make the same settings via APP under the menu of “Set Arm Delay Time”.

Alarm Delay Time

In the status of programming, input the address code of [45],and then the DelayTime [AAA] ,then press the [#]to confirm。
【45】【AAA】【#】
“AAA”means the Delay Time [001-180 seconds] For example : to set Arm delay time of 80 seconds

【45】【080】【#】
also you can send SMS of 888845080# to make the same setting.
And you can make the same settings via APP under the menu of “Set Alarm Delay Time”。

Alarming Siren Duration

In the status of programming, input the address code of [46],and then the DelayTime [AAA] ,then press the [#]to confirm。
【46】【AAA】【#】
“AAA”means the Alarming Duration [001-180 seconds] For example : to set Alarming Duration of 60 seconds
【46】【060】【#】
also you can send SMS of 888846060# to make the same setting.
And you can make the same settings via APP under the menu of “Alarming Siren Duration”。

Remote Arm Delay

In the status of programming, input the address code of [47],and plus [1/0] to enable the function or Disable the function.th en press [#] to confirm,there will be beep from the host when the set is completed. The original setting is 【0Disable】
【47】【0/1】【#】
If you enable the Remote Arm Delay, when you press the arm/home arm button on the remote controller ,the system will not be armed until the Delay time is up And you can make the same settings via APP under the menu of “Other Functions”

Siren prompt for Remote Arm/Disarm

In the status of programming, input the address code of [75],plus [0/1] and then [#] to confirm
【1】means there will a voice prompt from siren when arm/disarm 【0】means there will no voice prompt from siren when arm/disarm The original setting is 【 0】,which means no voice prompt from siren when arm/disarm 【75】【A】【#】
“A” means there will a voice prompt or NOT from siren when arm/disarm 【0】 No voice prompt from siren when arm/disarm， 【1】 T means there will a voice prompt from siren when arm/disarm 1】。 also you can send SMS of 8888751# to make the same setting. And you can make the same settings via APP under the menu of “Other Functions”。

Siren on or off when press Remote SOS Button

In the status of programming, input the address code of [76],plus [0/1] and then [#] to confirm, there will be beep from the host when the set is completed. The original setting is 【0/off】 【76】【0/1】【#】
After enable the function, the siren will go off when you press the SOS button on remote And you can make the same settings via APP under the menu of “Other Functions”

SMS Notification for Arm/Disarm

In the status of programming, input the address code of [77],plus [0/1] and then [#] to confirm, there will be beep from the host when the set is completed. The original setting is 【0/off】 【77】【0/1】【#】
After enabling the function, the Host will send a SMS to the preset SMS receiving mobile numbers when the system is armed/disarmed And you can make the same settings via APP under the menu of “Other Functions”

Key Beep Setting

In the status of programming, input the address code of [79],plus [0/1] and then [#] to confirm, there will be beep from the host when the set is completed. The original setting is 【1/Artifical】

How to set :【79】【0/1】【#】

[0] : means Beep [1]: means Artificial

And you can make the same settings via APP under the menu of “Other Functions” SMS alert for Power failure In the status of programming, input the address code of [80],plus [0/1] and then [#] to confirm, there will be beep from the host when the set is completed. The original setting is 【1/on】

How to set【80】【0/1】【#】

[0] : disable the function [1] enable the function

When enable the function,the system will send the SMS about the status of the power to the preset SMS receiving mobile numbers And you can make the same settings via APP under the menu of “Other Functions System Date & Time In the status of programming, input the address code of [32],and the next of Year[AAAA],Month[BB],Date[CC],Hour[DD],Minutes[EE],Seconds[FF] and then [#] to confirm. there will be beep from the host when the set is completed.
How to set：【32】【AAAA】【BB】【CC】【DD】【EE】【FF】

【#】

AAAA：The year

BB：The Month。

CC：The Date。

DD：The Hour [24 hours model]。

EE：The Minutes。

FF：The Seconds。

For example： To set the system date as the 03:35:26 AM of June 16 ,2014

【32】【2014】【06】【16】【【03】【35】【26】【#】

also you can send SMS of 88883220140616033526# to the system to make the same setting. And you can make the same settings via APP under the menu of “System Date/Time Scheduling Timely Arm/Disarm

1 Scheduling Timely Arm

In the status of programming, input the address code of [33-35],and [AA] for hour ,[BB] for the minutes , then then [#] to confirm, there will be beep from the host when the set is completed.

How to make it：【XX】【AA】【BB】【#】

[XX]：means the address cod of [33][34][35], up to 3 groups of  Scheduling Timely arm [AA]：means the hours of the Timing arm [BB] means the Minute of the Timing arm。

For example：you would like to set the system arm automatically at 10:45 PM every day；

Just make it as ：【33】【22】【45】【#】

also you can send SMS of 8888332245# to the system to make the same setting. And you can make the same settings via APP under the menu of “Set Timely Arm”

2 Scheduling Timely Disarm

In the status of programming, input the address code of [36-38],and [AA] for hour ,[BB] for the minutes , then then [#] to confirm, there will be beep from the host when the setting is completed.

How to make it：【XX】【AA】【BB】【#】

[XX]：means the address cod of [36][37][38], up to 3 groups of Scheduling Timely disarm [AA]：means the hours of the Timing disarm [BB] means the Minute of the Timing disarm。

For example：you would like to set the system disarm automatically at 07:65 AM every day；J ust make it as ：【36】 【07】 【55】 【#】a lso you can send SMS of 8888360755# to the system to make the same setting.

And you can make the same settings via APP under the menu of “Set Timely DisArm”

3 Enable the function of Scheduling Arm/Disarm

In the status of programming, input the address code of [39],plus [0/1] and then [#] to confirm, there will be beep from the host when the set is completed. The original setting is 【1/on】

Just make it as：【39】【0/1】【#】

[0] means disable the function of scheduling arm/disarm [1]means enable the function of scheduling arm/disarm

For example :to enable the function of Scheduling arm/disarm

Just make it as：【39】【1】【#】

also you can send SMS of 8888391# to the system to make the same setting.

And you can make the same settings via APP under the menu of “Set Timely Arm” and Set Timely Disarm”

Adding wireless Siren (Optional) The wireless siren can be coded with G10A ,which make that you can mount the wireless away from the Host, The Wireless siren can not work until coding with the host

How to code:

press shortly the learning button on the Wireless siren to make the siren into the state of coding,then press [SOS] button on the Host to send the signal to wireless siren for coding. after coding with the host, the wireless siren goes off when the system is triggered, and the siren will stop alarming when disarm the system (there maybe a delay as it is connecting with the host wireless ) Enable the wireless control for wireless siren: Smart GSM Home Alarm 3 Activar la función de programación de armado / desarmado Adición de sirena inalámbrica (opcional) In the status of programming, input the address code[41] on the Host, plus [1/0]and then press [#] to confirm, there will be beep from the host when the setting is completed. The original setting is 【1/on】

Just make it as：【41】【0/1】【#】

[0] means disable the function of connecting with wireless siren [1] means enable the function of connecting with wireless siren

The Host can not control the wireless siren until enable the function

Wireless Code encryption: there may be disturb signal from the other devices, so it will be better to encrypt the wireless code How to encrypt the code: in setup state,input 43 （4-difital numbers） #

For example: 439876#

Also you can send the SMS to the host for encryption ：888843XXXX# nd you can make the same settings via APP under the menu of “Other Functions”.

9 Comm on malfunction

Fail to dial out via the Host|

• In the Disarm Status?
• Wrong Setting for the phone numbers
• In the status of Alarm delay
• SIM card is expired or past due

---|---
Siren Do Not go off while alarming|

• Power failure？

No Working Signal|

• Make sure SIM Card is GSM
• NO PINS for the SIM Card
• Low Battery
• Poor GSM Signal

Can not control remotely|

• Poor GSM Signal
• Change the SIM Card
• Test by another Mobile

Working distance of the accessories is more closer than before|

• Low battery

Technical Service:

Visit: http://imperiielectronics.com/index.php?controller=contact

imperii Alarm System GSM Soko User Manual – Download [optimized]
imperii Alarm System GSM Soko User Manual – Download
imperii Alarm System GSM Soko User Manual – OCR PDF

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>