Flipo UF-WIRELESS-DB Wireless Doorbell Instruction Manual
- June 6, 2024
- Flipo
Table of Contents
UF-WIRELESS-DB Wireless Doorbell
Instruction Manual
Wireless Doorbell
With Motion Sensing LED Security Light
Thanks for purchasing another Flipo® product intended to make life a little easier. FLIPO® offers a wide variety of unique products of the highest quality. To ensure the maximum performance of your product, please read and save these instructions.
Part
Doorbell Receiver
Doorbell Button With LED Light
Screws
Dry Wall Anchors
Set of Hook & Loop Adhesives| Quantity
1
1
2
2
2
---|---
IMPORTANT Your Receiver and Doorbell have pre-installed batteries. Remove the battery insulator strips from both the doorbell receiver and doorbell button battery compartment before first use.
BATTERY INSTALLATION
RECEIVER Remove the battery cover located on the rear of the Receiver
(Figure B). Install 3 AAA batteries according to the polarity indicated in
each battery slot. Replace the battery cover. For the best result, use
alkaline batteries.
DOORBELL The battery compartment is located on the rear of the Doorbell
(Figure C). Use a Philips head screwdriver to remove the two screws holding
the cover in place. Remove the cover and install 3 AAA batteries according to
the polarity indicated in each battery slot. Replace the cover, reinstall the
screws and tighten. For the best result, use alkaline batteries.
PRODUCT INSTALLATION
Screws, drywall anchors, and hook and loop connectors are included with your
product. You can choose to use any of the attachments, but if possible, use of
a screw is preferable. The Receiver and Doorbell can connect wirelessly up to
100′, but distances may vary based on the number and composition of walls
between the Receiver and Doorbell.
PAIRING
Your Receiver and Doorbell are not paired when first removed from packaging.
To pair, press and hold the Pairing Button located on the right side of the
Receiver for 3 seconds (Figure B). When you press the button to pair, the
doorbell tone will ring. After pairing, push the button on the Doorbell to
ensure successful pairing. If the Receiver does not ring, repeat this step
again.
RECEIVER & DOORBELL SET-UP
Choose the locations of both your Receiver and Doorbell. Before installing,
test the units by placing in their approximate locations and ringing the
Doorbell. If the receiver does not ring when you do so you may need to move
them nearer to each other. Your Doorbell button is weather resistant but
should NOT be placed in a location that may result in excessive exposure to
water. Once you have established locations the Doorbell and Receiver function
properly, mount them to the locations. It is best to mount each on a flat
surface such as a wall or door frame. If you use screws, install the screws
included in the proper locations leaving approximately ¼” of the screw and
head protruding from the wall. Slide the bayonet hanger located on the rear of
the Receiver and Doorbell over the protruding screw head (Figure B). If the
surface of the wall you will be mounting on is drywall using the included
drywall anchors to install your screw. If you will be using the hook and loop
closure to mount your Doorbell or Receiver, clean the surfaces of where you
will be applying each tab. Remove the paper covering the adhesive located on
the reverse sides of the hook and loop. Mount one to the flat surface and its
mate to the device. The piece that is mounted to the unit should be stuck to
the battery cover. Once hook & loop closures are in place, firmly press the
device to the flat surface to mount.
FUNCTIONS
Doorbell Button – PIR Activated Light
Each Doorbell Button includes a PIR Sensor and COB LED light. When
activated by motion the LED will illuminate the Doorbell’s push button. PIR
sensors ONLY function in darkened environments – the light will not turn on
needlessly during daylight hours. To activate, simply slide the switch located
on the left of the Doorbell up to the ON position (Figure E). When activated
the light will illuminate for approximately 20 seconds or until the movement
ends. Doorbell Receiver Volume The Receiver has three volume setting High,
Medium, and Low. To change the volume setting, simply push the VOLUME button
located on the top left side of the Receiver (Figure E). Each time you press
the button the volume will change in the cycle from low to medium to high.
Chime Tone Selection – Your Receiver has 6 chime tones Doorbell, Westminster
Quarters, Short Doorbell, Happy Birthday, Jingle Bells & The Nutcracker March.
To change the tone, simply press the CHIME TONE SELECTION button located on
the bottom left side of the Receiver (Figure A). Each time you press the
button the tone will change. Battery Life should the volume diminish from
the Receiver, the PIR Light begin to dim, or your devices not function in any
way batteries likely need to be replaced. For best result, replace with
alkaline batteries.
CAUTION
-
Your Doorbell button is weather-resistant but should NOT be placed in a location that may result in excessive exposure to water.
-
PIR sensors ONLY function in darkened environments – it will NOT function properly if ambient light such as a porch or street lights are nearby.
-
NEVER disassemble or otherwise alter or change the product.
-
Failure to insert batteries in the correct polarity, as indicated in the battery compartment, may shorten the life of the batteries, cause batteries to leak or damage the
product. -
Do not mix old and new batteries.
-
For best results, use alkaline batteries.
-
Do not mix Alkaline, Standard (Carbon-Zinc) Rechargeable (Nickel Cadmium), or (Nickel Metal Hydride) batteries.
-
Batteries should be recycled or disposed of as per the manufacturer’s recommendations.
FCC COMPLIANCE STATEMENT
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: 1. This device may not cause harmful
interference. 2. This device must accept any interference received, including
interference that may cause undesired operation.
ATTENTION: Modifications made to the device could void the guarantee of
the product
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of FCC rules. These limits
are designed to provide reasonable protection against interference in a
residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment o° and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/ TV technician for help.
30 DAYS LIMITED WARRANTY: FLIPO GROUP
warrants to the original purchaser, when used in North America only, that this
product shall be free of defects in material and workmanship. This warranty
applies within 30 days of the original purchase with normal home use. This
warranty does not apply for commercial use of this product. Use outside of
North America is not covered by this warranty. During the warranty period, we
will at our option, repair or replace this product without charge, which shall
be the consumer’s sole remedy. ALL RETURNS must be accompanied by a Return
Authorization Number, which is issued by the Customer Service Department of
Flipo Group. Please contact Customer Service BEFORE returning any item. Once
you have obtained a Return Authorization Number, the product must be returned
with a clear copy of the proof of purchase, showing place and date of
purchase, postage, and insurance prepaid to:
Flipo Group
613 First Street
La Salle, IL 61301
This warranty does not cover installation, adjustments in the home, nor damage
due to accidents, misuse, abuse, fire or other acts of God, incorrect line
voltage, damage to other equipment caused by improper installation,
unauthorized or improper modification. This warranty gives you specific legal
rights and you may also have other rights that vary from state to state.
Distributed by Flipo Group Limited La Salle, IL
Questions or Comments? Call:
815-223-9942
Email: info@flipo.com
Fax: 815-223-9266
MADE IN CHINA
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>