CARTONI HM6500 MASTER 65 User Manual

: June 8, 2024
: CARTONI

Table of Contents

CARTONI HM6500 MASTER 65
Introduction
Operating elements
Procedures
Specifications
Accessories & product line
Warranty
NEED HELP
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

CARTONI HM6500 MASTER 65

Introduction

In Broadcast and Studio configuration the new CARTONI MASTER 30 Fluid Head covers the needs of sophisticated video shooters from 3 kg (6.6 lbs) to 30 kg (66 lbs). With a low center of gravity (CG) configuration such as with Teleprompter, MASTER 30 holds 40 kg (88 lbs). An exceptional new fluid module in both Pan and Tilt modes ensures smooth movements, with perfect starts and stops, the drag system allows a wide variety from almost freewheeling in fast action movements to maximum resistance for perfect long focal shoots. The counterbalance performs perfect balance at any angle from 0 to +/- 90 degrees. All operating knobs and levers are conveniently located and easy to reach with a special care for ergonomics. The Head comes equipped with dual telescopic pan bars, illuminated spirit level and digital readouts for drag control and counterbalance settings

Before using the MASTER 30 Fluid Head, please make sure to read this user’s manual & maintenance;
Before installing the Fluid Head on the Tripod check the Tripod stability;
Check that the Camera payload (including lenses and accessories) is lower than the maximum capacity of the MASTER 30 Fluid Head;
Before installing the Camera make sure the MASTER 30 is in good conditions and bares no evident damages

Operating elements

```
1. Pan bar
```
Pan bar attachment lever
Pan bar attachment rosette
Tilt drag selector
Tie-down knob
Battery housing
Safety button slide lock lever
Tilt lock lever
Pan lock lever
Pan drag selector
Slide lock lever
Camera plate
Illuminated bubble level
Illuminated bubble level and display light button
Digital display
Horizontal lock button (Off)
Counterbalance selector
Horizontal lock button (On)

Procedures

Open the Tripod to the desired height and lock all safety knobs.
Place the MASTER 30 Fluid Head on the Tripod base and rotate until it matches the steel notch; tighten the Head firmly by screwing in the knob (5) underneath the flat base.
Check the illuminated bubble level (13) and modify the legs angle if needed.
In case of low visibility, press button (14) for illuminated bubble level and to activate the digital displays.
Lights will turn off automatically after approximately 30 seconds.
Lock the horizontal position with button (18), insert pan lock (9) and turn both tilt drag selector (4) and counterbalance selector (17) to position “0”.
To release the Camera plate (12) push the red safety button (7) and open the slide lock lever (11) completely till to position 2, then remove the Camera plate.
Attach the Camera plate under the Camera assembly and firmly secure it with both screws.
Try to place the Camera plate centered under the Camera system, keeping in mind the position of the center of gravity (CG).
Place the Camera on the top of the MASTER 30, leaning sidewards against the left side of the Head (slide lock side), then push the assembly into horizontal position until you feel the click of the slide lock lever (11), which will be in position 1 (at this point the Camera plate is clamped but still moving fore-and-aft).
Holding the pan bar (1) firmly, disengage horizontal lock with button (16) and find the correct center of gravity (CG) sliding the Camera assembly fore-and-aft.
Lock the slide lock lever (11) in position “0”. Set the counterbalance system by turning the counterbalance selector (17) to the appropriate tension The Camera has to stay still at any tilt angle.
If needed, fine tune the balance by adjusting the sliding plate.
Push button (14) to activate illuminated digital displays, unlock Pan lock (9) and select the desired Fluid drag intensity on both Pan and Tilt by turning Pan selector (10) and Tilt selector (4).

Specifications

Maintenance

When needed, with indoor use just clean the Head and Tripod with a soft cloth. Dirt accumulated during storage may be removed using a brush or Air spray. CARTONI products main mechanisms are sealed as they are also built for professional outdoor use. However, use under rough conditions they will require special care. Salt water is very corrosive and can cause extreme damages. In attempt to avoid further damage the Fluid Head should be washed off with fresh water at the earliest opportunity and perfectly dried before storage. Sand and dirt are abrasive and should be removed using a semi-stiff brush or Air spray. Disconnect the illuminated display & bubble level battery during long term storage; for battery replacement access the battery compartment (6).

Accessories & product line

For the complete Accessories list & Product line please visit CARTONI’s official website www.cartoni.com. Every product has an updated list of compatible items sorted by groups, with descriptions and technical data.

Warranty

All CARTONI Fluid Heads & Pedestals have a free of charge three (3) year warranty. Register your product at www.cartoni.com within 30 days from date of first purchase/invoice to receive further two (2) year warranty for the unsurpassed free five (5) year warranty. Tripods, spreaders, dollies and all accessories are guaranteed one (1) year from the date of first purchase/invoice. CARTONI warrant that the product supplied will – under proper use – be free from defects in workmanship and materials and agrees that it will, at its option, either repair or replace any defective part within duration of warranty from date of first purchase with no labour charge. This warranty does not apply to any CARTONI product that has been damaged in shipping or handling, abused, misused, operated contrary to instructions for use, neglected, normal wear or tear, modified or changed in design or construction or serviced by unauthorized parties. Repairs or misuse by any unauthorized parties will void this warranty. Warranty claims must be submitted – in writing – to the factory for verification or to an authorized distributor/dealer designated by CARTONI. It is the end user’s responsibility when ordering to ensure that the products ordered conform to his requirements. All freight of product to CARTONI must be prepaid. All implied warranties are limited to the time period set forth herein & subject to change without notice. No liability can be accepted for any variation.