CARTONI Focus 10 Red Lock System 100mm Ball User Manual

CARTONI Focus 10 Red Lock System 100mm Ball

SAFETY & SET-UP INTRODUCTION

The FOCUS 10 Fluid Head is the ideal support for the latest smaller, lighter high-performance Cameras weighing from 0 to 11 kg (0 to 24.3 lbs). Extremely compact and lightweight, the innovative FOCUS 10 features a continuously variable fluid damping system on both Pan and Tilt movements and an unrivaled patented variable counterbalance which brings its range of use to cover all existing ENG and lighter high-performance cam-eras. The FOCUS 10 head comes equipped with a quick-release sliding Cam-era plate, illuminated spirit level, and telescopic Pan bar. Its tilting range is +/- 90° and has a perfect response throughout the entire Tilt range. This Head interfaces with all 100 mm bowl base tripods and supports. The extreme ruggedness and versatility together with a superior quality/price ratio make the FOCUS 10 the best possible support for news Operators and Videographers. Before using your new FOCUS 10, please read this user manual. Before installing the Fluid Head on the Tripod check the Tripod stability. Verify that the Camera payload (including lens and all accessories) is below the maximum capacity of the Fluid Head. Before setting up the Camera, make sure that the Fluid Head is in perfect operative conditions with no damage.

Operating Elements

PROCEDURES

Place the FOCUS 10 on your Tripod by loosening the tie-down knob (11) under the Fluid Head and level using the spirit bubble (9). In low light conditions, press button (9) for light. Connect the Pan bar (12) to the Fluid Head tighten the lever (2) on the Pan bar attachment and select the desired operating angle. The telescopic Pan bar length can be adjusted via a lever (3). Lock both Pan and Tilt brakes (5 & 6), turn both Tilt drag selector (8), and counterbalance knob (10) to the minimum. Open completely the Camera plate lock lever (7) to release the Cam-era plate (1). Attach the Camera plate (1) under the Camera and tighten the clamping screw. Center the plate on the Camera, keeping the center of gravity position in mind. Place the camera sideways on top of the FOCUS 10, the wedge plate will lock into place: the Camera plate locking lever (7) will click into an intermediate position so that you can slide the Camera back & forth to the best position. Hold the camera in the horizontal position with the Pan bar (12) and re-lease the Tilt brake lever (6). To find the correct center of gravity position, slide the Camera plate (1) back & forth till you have achieved the desired balance. Lock the Camera plate lever (7) all the way to the “ON” position. Set the counterbalance system by turning the balance knob clockwise (10) to appropriate tension. The Camera has to stay at any tilt angle. Eventually fine-tune by adjusting the sliding plate. Unlock the Pan brake lever (5) and set the Fluid drag control by adjusting selectors (4 & 8). When the spirit bubble light fails it is time to replace the batteries (9). Pull out the battery tray. For easy mounting on a slider, the threaded shaft on the head bowl can be removed with a 10 mm Allen key and a 3/8 inch threaded hole will allow the connection.

SPECIFICATIONS

MAINTENANCE

For indoor use – when needed – just clean the FOCUS 10 and Tripod with a soft cloth. Dirt accumulated during storage may be removed using a brush or Air spray. CARTON:  product’s main mechanisms are sealed as they are also built for professional outdoor use. However, use under rough conditions will require special care. Saltwater is very corrosive and can cause extreme damage. In an attempt to avoid further damage the Fluid Head should be washed off with fresh water at the earliest opportunity and dried before storage. Sand and dirt are abrasive and should be removed using a semi-stiff brush or Air spray.  Disconnect spirit level battery during long-term storage. This warranty does not apply to any CARTONI product that has been damaged in shipping or handling, abused, misused, operated contrary to instructions for use, neglected, normal wear or tear, modified or changed in design or construction, or serviced by unauthorized parties. Repairs or misuse by any unauthorized parties will void this warranty. Warranty claims must be submitted – in writing – to the factory for verification or to an authorized distributor/dealer designated by CARTONI. It is the end user’s responsibility when ordering to ensure that the products ordered conform to his requirements. All freight of product to CARTONI must be prepaid. All implied warranties are limited to the time period set forth herein & subject to change without notice. No liability can be accepted for any variation.

WARRANTY

All CARTONI Fluid Heads & Pedestals have a free of charge three (3) year warranty. Register your product at www.cartoni.com within 30 days from the date of first purchase/invoice to receive a further two (2) year warranty for the unsurpassed free five (5) year warranty. Tripods, spreaders, dollies, and all accessories are guaranteed one (1) year from the date of first purchase/invoice. CARTONI warrant that the product supplied will – under proper use – be free from defects in workmanship and materials and agrees that it will, at its option, either repair or replace any defective part within the duration of warranty from the date of first purchase with no labor charge.

ACCESSORIES & PRODUCT LINE

For the complete Accessories list & Product line please visit CARTONI’s official website www.cartoni.com. Every product has an updated list of compatible items sorted by groups, with descriptions and technical data.

PROFESSIONAL CAMERA SUPPORT
CARTONI S.p.A
Via di Portonaccio, 33/B – 00159 Rome (Italy ) Phone +39 06 4382002
Fax +39 06 43588293
Email: cartoni@cartoni.com
www.cartoni.com

References

• Cartoni | Professional Camera Supports
• Make it sure, make it simple. - RINA.org

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>