NOMAD NM01838685 Base Station Compact User Guide
- June 6, 2024
- NOMAD
Table of Contents
NM01838685 Base Station Compact
User Guide
This product is based on electromagnetic induction technology, it meets the Qi WPC 1.2.4 wireless charging protocol issued by WPC (wireless charging Union). Power or charge devices that support the Qi 5W/10W/ 15W wireless charging protocol, Apple 7.5W, Samsumg10W, Google fast Charge.
Electric Parameter
a. Input Parameter | Comment |
---|---|
Input voltage range | 4.5V-17V |
Input voltage | 5V/9V/12V/15V DC |
Input power | 5V/2A;9V/2A;12V/2A;15V/2A |
10W 12V
Standby power| <500mW|
b. Output Parameter| | Comment
---|---|---
WPC Certification| Qi 1.2.4 15W EPP| Or the latest spec at the time of
certification
Output Power| OW-15W| BPP 5W @5-15V
APPLE 7.5W@9-15V EPP 10W@9-15V EPP15W@15V
Operating frequency| 110kHz-128kHz| 127.795kHz FOR APPLE Frequency Accuracy =
5Oppm
Power Modulation| Modulate voltage amplitude|
Led lights
Power-on self-test, enter the standby state after about 2 seconds (only 2 seconds of self-test for the first power on), during this period, and then go out; In standby mode, when the wireless charging device is sensed, the corresponding part of the pure blue LED lights up, when two receiving devices are placed, the other part corresponding pure blue LED lights up; When entering quick charging mode, the pure blue color LED will turn into pure red color; When recovering from quick charging mode to normal charging mode, the pure red color LED will turn back to the pure blue color; When the metal foreign object(FOD) is detected, the pure red LED flashes.
a) work indicting lamp Working
OV0rking | N. LED |
---|---|
Power-on | on 2s then off |
Standby | LED off |
Charging | LED on |
Charging full | LED on |
b) Alarm type
Alarm type | Led |
---|---|
Over-temperature/Low-temperature | Flashing LED |
FOD | Flashing LED |
Overvoltage | Flashing LED |
Under voltage | Flashing LED |
Other | Flashing LED |
c. Protection Requirement
No | Item | product qualification |
---|---|---|
a | Input Low-voltage protection | 4.3±0.2V |
b | Input Over-voltage protection | 17±0.5V |
c | c Input Over-current protection | ?2A |
d | Over-temperature protection | -10°C > °C < 60°C |
FOD (Foreign object detection)
The device has an FOD function. When a metal foreign object is detected,
enters the FOD mode, the pure red LED flashes, 1 time/sec; When the metal
foreign object is removed, the device exits FOD mode and enters standby mode.
Environment Requirements
a. Operation temperature and relative humidity.
- 10°C to +25°C;10%RH to 85%RE,
b. Storage temperature and relative humidity.
- 20°C to +80°C;5%RH to 95%Rflo
FCC WARNING
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
To maintain compliance with FCC’s RF exposure guidelines, This equipment should be installed and operated with a minimum distance of 20cm from the radiator of your body: Use only the supplied antenna.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>