DEERC D50 Drone for Adults Instruction Manual

DEERC D50 Drone for Adults

DISCLAIMER & WARNING

1. Please read this Disclaimer & Warning and Safety Guidelines carefully before using our product This product is not recommended for people under the age of 14. By using this product, you hereby agree to this disclaimer and signify that you have read it fully You agree that you are responsible for your own conduct and any damaged caused while using this product, and its consequences . You agree to use this product only for purposes that are proper and in accordance with local regulations, terms and all applicable polices and guidelines Deere may make available.
2. When using this product, please be sure to strictly abide by the specifica­tion requirements and safety guidelines stated in this document Any personal injury property damage, legal disputes and all other adverse events caused by the violation of the safety instructions or due to any other factor, WILL NOT be Deere’s responsibility.

SAFETY GUIDELINES

Check Before Use:

1. This product is a high precision drone that integrates various electronic stability and control mechanisms. Please be sure to setup this drone careful­ly and correctly to ensure safe, accident-free operation.
2. Please be sure that the batteries of the drone and transmitter are clean, undamaged and, fully charged.
3. Please be sure that all the propellers are undamaged and are installed in the correct orientation.
4. Please do a thorough check of the product before each use. Inspect the integrity of the parts, any signs of cracks and wear of the propeller, battery power and effectiveness of the indicator, etc. If a?er doing a complete check any issues are found, please refrain from using the product until the issue has been resolved.

Flight Environment

• Avoid flying over or near obstacles, crowds, high voltage power lines, trees, airport or bodies of water.
• DO NOT fly near strong electromagnetic sources such as power lines and base stations as it may affect the onboard compass.
• Don’t use this drone in adverse weather conditions such as rain, snow, fog, and wind.

Operation Requirements:

1. Please don’t use this product to follow any moving vehicles .
2. During the flight, only turn off the motor in case of an emergency,
3. As battery becomes low return the drone back to your starting point.
4. This product should not be used while drinking alcohol, if you are feeling fatigued, taking medicine, or feeling any physical discomfort.
5. Beware of the noise volume the drone produces. Keep your distance to avoid ear damage.
6. Stay away from the rotating propellers and motors.
7. Don’t fly in the No-Fly Zone.

Use of Battery:

1. Please ensure batteries are fitted in the correct orientation as shown in the instruction manual.
2. Avoid short circuits by fitting the batteries correctly, and do not crush or squeeze the batteries as this could carry the risk of an explosion.
3. Do not mix new and old batteries as this can lead to a poor performance of the product.
4. Dispose used batteries carefully, do not litter.
5. Please keep dead batteries away from heat and fire.
6. If the device is not going to be used for an extended period of time, remove batteries to prevent potential damage from battery leakage.
7. It is recommended to only use the USB charging cable that comes with the drone to charge the battery.
8. Don’t connect the battery directly to wall outlets or car cigarette -lighter sockets.
9. Don’t attempt to disassemble or modify the battery in any way
10. Don’t use the battery if it gives off an odor, generates heat, becomes discolored or deformed.or appears abnormal in any way If the battery is in use or being charged, remove it from the device or charger immediately and discontinue use.
11. Don’t pierce the battery casing with a nail or other sharp object, break it open with a hammer, or step on it!
12. Always charge the batteries in a fireproof container and away from combustible materials. Don’t charge on surfaces that can catch fire. This includes: wood, cloth, carpet, or in the application’s device.
13. Don’t immerse the battery in water or allow it to get wet
14. Don’t solder battery terminal directly
15. Keep battery out of reach of children or pets.
16. Don’t short-circuit the battery by connecting wires or other metal object to the positive(+) and negative(-) terminals.

Li-Po Battery Disposal & Recycling
Waste Lithium-polymer batteries must not be placed with household trash. Please contact local environmental or waste agency or the waste agency or the supplier of your model or your nearest Li-Po battery recycling center.

MAINTENANCE

1. Clean the product after each use with a clean, soft cloth.
2. Avoid prolonged exposure to direct sunlight and avoid buildup of heat on the drone.
3. This device is not waterproof and must not be submerged in water under any circumstance. Failure to maintain the device completely dry will result in the failure of the unit.
4. Check the charging plug and other accessories for signs of damage frequently If any part of the device is damaged, refrain from fiying until maintenance can be carried out.

PACKAGE CONTENTS

DRONE’S DETAILS

TRANSMITTER DETAILS

MODE 2
(Lelt hand throttle MODE 2 will be default setting.)

MODE 1
To enter MODE I, turn on the transmitter while holding the “Take Photo” button. (Please do not release the ‘Take Photo” button until the transmitter is powered on.)

CHARGING

Make sure the battery is fully charged before each flight

1. When the drone battery runs low. the indicator lights on the drone will blink quickly, and the transmitter will continuously emit a “Di” warning sound.
2. Remove the battery and connect the USB charging cable to the battery.
3. Plug the USB charging cable into a USB charging port on the computer. power bank or USB adapter (SV/0.5 to 2.0A ).
4. The red indicator light on the battery will turn on when it is charging. and will turn off when the battery is fully charged.
5. Charging time: about 90 minutes.
   • Due to transportation requirements. the battery have been discharged before leaving the factory (30% power remaining). Make sure the battery is fully charged before you use it for the first time.
   • Before charging. please check the contents of the ” Use of Battery” section of the “Safety Guidelines” carefully!

INSTALLATION

Propellers

The drone will not fly unless the correct propeller is installed on the correct motor sharr. See illustration above. An “A” or “B” is printed on the each propeller. Lock the propeller to the motor sharr with screw rotating each screw clockwise.

Drone Battery

• Installation: Push the battery correctly into the drone battery compartment. Make sure the battery is in place to ensure that the battery is jammed in the battery compartment. (Pie 1)
• Removal: Press the lock on the bottom of the battery and pull it back to remove the battery from the fuselage. (Pie 2)

Propeller Guard

Installation:

1. As shown above, push the propeller guard into the motor base. (Pie 3)
2. The protection guard can be fixed by pressing the clip on the propeller guard. (Pie 4)

Removal: The propeller guard can be removed by pushing up the clip on the propeller guard. (Pie 5)

Landing Gear

• Installation: Push the landing gear into the landing gear chuck on the fuselage. ( Pie 6)
• Removal: The landing gear can be removed by pulling back the landing gear while slightly pressing the buckle of the landing gear on the wing. (Pie 7)

Transmitter Battery

• As shown above, insert the battery into the battery compartment. Please pay attention to the positive and negative polarity of the battery to ensure the correct installation of the battery.
• When the transmitter battery runs low, the transmitter will constantly beep.

Phone Holder

1. As shown above, install the phone holder to the transmitter.
2. Open the phone holder and put the phone. Then you can use the FPV real-time transmission function.

OPERATION GUIDE

Download APP

• Scan the OR code, corresponding to either App Store™ or Google Play™ Store and download the Deere FPV app for free.
• Required Operating Systems: iOS 7.0 or later/ Android 4.4 or later

Connect to Wi-Fi
Connect your smart phone to the Wi-Fi network created by the drone. Check the drone’s status in the Deere FPV app.

1. Your smartphone will launch a search of the available Wi-Fi networks:

2. Select the Wi-Fi network: DEERC-**.

3. Wait for several seconds until your smartphone connect to the Wi-Fi network of the drone.
   This connection is generally represented by the Wi-Fi logo appearing on your smartphone’s screen.

4. Launch the Deere FPV application.

   • The connection between your smartphone and the drone will be established automatically.

All of the following operations on this manual takes MODE 2 for example.

Pairing

1. Push the power button to “ON” status to turn on the drone and the indicator lights on the drone begins to flash.
2. Place the drone on a fiat and level surface with the head forward and the tail towards the pilot.
3. Press the power switch button on the transmitter to turn it on and you will hear “Di'”, then the indicator light on the transmitter will flash.
4. Push the left joystick up then down to pair the drone with the transmitter. The indicator lights on the drone and the transmitter will turn solid if the drone is paired successfully.

Calibrating the Gyroscope

Push both joysticks down to the bottom left to calibrate the gym The indicator lights on the drone will blink quickly and turn solid, indicating calibration is completed.

Tips:
To ensure a stable flight, we suggest that the pilot calibrates the gyro every time after pairing the drone and after a crash.

One Key Start/ Landing

1. Short press the One Key Start; Landing button, the propellers will start spinning at low speed. Slowly push the throttle joystick up to take off.
2. When the drone is flying, short press the same button again, the drone will automatically land on the ground.

FUNCTION DETAILS

Emergency Stop
The Emergency Stop function can be only used in case of emergen­cy during the flight to avoid any of damage or injury.

Press the upper left and upper right button of the transmitter at the same time, the motors will stop immediately.

Speed Switch
This drone comes with 4 speed levels (Low/ Medium/ High/ Expert). Press the Speed Switch button on the back of transmitter to switch the speed. “Di” indicates Low speed, “Di Di” indicates Medium speed, “Di Di Di” indicates High speed and “Di Di Di Di” indicates Expert speed. (The Low Speed is default speed mode.)

Trimmer Function

F/B Sideward Fly Trim:
If the drone drifts forward, press the Backward Trimmer button to re-balance the drone. If the drone drifts backward, press the Forward Trimmer button to re–balance the drone.

L/R Sideward Fly Trim:
If the drone drifts left, press the Right Trimmer button to re–balance the drone. If the drone drifts to right, press the Left Trimmer button to re–balance the drone.

Take Photo/Video

• Take Photo: Short press the Photo button on the transmitter to take pictures. One beep can be heard from the transmitter, indicating the camera has successfully taken one photo.
• Record Video: Short press the Video button on the transmitter, two beeps from the transmitter will be heard. This tells you that the camera has started recording video. You can exit the recording by short pressing the same button again.

Do not take photos during the recording, which will interrupt the recording.

Camera Angle Adjustment

As shown in the figure above, you can long press the Photo button to make the lens up, and long press the Video button to make the lens down. (The camera has an 90″ tilt range.)

360° Flip

• When you get familiar with all the functions of the drone, you can try this amazing flip mode. When you fiy the drone at least IO feet, short press the  360 Flip button on the transmitter, then push the right joystick Forward/
• Backward or Left/ Right, and the drone will do a fiip towards the corresponding direction.
• If you are in MODE I, push the right joystick Left/Right or push the left joystick Forward/Backward, and the drone will do a flip towards the corresponding direction.

Headless Mode

1. After pairing/ calibration, or during the flight of the drone, long press the Headless Mode button on the transmitter. The transmitter will beep once to indicate that drone is in Headless Mode.
2. Press the Headless Mode button again, and you will hear a “Di Di”, which indicates the drone exits the Headless Mode.

Please make sure the pilot to stay in the same orientation as the drone head faces when the drone is pairing.

Under Headless Mode, the forward direction is the direction that the head of drone faces when the drone is pairing. In order to make sure the pilot can tell drone’s direction, we recommend that pilots to stay in the same orientation as the drone’s head faces when the drone pairing. When the pilot pushes the direction joystick forward, the drone will fiy forward. If the pilot pushes the direction joystick backward, the drone will fly towards him/her. If the pilot move the right stick left/right, the drone will move left/right relative to you.

SPECIFICATIONS

DRONE

• Model: DS0
• Weight: 178g/ 6.28oz
• Flight Time: 11 minutes (per battery)
• Operating Temperature Range: 32° to 104° F (0° to 40°C)
• Dimensions: 316316 108 mm

DRONE BATTERY

• Capacity: 1500mAh
• Voltage: 3./V
• Energy: 5.55 Wh
• Battery Туре: Li-Po Battery
• Charging Temperature Range: 41° to 104°F (5° to 40°C)
• Charging Time: 90 minutes (depends on charging power and remaining battery power)

TRANSMITTER

• Operating Frequency: 2.4 GHz
• Transmission Distance: 164 feet/ 50m (outdoors and unobstructed)
• Operating Temperature Range: 32° to 104°F (0° to 40°C)
• Battery Type: 1.5V AA Battery

CAMERA

• Camera frequency: 2.4 GHz
• Lens Angle: 120°
• Controllable Range: Pitch: -90° to 0°
• Video/Photo Resolution: 2048×1152P
• Image Return Distance: 164 feet/ 50m (outdoors and unobstructed)
• Transmission Frame Rate: 25 fos
• Photo Formats: JPEG
• Video Formats: AVI / MP4
• Operating Temperature Range: 32° to 104°F 10° to 40°C)

USB CHARGING CABLE

• Voltage: 5 V
• Rated Power: <10 W

CONTACT US

Please do not hesitate to contact us if you need further support.

• usa@deerc.com (USA)
• jp@deerc.com (PI)
• eu@deerc.com (EU)

For online support, please scan this code with Facebook Messenger.

GENERAL INFORMATION

FCC Statement

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

This device complies with part I 5 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particu­lar installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

WARNING:
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

RF Exposure
The equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This device should be installed and operated with minimum distance 20cm between the radiator & your body This part belongs to the drone.

RF warning for Portable device:
The device has been evaluated to meet general RF exposure requirment. The device can be used in portable exposure condition without restriction. This part belongs to the transmitter.

IC Notice:
This device complies with Canada Industry licence-exempt RSS standard(s). Operation is subject to the following two conditions

1. this device may not cause interference; and
2. this device must accept any interference. Including interference that may cause undesired operation of the device.

CAN NMB-3 (B)
RF Exposure

Radiation Exposure Statement:
This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operat­ed with minimum distance 20cm between the radiator & your body.

HOW TO RECYCLE THIS PRODUCT

• This symbol on the product or its documentation indicates that it must not be disposed of with household waste.
• Uncontrolled waste disposal may harm the environment or human health. Please separate your device from other types of waste to recycle it responsi­bly.
• This will help to foster the sustainable re -use of material resources.
• We invite you to contact your retailer or inquire at your local town hallto find out where and how the drone can be recycled.

BATTERY WARNING:

1. Failure to follow all the instructions may result in serious injury, irreparable damage to the battery and may cause a fire, smoke or explosion.
2. Always check the battery’s condition before charging or using it.
3. Replace the battery if it has been dropped, or in case of odor, overheat­ing, discolouration, deformation or leakage.
4. Never use anything other than the approval LiPo charger the battery. Always use a balancing charger for LiPo cells or a LiPo cell balancer. It is recommended that you do not to use any other charger than the one provided with the product.
5. The battery temperature must never exceed 60ºC (140ºF) otherwise the battery could be damaged or ignite.
6. Never charge battery on a flammable surface, near flammable products or inside a vehicle (perferably place the battery in a non-flammable and nonconductive container).
7. Never leave the battery unattended during the charging process. Never disassemble or modify the housing’s wiring, or puncture the cells. Always ensure that the charger output voltage corresponds to the voltage of the battery. Do not short circuit the batteries.
8. Never expose the Li Po battery to moisture or direct sunlight, or store it in a place where temperatures could exceed 60’C(car in the sun, for example).
9. Always keep it out of reach of children.
10. Improper battery use may result in a fire, explosion or other hazard.
11. Non-rechargeable batteries are not to be recharged. Rechargeable batteries are only to be charged under adult supervision.
12. Different types of batteries or new and used batteries are not to be mixed.
13. Batteries are to be inserted with the correct polarity.
14. The supply terminals are not to be short-circuited. Regular examination of transformer or battery charger for any damage to their cord, plug, enclosure and other parts and they must not be used until the damage has been repaired.
15. The packaging has to be kept since it contains important information.
16. The toy is only to be connected to Class II equipment bearing the symbol.
    • EU RF Power(EIRP) <IO dBm (2413MHz – 2461 MHz)

Caution

1. The max operating of the EUT is 45ºC. and shouldn’t be lower than -10ºC.
2. The device complies with RF specifications when the device used at 0mm form your body.
3. Declaration of Conformity.

We, Xiamen Huoshiquan Import & Export CO.,LTD
hereby, declare that the essential requirements compliance with the Directive 2014/53/EU, the RoHS Directive 20 I 1/65/EU and Safety Directive 2009/48/EC have been fully fulfilled on our product with indication below:

• Product Name: REMOTE CONTROL MODEL/RADIO CONTROLLED
• Mode/Mark: DS0/DEERC
• The Statement of compliance is available at the following address:
  http://www.holystone.com/Download/CE/D50_EU_DOC.pdf.

MANUFACTURER INFORMATION

Manufactured by

Xiamen Huoshiquan Import & Export CO.,LTD
Room 703,No. 813-2 Xiahe Road, Siming District, XIAMEN, China.
+ I 855-888-6699

Made in China.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>