kogan KASMARTBLIB SmartHome Smart Blind Driver User Guide
- June 6, 2024
- Kogan
Table of Contents
User Guide
kogan SmartHome™ Smart Blind Driver
KASMARTBLIB
INSTALLATION
Power on the device
Connect the power adaptor with a wall outlet, then connect the power cable to
the device.
Installing mounting bracket
Pull down on the blind adjustment chain, ensuring it is taut and without
slack. Hang the supplied installation card on the bottom of the chain, keeping
the chain held tight. According to the chain position, mark the two “L” or “R”
holes on your wall.
To identify Left or Right usage:
While standing and facing the blinds, if the chain/rope is on your left-hand
side, refer to “L”. If the chain/rope is on your right-hand side, refer to
“R”.
Installation model (permanent) For permanent installation, mark the two holes
for either “L” or “R” installation with the card. Replace the card with the
mounting bracket, and screw it into place. The mounting bracket can be
installed this way either by its side or flat.
Installation mode 2 (no holes, removable) For a removable installation, use
supplied 3M adhesive to fix to the wall. It is recommended to leave the
mounting bracket to set on the wall for at least 12 hours before applying the
full weight of the attached device.
Fitting blind adjustment chain to device
Open the device backing by pushing gently inwards to release.
Determine the suitable gear from the below diagram, and attach this to the
device.
Fix the blind adjustment chain to the gear, and close the device backing.
| |
---|---|---
2mm 4mm 6mm| 4.5x6mm 4.5x12mm metal chain| beaded chain 3.2mm
Please note that if the incorrect gear is selected, the chain will be noisy during operation.
Note: This device is suited only for blinds with a looped adjustment chain, and not suited for blinds with free-hanging cords or an adjustment wand/rod.
Attaching the device to the mounting bracket
Once the mounting bracket is installed, simply attach the device to the bracket via the two grooves on the rear of the device, and slide down until it locks into place. Ensure the chain is reasonably tight, with no slack.
To remove the device from the
mounting bracket, simply press the Release Button. Push up from beneath, slide
up along the groove, open up the backboard and remove the chain.
CONFIGURATION
Running direction
With the chain placed on the motor, check if the running direction matches
that of the blinds. If not, there are two methods for changing the running
direction.
A: Press and hold the “Up” button for six seconds, until the blue light
begins to flash. This reverses the blind running direction.
B: After connection with the app is complete, you can change the device’s
motor direction by selecting ‘Motor direction’ from the ‘More submenu. You
will then need to reset the device limit, as the difference in direction will
change the limit.
Set device limits
-
Push the Up Arrow (left button) until the shades open all the way.
-
Push and hold the Stop button until the red light flashes (about 5 seconds).
-
Reach the high limit position, push the Stop Button.
-
Once the red light flashes push the Down Arrow until the shades close.
-
Hit the Stop Button when they are completely closed. The device will wait a few seconds and then flash.
Now the blinds motor will automatically stop at the pre-set upper and lower limits. If the range changes, please reset the device.
Pairing with the remote
The device not only pairs with the mobile but also with the remote.
A holder for the remote
control is included, which can be secured to the wall if desired.
Factory Reset
To reset the device, push the Up Arrow (left button) & Down Arrow (right
button) for about 8 seconds until it flashes the lights.
CONNECT TO SMARTERHOMETM APP
Install App
Download the “Kogan SmarterHome” app from the Play Store (Android) or App
Store (i0S).
Register
If you do not have a Kogan SmarterHomeTM account, register or sign in with a
verification code sent by SMS.
To register:
- Tap to enter the registration page.
- The system automatically recognizes your country/area. You can also select your country code manually. Enter your email address and tap ‘Next’
- Alternatively, you can select ‘Register by the mobile number’ and enter the verification code sent to you by SMS.
- Create a profile on the next page to define your location and room.
Set device in pairing mode
When the device is first turned on, it may enter pairing mode (the Up arrow
will be flashing).
If not automatically in pairing mode when powered manually set the device in
pairing mode by holding (the left button) and Stop Button (middle button)
simultaneously until the ‘Up’ arrow begins flashing
Add device through the network
-
Once registered, tap “ + ” in the upper right corner of the app’s home page to add a new device through the network.
-
Select the product type from the list of options in the app (Electrical > Smart Blinds Driver).
-
Ensure that the device is in pairing mode, with the example of indicator, and tap “Confirm light is rapidly flashing”.
-
Upon successfully confirming pairing mode, enter your Wi-Fi details. It is important that your SmarterHome™ device and the app are connected to the same Wi-Fi network during setup.
-
The device will commence the pairing process and connect to the app. Ensure your Wi-Fi router, mobile phone, and the SmarterHome device are kept close until the connection is complete.
-
After successfully being added, you will have the option to rename the device and assign it to a location. It will now be listed on the app’s home page. Tap the device listing to enter its control page.
Notes.
- The device and the app have to use the same Wi-Fi network.
- The device is only compatible with 2.4Ghz networks.
USING SMARTERHOME™ APP
The connection is now complete, and you can tap on the ‘open’ or ‘closed’ blind icons to trigger the function directly via the app.
Schedule
Use the scheduling function to set the blinds to open or close at set times of the day. Times will have a variance factor of +/- 30 seconds.
GOOGLE HOME CONTROL
Note: You will need to have set up a Google Home account prior to linking your Kogan SmarterHomeTM device.
Adding “SmarterHome” to the Google Home app
-
From the home page of the Google Home app, select the “+” icon to access the ‘Add and manage’ page.
-
Select ‘Set up the device, then under the Works with Google banner, select ‘Have something already set up?’
-
Select the search bar and type ‘Smarter Home to locate the Kogan SmarterHomeTM service.
-
Tap ‘Authorise’ to grant Google permission to access the SmarterHomeTM app and your devices.
-
From here, you will be prompted to sign in to your SmarterHomeTM account using either your email or mobile phone number, depending on which method you used to register your account.
-
Once connected, the app will display any compatible devices linked to your SmarterHomeTM account. From here you can assign them to rooms and set up any routines.
-
Tap on any of the devices to view a list of available commands. Try saying “Hey Google, close the blinds,” or “Hey Google, open the blinds to 40%”
Note: Please note that Google Home can only control the base/core functions of any compatible SmarterHomeT” devices. To make full use of this product’s smart functionality, please use the Kogan SmarterHomeTM app.
AMAZON ALEXA CONTROL
Note:
You will need to have set up an Alexa account prior to linking your Kogan
SmarterHome” device.
Adding “SmarterHome” to the Alexa app
-
From the home page of the Alexa app, select the icon in the top-right and select Skills & Games from the sidebar.
-
Select the search bar and type ‘Smarter Home to locate the Kogan SmorterHome™ skilL
-
Tap ‘Enable to Use to add the Kogan SmarterHomeTM skill to Alexa.
-
From here, you will be prompted to sign in to your SmarterHomeTM account using either your email or mobile phone number, depending on which method you used to register your account.
-
Tap ‘Authorise’ to grant Alexa permission to access the SmarterHomeTM app and your devices.
-
Once connected, the app will perform a search and display the devices linked to your SmarterHomeTM account.
-
When your devices have successfully connected to the Alexa app, you will be able to control your Kogan SmarterHome devices via Alexa’s voice commands. Try saying “Alexa, close the blinds,” or “Alexa, open the blinds to 40%”
Note: Please note that Alexa can only control the base/core functions of any compatible SmarterHomeTM devices. To make full use of this product’s smart functionality, please use the Kogan SmarterHome app.
SPECIFICATIONS
Control method
Torque
Speed
Adapter voltage
Frequency
Voltage
Rated current
Maximum blinds size
Maximum weight
Distance| Mobile or remote
1.35N.m
55rpm
110V-240V
2.4GHz
12V
1.2A
2.5m x 3.5m
10kg
Within the range of Wi-Fi signal
---|---
Need more information?
We hope that this user guide has given you the assistance needed for a simple setup.
For the most up-to-date guide for your product, as well as any additional
assistance you may require,
head online to help.kogan.com
Documents / Resources
|
kogan KASMARTBLIB SmartHome Smart Blind
Driver
[pdf] User Guide
KASMARTBLIB, SmartHome Smart Blind Driver
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>