laia B&H 4K AI22 Camera User Manual

laia B&H 4K AI22 Camera User

SAFETY NOTES

The following important notes must be followed carefully to run the camera and respective accessories in total safety. The camera and relative accessories are called video systems in this section.

• Before installing the camera, please read this manual carefully. Please follow the installation instructions indicated in this manual during installation. Please keep this manual for future use.
• Please put the power cable, video cable, and control cable in a safe place.
• Do not operate the camera beyond the specified temperature and humidity. The working temperature range of the camera is between 0℃ ~ and +40℃. The ambient humidity range is 10%RH ~ 90%RH.
• During transporting, avoid violent shaking or force to the camera.
• To prevent electric shock, do not remove screws or the housing of the camera. There are no self-serviceable parts inside. Refer to qualified service personnel for servicing.
• Never aim the lens of the camera at the sun or other extremely bright objects. Otherwise, it may cause damage.
• When cleaning the camera, please use a soft cloth. If the camera is very dirty, wipe it off gently with a soft cloth moistened with a weak solution of water and a neutral kitchen detergent. Wring all liquid from the cloth before pinging the camera, then wipe off all remaining dirt with a soft, dry cloth. Use lens cleaning paper to clean the lens.

ABOUT THE PRODUCT

Characteristics & Functions

• High-quality CMOS image sensor, up to 3840x2160P30 video output;
• High quality 4K super wide-angle lens, no distortion;
• Manual image adjustment;
• Support auto framing function based on intelligent image algorithm;
• EPTZ function;
• Supporting YUY2, NV12 uncompressed video formats, MJPG, H.264, H.265 compressed video formats;
• Built-in MIC audio input;
• UVC/UAC communication protocol;
• Standard USB3.0 Type-C interface is adopted.

Accessories
When you open the box, check all accessories according to the packing list.
Camera X1 Remote Controller X1

USB Cable X1

Main Parts & Interfaces

CAMERA
Front View:

1. Camera Module
2. Camera Indicator Light
3. Microphone
4. IR Sensor

Side View:

Bottom View:

Mounting Hole
1/4” inch screw, used to fix the camera.

Remote control(standard)

2 Menu

| Open/close the OSD menu
3 Zoom|  zoom in,  zoom out

4 Direction

| In menu mode,set menu options;

In non-menu mode， or used for vertical

adjustment of the screen;

or      used for horizontal adjustment of the screen

5 HOME

| In menu mode, confirm to enter;

In non-menu mode, the screen returns to the

original position

---|---
6 Focus| Reserved
7 Autofocus| Reserved
8 Auto

Framing

| Press F1 to enable; Press F2 to stop

9 Number

| Set and call the preset point

Common function

When the camera is in a working state, the indicator light is blue, always on.

1. EPTZ
   The camera supports EPTZ control and 4x digital zoom. The EPTZ can be controlled via direction keys to adjust the image position. And the current image size can be adjusted via the zoom button.
   Note: when the image is under max range, press the direction keys, and the screen will not move.The indicator will flash with each effective keypress.

2. Auto Framing
   The camera has an auto-framing function. Press F1, the camera will start the auto framing function, and the camera will zoom in/ out to center all participants in the picture, according to the conference scene.
   Note: When the camera is under auto framing state, press F2 or the direction keys, zoom keys, and the auto framing state will end.

3. Set/Call the preset
   Long press the number key for more than 3 seconds to set presets. Short press the number key to call the presets, and the camera will quickly go to the presetting position& size.
   When setting the presets, the indicator light is always on after flashing once. And when calling the presets, the light flashes twice.

4. Menu Function
   After entering the menu, select the menu options via direction keys. Press the HOME key to enter the options, and adjust the options by using the pan button. Press the Menu key to return to the previous interface until the exit menu.

INSTALLATION

Installation Instructions

• The camera is mounted on the hinge bracket.
• Place the camera holder on the monitor and fix it to the monitor by adjusting the holder on the back.
• Please check whether the connection is correct before starting.

ANNEX 1 TECHNICAL SPECIFICATIONS

Camera

Image Sensor| 1/2.8″ CMOS, Progressive scan CMOS, 8.42 million pixels
Max. Resolution| 4KP30

Video Format

| YUY2, NV12:

1920x1080P30, 1280x720P30, 640x360P30

1920x1080P25, 1280x720P25, 640x360P25 MJPEG, H264, H265:

3840x2160P30, 1920x1080P30, 1280x720P30, 640x360P30

3840x2160P25, 1920x1080P25, 1280x720P25, 640x360P25

Digital Zoom| 4x
Focus Lens| f=2.1mm
Iris| F2.2
Field Of View| D：120.1°，H：109.7°，V：87°
Video Adjusts| Brightness, HUE, Saturation, Contrast, Sharpness
White Balance| Auto
Exposure Control| Auto
Intelligence| Auto framing and counts the number of people
---|---
S/N Ratio| ≥50dB
Menu| Support
PTZ
EPTZ| Support
Audio
Audio Input| Built-in dual MIC pick-up.
USB
USB Interface| 1×USB 3.0 Type-C
UVC| Support V1.0
UAC| Support
Operating System| Windows 7/8/10, Mac OS, Android OS, Linux
Conference Software| Zoom,Skype,DingTalk,Tencent Meeting, Google Meets,Teams， WebEx
General
Power Consumption| < 2.5 w
Power| DC5V(USB power supply), current ≤0.5A
Temperature| Working temperature: 0°C~+40°C Storage temperature: -20°C~+60°C
---|---
Working Humidity| 10%RH ~ 90%RH
Dimensions (W×H×D)| 210mm×74mm×48mm
Weight| ≤0.3kg
Color| Black

ANNEX2 SIZE AND DIMENSIONS

SIMPLE TROUBLESHOOTING

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>