laia Cute B&H Lite Full HD Bar for Small Rooms User Guide
- June 5, 2024
- laia
Table of Contents
Laia Cute B&H Lite Full HD Bar for Small Rooms
Appearance
This device i s a brand new model integrating an omni-directional microphone
and a wide-angle video camera. Operable without a drive, read ily portable and
easy to use, it is suitable for small meetings. It removes all constraints and
enables real-time communication anytime anywhere.
- Omni-directional Microphone
- Hd Wide-angle Lens
- Lens Indicator Light
- Microphone and Volume
- Ind actor Light
- Volume Up
- M icrophone
- ON/OFF
- Loudspeaker
- USB Port
Conection diagram
- Touch button function description
Volume increase touch button
Volume decrease touch button
Close or open the microphone touch buttons
- Electromagnetic fields at specific frequencies may affect the image of the machine.
- Do not hot-plug the power supply during the use of the IP Camera
Lamp State instructions
- Greenlight on: the microphone and speaker is working
- Red light on the microphone is mute, the speaker is working
- Greenlight flash: the volume’+”-‘ touch button is operating
- Greenlight slow flash: the microphone is working, the speaker is mute
- Red and green light slow flash alternately: the microphone is mute, the speaker is mute
- Lens lights on camera is working
DIP Switch
The “SW-1” and “SW-2” two DIP switch are set to OFF state, that is, select normal working mode
| DIP Switch | No. | SW-1 | SW-2 | Explain |
|---|---|---|---|---|
| 1 | OFF | OFF | Normal Mode | |
| 2 | ON | OFF | Upgrade Mode | |
| 3 | OFF | ON | Debug Mode | |
| 4 | ON | ON | — |
RS232 Interface
| Interface diagram | No. | Function | No. | Function |
|---|---|---|---|---|
| 1 | DTR | 5 | RXD | |
| 2 | DSR | 6 | GND | |
| 3 | TXD | 7 | IR OUT | |
| 4 | GND | 8 | NC |
Safety Precautions
Electrical safety
The installation and use of this product must strictly comply with local electrical safety standards.
Power polarity
This product uses DC+12V power, please pay attention to the power polarity.
Careful installation
Do not grab the camera head to move the camera.
Do not rotate head of camera by hand, it may cause mechanical problems.
Do not unauthorized disassemble
This product has no parts which can be repaired by the user. The damage caused
by the user’s own disassembly is not covered by warranty.
Troubleshooting
Image
-
The monitor shows no image
- Check that the camera power supply is connected, the voltage is normal, and the power indicator light is always on.
- Turn off the power switch to check whether the camera is self-testing.
- Check the two DIP switch of the camera bottom is set to OFF state.
- Check the cable of the video platform and TV to whether correct connection.
-
Sometimes without the image
Check the cable of the video platform and TV whether correct connection. -
Image has jitter when the camera lens is at max-multiple.
- Check whether the camera installed position is stable.
- Check whether have vibrating machinery or an object near the camera.
-
Control
The remote control can not control- Check and replace the new battery for the remote controller.
- Check whether the camera working mode is correct.
-
Series port can not control
- Check whether the camera protocol and address is the same.
- Check whether the control line is connected well.
Toxic and Harmful Substances
| (Pb)| (Hg)| (Cd)| (CrVI)| (PBB)| (PBDE)
---|---|---|---|---|---|---
Metal| x| Ο| Ο| Ο| Ο| Ο
Plastic| Ο| Ο| Ο| Ο| Ο| Ο
Glass| x| Ο| Ο| Ο| Ο| Ο
Circuit board| x| Ο| Ο| Ο| Ο| Ο
Power| x| Ο| Ο| Ο| Ο| Ο
Attached| x| Ο| Ο| Ο| Ο| Ο
This form is compiled in accordance with SJ/T 11364.
Ο: Indicates that the content of the hazardous substance in all homogenized
materials of the component is subject to the limit specified in GB/T 26572.
x: Said the hazardous substance in at least one of the components homogenized
material content in excess of the GB/T 26572 limit requirements, and there are
no mature alternatives.
Warranty Card
If failure caused by non-human causes occurs within one year from the date of purchase of the machine, you may enjoy the warranty service of the product. Any of the following circumstances is not covered by the warranty:
- Without disassembling, modification such as fault causes.
- The use of an environment does not conform to the requirements of the product.
- Irresistible factors, such as fire, earthquake, lightning strikes, etc.
The warranty card does not match the product number or it is altered
User save, lost or not compensated
Sales Department: (seal)
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>