D-Link DGS-3130-30TS Stackable Managed Switch Installation Guide
- June 6, 2024
- D-Link
Table of Contents
D-Link DGS-3130-30TS Stackable Managed Switch
Package Contents
Open the shipping carton of the Switch and carefully unpack its contents. The carton should contain the following items:
- One DGS-3130-30TS switch
- One AC power cord
- One console cable (RJ-45 to RS-232)
- One rack mounting kit (two brackets and screws)
- Four rubber feet with adhesive backing
- One power cord retainer set
- One Quick Installation Guide
LEDs
| LED | Status | Description |
|---|---|---|
| Power | Solid green | Device power on. |
| Light off | Device power off. | |
| Console | Solid green | Console on. |
| Light off | Console off. | |
| MGMT | Solid green | Link presents but not sending or receiving data. |
| Blinking | Port is sending or receiving data. | |
| Light off | No link or port was administratively shutdown. | |
| USB | Solid green | USB disk is connected. |
| Blinking | Data is transmitting. | |
| Light off | No device is connected. | |
| RPS | Solid green | RPS in using. |
| Light off | RPS off. | |
| Fan Error | Solid yellow | The fan has run time failure and is brought offline. |
| Light off | All fans work normally. | |
| Stack ID | Capable 1-8 | The Box ID is assigned in the stack. |
When the box becomes stacking master, the box ID and «H» will be shown by
turn. That is boxID -> H -> boxID -> H … off.
Link/Activity/Speed
(per 10/100/1000Base-T port)
| Solid green| When there is a secure 1000 Mbps connection at the port.
Blinking green| When there is reception or transmission occuring at the port.
Solid amber| When there is a secure 10/100 Mbps connection at the port.
Blinking amber| When there is reception or transmission occuring at the port.
Light off| No link.
Link/Activity/Speed (per 10GBase-T port)| Solid green| When there is a secure
10 Gbps connection at the port.
Blinking green| When there is reception or transmission occuring at the port.
Installation Guidelines
This section will discuss the hardware installation guidelines that the user must follow in order to properly and safely install this switch into the appropriate environment.
- Visually inspect the power cord and see that it is fully secured to both the power connector, on the Switch, and the electrical outlet that supplies power.
- Install the Switch in a fairly cool and dry place within the acceptable operating temperature and humidity ranges.
- Install the Switch in a site free from strong electromagnetic field generators such as motors, vibration, dust, and direct exposure to sunlight.
Installing the Switch without a Rack
This section is used to guide the user through installing the Switch in an
area other than a switch rack. Attach the included rubber feet to the bottom
of the Switch. Take note that there should be marked blocks on the bottom of
the Switch to indicate where to attach the rubber feet. These markings are
usually found in each corner on the bottom of the device. The rubber feet
cushion the Switch, protecting the casing from scratches and preventing it
from scratching other surfaces.
Attaching rubber feet to the Switch
Install the Switch on a sturdy, level surface that can support the weight of the Switch. Do not place any heavy objects on the Switch. The power outlet should be within 1.82 meters (6 feet) of the Switch. Make sure that there is proper heat dissipation and adequate ventilation around the Switch. Leave at least 10 cm (4 inches) of space at the front, sides, and rear of the Switch for ventilation.
Installing the Switch in a Standard 19” Rack
This section is used to guide the user through installing the Switch into a
switch rack. The Switch can be mounted in a standard 19″(1U) rack using the
provided mounting brackets. Fasten the mounting brackets to the sides of the
Switch using the screws provided. Fasten the mounting brackets in any
available open space in the rack using the screws
provided.
Figure 3 — Installing the Switch in a Rack
Installing Transceivers into the Transceiver Ports
The Switch is equipped with Small Form-factor Pluggable (SFP) and Enhanced
Small Form-factor Pluggable (SFP+) ports that can be used to connect various
other networking devices to this switch that do not support the standard RJ-45
wiring connection. These ports are generally used to connect this switch to
optical fiber connections and can be used to connect devices to the Switch
over great distances. The maximum distance that the RJ-45 wiring connection
can reach is 100 meters. Fiber optic connections can span several
kilometers.
Inserting transceivers into the transceiver ports
Power On (AC Power)
Plug one end of the AC power cord into the power socket of the Switch and the
other end into the local power source outlet. After the system is powered on,
the LED will blink green to indicate that the system is booting up.
Power Failure (AC Power)
In the event of a power failure, just as a precaution, unplug the power cord
from the Switch. After the power returns, plug the power cord back into the
power socket of the Switch.
Installing Power Cord Retainer
To prevent accidental removal of the AC power cord, it is recommended to
install the power cord retainer together with the power cord.
With the rough side facing down, insert the tie wrap into the hole below the
power socket.
Insert Tie Wrap into the Switch
Plug the AC power cord into the power socket of the
Switch.
Connect the power cord to the Switch
Slide the retainer through the tie wrap until the end of the
cord.
Slide the Retainer through the Tie
Wrap
Circle the tie of the retainer around the power cord and into the locker of
the retainer. Fasten the tie of the retainer until the power cord is
secured.
Secure the power cord
Installing the Redundant Power Supply (RPS)
The Redundant Power Supply (RPS) is designed to conform to the wattage requirements of D-Link’s Ethernet and Gigabit switches. It is an external RPS unit enclosed in solid metal case with sockets to connect AC or DC power sources on one end, and to connect to a switch’s internal power supply on the other end. The RPS provides a low-cost, simple solution to the problem of an inadvertent failure of the internal power supply of an Ethernet switch, which can result in the shutdown of that switch, the devices attached to its ports, or an entire network.
CAUTION: Do not connect the RPS to AC power before the DC power cable is
connected. This might damage the internal power supply.
CAUTION : Leave at least 15 cm (6 inches) of space at the rear of the
Switch when an RPS is installed to prevent cable damage.
DPS-500A Redundant Power Supply
This RPS (DPS-500A) can be connected to the Switch’s RPS port using a
14-pin DC power cable. A standard, three-pronged AC power cable connects the
RPS to the main power source.
Connecting a DGS-3130 Series Switch to the DPS-500A
Installing the RPS into a Rack-mount Chassis
DPS-800
The DPS-800 is a standard-size (1 standard unit in height) rack-mountable unit
designed to hold up to two RPS units.
NOTE: This rack-mount chassis supports the following RPS units: DPS-500A
and DPS-500DC.
Install the DPS-800 in an Equipment Rack
Management Options
This switch provides multiple access platforms that can be used to configure,
manage, and monitor networking features available on this switch. Currently,
there are three management platforms available which are described below.
Command Line Interface (CLI)
This switch can be managed, out-of-band, by using the console port or the MGMT
port on the front panel of the Switch. Alternatively, the Switch can also be
managed, in-band, by using a Telnet connection to any of the LAN ports on the
Switch. The command-line interface provides complete access to all switch
management features.
SNMP-based Management
The Switch can be managed with an SNMP-compatible console program. The Switch
supports SNMP v1, SNMPv2c, and SNMPv3.
Web User Interface (Web UI)
The Web UI can be accessed from any computer running web browsing software
from its MGMT port, or LAN port when it is connected to any of the RJ-45 or
SFP/SFP+ ports. The Web UI on the Switch can also be accessed using an HTTPS
(SSL) connection. This management interface is a more graphical representation
of the features that can be viewed and configured on this Switch. Most of the
features available through the CLI can be accessed through the Web UI. Web
browsers like Microsoft’s Internet Explorer, Mozilla Firefox, or Google Chrome
can be used.
Connecting to the Console Port
The front panel of the Switch provides an RJ-45 console port to connect a remote system for monitoring and configuring the Switch. To use the RJ-45 console port, the following equipment is needed:
- A terminal or a computer with both an RS-232 serial port and terminal emulation software
- A console cable with a male DB9 connector on one end and an RJ-45 connection on the other
To connect the RJ-45 console port on the Switch to the computer:
- Connect the male DB9 connector on the console cable (shipped with the Switch) to the RS-232 serial port on the computer running terminal emulation software then insert the RJ-45 connector into the RJ-45 console port on the front of the Switch.
To configure the terminal emulation software as follows:
- Select the appropriate serial port (COM1 or COM2).
- Set the data rate to 115200 baud.
- Set the data format to 8 data bits, 1 stop bit, and no parity.
- Set flow control to none.
COM Port Configuration
To be able to view the boot procedure, the Switch needs to be rebooted. The
simplest way, at this stage, to reboot the Switch is to unplug and re-insert
the power cable from and into the power receptacle on the back of the Switch.
After correctly configuring the terminal settings and re-inserting the power
cable, the boot procedure will appear in the terminal.
After the boot sequence has been completed, the console login screen will be displayed.
Connecting to the Switch for the First Time
By default, there is no Username and Password configured in the account
settings of this switch. This will allow the user to simply connect to this
Switch for the first time by pressing the ‘Enter’ key. After pressing Enter,
access will be given to enter commands after the command prompt (Switch>)
appears.
NOTE: The first user automatically gets Administrator level privileges.
At least one Administrator-level user account must be created for the Switch.
NOTE: It is highly recommended to create a user account containing a
username and a password on the Switch to prevent unauthorized access to the
management interface.
Connecting to the MGMT Port
The front panel of the Switch features an Out-Of-Band (OOB) RJ-45 MGMT port
which can be used to connect to a computer using a standard Ethernet cable. A
web browser or Telnet client can be used to connect to the Switch using the
MGMT port. To use the MGMT port, connect one end of an Ethernet cable to a
computer and the other end to the Switch. The default IP address of the MGMT
port is 192.168.0.1 and the subnet mask is 255.255.255.0. Make sure that the
computer being used for the switch management has a non-conflicting IP address
in the 192.168.0.0/24 network.
To view the IP settings of the MGMT port, use the following
command:
The IP settings or enabled status of the MGMT port can be changed through the
console port. For example, to change the IP address of the MGMT port, use the
following commands:
Logging into the Web UI
Supported Web browsers:
- Microsoft Internet Explorer 7 or above
- Firefox
- Google Chrome
- Safari
To access the Web UI, open a standard web browser, enter the Switch’s IP
address into the address bar of the browser, and press the ENTER key. To
access the Web UI from normal LAN ports, the default IP address is
10.90.90.90. When connecting to the Web UI of the Switch for the first time,
leave the User Name and Password fields blank and click Login since there are
no login user accounts created by default on this
switch.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>