KBDCRAFT 01001 Built Keyboard Instruction Manual
- June 12, 2024
- KBDcraft
Table of Contents
KBDCRAFT 01001 Built Keyboard
Product Information
Product Name: KBDCRAFT 01001 Kit Adam
Instruction Manual Version: 3.0
Components
- Stabi x4
- 05001 Stabi (requires lubrication)
- 05002 JWK Stabi (pre-lubed)
- Plate
- Poron Piece
- PCB (type-a, hot swappable, 1.6mm, screw-in-stabilizer compatible)
- Switch POM Plate
- Poron Foam Case
- Gaskets (10x)
- Core
- Rubber Feet
- Keycaps
- VIAL (software)
- 08001 Wrist Rest (optional accessory)
- 01002 Kit Addams (additional kit, not included in this manual)
Product Usage Instructions
Stabilizers (Stabi)
-
Check the stabilizers to ensure they are well put
together. -
Place the Stabis on the Plate, aligning the wire towards the
notch. -
Push the wire in first, then push the back end down. Ensure the
snaps are engaged. -
Lubricate the 05001 Stabi with the provided grease, especially
the contact area of the wires. Be careful with the stems when
reassembling them. -
The 05002 JWK Stabi is pre-lubed, so no additional lubrication
is required.
Core Assembly
- Align the Plate, Poron piece, and PCB to create a sandwich.
- Finish the Core assembly by installing the switches.
- If using PCB type-a, ensure it is designed for a modular keyboard. Also, check the PCB function before assembly.
Case Assembly
- Put the gaskets on the case (10x).
- Insert the Core into the case.
- Attach the rubber feet to the case and check if it sits properly.
Keycaps
Note: It has a 2U left shift key.
VIAL Software Installation
- Open a browser and go to get.vial.today.
- You can either use the VIAL Web version or download VIAL from the website.
- When connected, the keyboard will be recognized as Adam0110 and the map will be loaded.
Testing and Configuration
- Test the installation result with the matrix tester to ensure all buttons light up.
- The key value and RGB lights are configurable. Press Fn to activate shortcut keys of the layer (1) for backlight mode and on/off control.
Modularity: The product supports modularity with additional kits such as 01002 Kit Addams (not included in this manual).
Optional Accessory: 08001 Wrist Rest can be purchased separately.
Manufacturer: SHANGHAI, EST. 2021
Stabi
-
Check the stabilizers. Make sure they’re well put together.
-
Lubricate the 05001 Stabi with the grace provided, especially the contact area of the wires. Be careful with the stems when you reassemble them.
*The 05002 JWK Stabi is pre-lubed. Therefore no lube is offered. -
Put the Stabis on the Plate. Align the wire towards the notch. Push the wire in first. Then push the back end down. Make sure the snaps are engaged.
-
Align the Plate, Poron piece, and PCB as making a sandwich. Finish the Core by installing the switches.
Core
*PCB type-a is designed for modular keyboard **Check the PCB function before assembly.
Case
Keycaps
vial
- Open a browser.
- Key in: get.vial.today then you can use the VIAL Web version or download VIAL.
- The keyboard will be recognized as Adam0110. The map will be loaded after you click connect.
- Test the installation result with the matrix tester. Make sure all buttons light up. vial
- The key value and RGBs lights are configurable.
Modularity
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>