SOMMER S10560 Pearl Twin 2-Button Transmitter Instruction Manual

SOMMER S10560 Pearl Twin 2-Button Transmitter

Technical data

Weight

Battery

| approx. 30 g including batteries

CR 2032

Safety instructions

WARNING

There is a risk of injury or even death if the safety instructions are not followed!

•  These instructions must be read, understood, and complied with by persons installing, operating, or performing maintenance on the radio system!
•  These instructions are important and must be made available to all users!
•  The unit may not be modified!
•  Always have faulty devices repaired by a technician authorized by the manufacturer!
• Devices that pose a risk of accident may not be operated via remote control unless the complete range of movement of the system is visible to the user! The local safety regulations for this system must be complied with to ensure safe operation!
• This device complies with Part 15 of the FCC Rules and contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science, and Economic Development Canada’s license-exempt RSS standard(s).
• Operation is subject to the following two conditions:
  this device may not cause harmful interference, and ( this device must accept any interference received, including interference that may cause undesired operation.
  Changes or modifications made to this equipment not expressly approved by SOMMER Antriebs- und Funktechnik GmbH may void the FCC authorization to operate this equipment.

NOTE:

•  This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

• If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct
  the interference by one or more of the following measures:

•  Reorient or relocate the receiving antenna.

•  Increase the separation between the equipment and receiver.

•  Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

•  Consult the dealer or an experienced radio/TV technician for help.

Intended use

•  Only use the hand-held transmitter together with radio receivers from SOMMER Antriebs- und Funktechnik GmbH.
•  The hand-held transmitter is suitable for SOMloq Rollingcode and SOMloq2 radio systems.
• The hand-held transmitter must only be used for devices and systems in which radio interference in the transmitter or receiver will not endanger people, animals or objects, or the risk is reduced by other safety devices.
• Remote control of devices and systems with increased accident risk (e.g. hoists) is prohibited.

Programming the hand-held transmitter on a radio receiver See the instructions for the radio receiver or the operator for the correct procedure for selecting the desired channel on the radio receiver, setting it in programming mode and the correct response of the LED on the radio receiver at the various phases of the programming process.

• Select the desired channel on the radio receiver and set in programming mode. Press the desired hand-held transmitter button (A).
•  LED on the hand-held remote control lights up red.
•  Radio command is transmitted.

Operation

Requirements

• The desired radio command is programmed on the desired radio receiver.
•  Hand-held transmitter battery is not empty.

SOMloq2 functions
The functions can only be used when a SOMloq2 radio receiver is used as the radio receiver.

Auto-repeat function
This function makes it possible to give the radio command before the transmitter is in the range of the radio receiver. The transmitter then automatically repeats the command up to 5 times, every 3 seconds.

• Press the hand-held transmitter and keep it pressed for 1 to 3 seconds.
•  The hand-held transmitter now sends the command automatically every 3 seconds (maximum 5 times).

Hop function
The Hop function increases the range of the radio system because the SOMloq2 radio receiver which is located in the range of the transmitter actively forwards the command.

Battery change

Warning information

WARNING

There is a risk of injury or even death if the safety instructions
are not followed!

•  These instructions must be read, understood and complied with by persons installing, operating or performing maintenance on the radio system!
•  These instructions are important and must be made available to all users!
•  The unit may not be modified!
•  Always have faulty devices repaired by a technician authorized by the manufacturer!
• Devices that pose a risk of accident may not be operated via remote control unless the complete range of movement of the system is visible to the user!The local safety regulations for this system must be complied with to ensure safe operation!
• Never spray the device using a hose or high-pressure washer. Water may penetrate into the device and damage or destroy the radio remote control!

1.  Remove screw from lower housing section.
2.  Lift upper housing section.
   • Replace battery.
3.  Put the upper housing section back on.
   •  Make sure that the lower housing section is hooked into the upper section as shown.
4.  Fasten the screw into the lower housing section.

Troubleshooting

•  LED does not light up: Battery dead or hand-held transmitter faulty.
•  The operator does not start:
•  Hand-held transmitter not programmed.
•  The hand-held transmitter has been activated several times outside of the reception area – press the button (min. 2 x ) until the operator starts.

Disposal

Observe applicable national regulations.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>