SOMMER Telecody Plus S12872-00024 Wireless Keypad Instruction Manual

June 12, 2024
SOMMER

SOMMER Telecody Plus S12872-00024 Wireless Keypad

Product Information

The Telecody+/Courier is a radio frequency device used for transmitting radio commands after the input of a numeric code or pressing a button. It has a range of communication and is designed for various applications.

Technical Data

  • Radio frequency: [Radio frequency]
  • Temperature range: [Temperature range]
  • Radio commands: [Number of radio commands]
  • Range: [Range]
  • Protection class: [Protection class]
  • Dimensions (housing): [Dimensions]
  • Weight: [Weight]
  • Battery: [Battery]

Terms

The Telecody+/Courier operates based on certain terms:

  • Radio command: The device sends a radio command after the input of a valid access code.

  • Access code: A number or number sequence (0-9) entered on the
    keypad to activate a radio command. The device allows coding of 10 commands.

  • Active time: The duration during which the previously sent radio command is repeated by pressing any number button.

Courier Function

The Telecody+/Courier has a special courier function that opens the door to a specific height, allowing parcel delivery. It requires a numeric code known as the courier code.

Area of Use / Purpose

The Telecody+/Courier can be used for various applications that require the transmission of radio commands after the input of a numeric code or pressing a button.

Product Usage Instructions

Switching On

Before initial commissioning, the Telecody+/Courier must be enabled.

Programming to Receiver

Follow the receiver/operator instructions for programming the Telecody+/Courier to the receiver. The process involves:

  1. Set the receiver to programming mode.
  2. Enter the desired radio command/access code using buttons 0-9.

Changing Access Code

To change the access code, follow these steps:

  1. Press button P.
  2. Enter the old access code.
  3. Press button P again.
  4. Enter part 1 of the new access code by pressing the
    corresponding buttons.

Deleting Access Code from Radio Command

If you want to use a radio command without an access code, follow these steps:

  1. Press button P.
  2. Enter the old access code.
  3. Press button P again.
  4. Enter part 1 of the access code by pressing the corresponding
    button(s).

Resetting to Factory Settings

To reset the Telecody+/Courier to factory settings, follow these steps:

  1. Press button M.
  2. Press button P.
  3. Enter the 9-digit reset code (refer to the sticker).
  4. Press button M again.
  5. Press button P again.

Operation

The Telecody+/Courier operates by transmitting radio commands after the input of a numeric code or pressing a button.

Requirements

The device requires a valid access code and proper setup with the receiver/operator.

Intended Use

The Telecody+/Courier is intended for transmitting radio commands in various applications.

Explanation of Display and Buttons

Refer to the product manual for detailed information on the display and buttons of the Telecody+/Courier.

INSTALLATION

SOMMER-Telecody-Plus-S12872-00024-Wireless-Keypad-fig5

Technical data

Radio frequency 922,5 MHz
Temperature range -20 °C …+55 °C
Radio commands 12 (10 with access code,

2 without)

Range| 50 m
Protection class| IP 64
Dimensions (housing)| 147 x 44 x 30 mm
Weight

Battery

| 180g including batteries

Type CR123A (3V)

Terms

Radio command| The Telecody+/Courier sends the radio command after input of a valid access code.
---|---
Access code| Input of a number or number sequence (0 …9) on the keypad.
Active time

Courier function*

Courier code*

| Time during which the previously sent radio command is sent again by pressing any number button.

The door opens to a specific height, for example to allow a parcel delivery .

Numeric code for the courier function.

Only available with the special version of the Telecody+ (Telecody Courier)

Area of use / purpose

  • Suitable for radio systems with Somloq Rollingcode and SOMloq2.

Reset code sticker
Keep the sticker with the reset code in a safe place. The reset code is required to delete all programmed access codes, e.g. if the access code has been forgotten.

Functional description

  • The Telecody+/Courier sends a radio command to a receiver after input of the correct access code.
  • If the receiver is a SOMloq2 radio receiver, the receipt of the radio command is confirmed, and LED 1 on the Telecody+/Courier lights up.

Safety instructions

WARNING
There is a risk of injury or death if the safety instructions are not followed!

  • These instructions must be read, understood and complied with by persons who install, use or perform maintenance on the radio remote control.

  • Please read and follow all instructions in this manual as well as the information for each receiver you are planning to operate with this device.

  • Please share this important information with other users.

  • Have faulty devices repaired by a technician authorised by the manufacturer.

  • Systems that pose an accident risk should not be operated by remote control unless the complete range of movement of the system is visible to the user.

  • The local safety regulations for the system must be observed to ensure safe operation.

  • The radio remote control must never be sprayed with a water hose or high-pressure washer. External voltage can trigger severe power surges and damage or destroy the radio remote control.

  • Use only original equipment manufacturer (OEM) parts and accessories as well as fixing supplies.
    NOTICE:

  • This device complies with Part 15 of the FCC Rules and contains license-exempt transmitter(s)/ receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS standard(s).
    Operation is subject to the following two conditions:

    • (1) this device may not cause harmful interference, and
    • (2) (this device must accept any interference received, including interference that may cause undesired operation.
  • Changes or modifications made to this equipment not expressly approved by SOMMER Antriebs- und
    Funktechnik GmbH may void the FCC authorization to operate this equipment.

  • NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.

  • Increase the separation between the equipment and receiver.

  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

  • Consult the dealer or an experienced radio/TV technician for help.

CAUTION

Intended use

Transmission of radio commands after entry of a numeric code or pressing a button.
Explanation of display and buttons

Optical display

LED 1 (1)

• Briefly lights up orange when a radio command is transmitted
• Lights up green for 1 second if a response from a SOMloq2 radio receiver has been received
• Blinks red during transmission if the battery charge is low
LED 2 (2)

  • Briefly lights up orange during button inputs

  • Blinks for:

    • Reset message
    • Active time
    • Transmission delay
  • Blinks briefly during keypad input when the Telecody+/Courier is locked
    LED (1) + (2)

  • Light up for 2 seconds while:

    • Programming an access code
    • Deleting all access codes
    • Switching active time on/of

Buttons

Numbers 0 – 9 •  Entry of access codes
ESC Correction of an incorrect input

•  Stop active time

•  Cancel input

•  Switch keypad light off

M| Memory button

•  Switching active time on or off

•  Reset to factory settings (in combination with P button)

●| Dot button

•  Send uncoded radio command

•  Switch keypad light on*

○|

*Not in combination with the courier mode without code (only with red key)

Radio commands

The Telecody+/Courier can send 12 radio commands directly by pressing a button. 10 commands (numbers 0 – 9) can be coded.SOMMER-Telecody-
Plus-S12872-00024-Wireless-Keypad-fig9

Switching on

The Telecody+/Courier must be enabled before initial commissioning.

  1. Press and hold button M.
    • LED 2 flashes three times.
    • Then LEDs 1 + 2 light up for two seconds.
    • Backlighting is switched on.

Programming to receiver

See the instructions for the receiver/operator for information on the receiver.

  1. Set receiver to programming mode.
  2. Enter the desired radio command/access code
    • Buttons 0 – 9 and ●○can be used.
      The buttons ●○ cannot be programmed with an access code.

Programming access code

An access code consists of 2 parts with a total of 8 characters.

Part 1 (character 1)
desired radio command must be input every time the access code is entered
Part 2 (character 2 – 8)
desired access code (freely selectable)

Example of access code for radio command 1 1 8 3 5

  1. Press button P.
  2. Press button 1.
  3. Press button P again.
    • Radio command 1 is selected.
  4. Enter part 1 of the access code:
    • Press button 1.
  5. Enter part 2 of the access code:
    • Press button 8.
    • Press button 3.
    • Press button 5.
    • Press button P.
    • LEDs 1 + 2 light up for 2 seconds.
    • The access code for radio command 1 is now: 1835
  6. Enter 1835 to check the access code.
    • LED 2 lights up briefly.
    • LED 1 lights up (with SOMloq2 radio receivers as confirmation of receipt)
    • Access code successfully programmed.

Changing access code

Example: The above access code 1835 is changed to 194686

  1. Press button P.
  2. Enter old access code: 1835.
  3. Press button P again.
  4. Enter part 1 of the access code:
    • Press button 1.
  5. Enter part 2 of the access code:
    • Press button 9
    • Press button 4
    • Press button 6
    • Press button 8
    • Press button 6
    • Press button P.
    • LEDs 1 + 2 light up for 2 seconds.
    • The access code for radio command 1 is now: 194686.
  6. Enter 194686 to check the access code.
    • LED 2 lights up briefly
    • LED 1 lights up (with SOMloq2 radio receivers as confirmation of receipt)
    • Access code successfully programmed.

Deleting access code from radio command
For example, if radio command 3 is protected by an access code and is to be used without a code in future:

  1. Press button P.
  2. Enter old access code.
  3. Press button P again.
  4. Enter part 1 of the access code:
    • Press button 3.
  5. Press button P.
    • LEDs 1 + 2 light up for 2 seconds.
    • Radio command will now be sent by pressing button 3 alone without requiring an access code.

Resetting to factory settings

This will delete all programmed access codes.
The Telecody+/Courier remains activated.

  1. Press button M.
  2. Press button P.
  3. Enter 9-digit reset code (see sticker).
  4. Press button M again.
  5. Press button P again.
    • LEDs 1 + 2 light up orange for 2 seconds.

Operation

Requirements

  • The Telecody+/Courier is switched on.

  • Telecody+/Courier is programmed to the required radio receiver

  • Access codes are programmed.

  • Telecody+/Courier battery is not flat.
    Input of a valid access code or pressing the ● or ○ button sends a radio command to the programmed receiver, which, for example, opens or closes a garage door.

    • During transmission of a radio command LED 1 lights for 2 seconds.
    • LED 1 lights up (with SOMloq2 radio receivers as confirmation of receipt)

Active time

Delivery status deactivated.

Description
During the active time (lasts for 20 seconds), press any number button:

  • The previously transmitted access code is sent again (without entering the access code again).
  • The active time is restarted for 10 seconds.

Activate/deactivate

  1. Press button M.
  2. Press ● button.
  3. Press button M.
    • Active time is switched on or off

Status query
The user can check whether the active time is activated:

  1. Enter valid access code.
    • LED 1 lights up.
    • Radio command is sent.
    • LED 2 blinks for 20 seconds:
    • Active time is activated.
    • LED 2 does not blink:
    • Active time is deactivated.

Transmission delay

Delivery status deactivated.
The radio command is sent with a delay of 1 – 9 seconds.
Setting range 0 – 9 (0 = no transmission delay). The transmission delay is applicable for all radio commands.
Activate/deactivate

  1. Press button M.
  2. Press button ○.
  3. Enter the desired transmission delay on the keypad (1 – 9 s).
  4. Press button M
    • LEDs 1 + 2 light up orange for 2 seconds.

Courier function (Telecody Courier)

The courier function allows a garage door equipped with a SOMloq2 operator to be opened to a defined height (opening height), for example so that a parcel can be pushed through.
Only available with the special version of the Telecody+ (Telecody Courier). On this version, the ●○ button is red

  • For security reasons, all access codes must be programmed before activating the courier function. A factory reset is required in order to program further access codes.
  • Most parcel delivery services offer the option of providing information for parcel delivery (safe place for deposit, numeric code etc.). This information can be sent to the parcel delivery service as a permanent delivery preference (after registration) or for one specific delivery (after notification of pending delivery).

You can choose between two different versions of the courier function:

With code
With this version, the door opens after a numeric code is entered. This option offers a high degree of security against unauthorised use.

Without code
With this version, the door is opened simply by pressing the red button (either ● or ○ . There is no protection against unauthorised use.

Procedure

  1. Enter courier code or press the red button (either ● or ○).
    • Door opens to the set opening height.
    • LED 2 blinks until the door closes again (15 sec).

Programming defined opening and closing
First, on the operator (see instructions for the operator), program Defined opening/closing using the red button (● or ○).

  • Radio/channel/Function Symbol
  • 3/Defined opening/●
  • 4/defined. closing/○

Activating the courier function on the Telecody Courier

1. Press buttons P and M simultaneously and hold them pressed for 5 seconds.
Î LED 2 blinks orange during the process.
Î LEDs 1 + 2 light up orange for 2 seconds.

Programming the courier function with entry of a numeric code (courier code)
Precondition is a programmed access code, see

„Programming access code“.

  1. Press red button (either ● or ○) and hold it pressed throughout the process.
  2. Enter access code.
    • LEDs 1 + 2 blink green alternately.
    • Following correct entry of the access code, LEDs 1 + 2 blink orange alternately.
  3. Enter the desired courier code*.
  4. Release the red button.
    • LEDs 1 + 2 light up orange for 2 seconds. *The courier code must be between 2 and 8 digits.

Activating courier function by pressing the red button alone

The delivery service employee does not need to enter a courier code.

  1. Press red button (either ● or ○) and hold it pressed throughout the process.
  2. Enter access code.
    • LEDs 1 + 2 blink green alternately.
    • Following correct entry of the access code, LEDs 1 + 2 blink orange alternately.
  3. Enter sequence of figures 00.
    • LEDs 1 + 2 light up orange for 2 seconds.

Deactivating the courier function e.g. in the case of prolonged absence

  1. Press red button (either ● or ○) and hold it pressed throughout the process.
  2. Enter access code.
    • LEDs 1 + 2 blink green alternately.
  3. Make no further entry.
    • LEDs 1 + 2 blink orange alternately.
  4. Release the red button.
    • LEDs 1 + 2 light up orange for 2 seconds.
    • Courier function is deactivated.
    • Any defined courier codes are deleted.

Proceed as described above to activate the function again.

Changing the opening height
The duration of the door movement defines the opening height. The longer the movement, the greater the opening height.

  1. Press button P.
  2. Press red button (either ● or ○).
  3. Enter the desired duration of door movement via the keypad (e.g. 3 = 3 seconds). (Setting range 3 – 9 seconds)
  4. Press button P
    • LEDs 1 + 2 light up orange for 2 seconds.
    • Opening height has been adjusted.

Replacing battery

WARNING

  • Never leave batteries within reach of children. Call a doctor immediately if a battery is swallowed.
  • Do not open or recharge the battery or allow it to come into contact with water, fire or high temperatures.
  • Replace battery only with CR 123A (3V).
  • Dispose of the battery according to locally applicable regulations.
  1. Pull off screw cover (3).
  2. Unscrew screw (4).
  3. Rotate Telecody+ and unscrew the bottom screws (5).
  4. Lift bottom section of housing.
  5. Replace the battery (6).
    Proceed in reverse order to reassemble.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals