GRAUGEAR G-M2DK-CL-20G USB 3.2 Gen Clone Station Instruction Manual

GRAUGEAR G-M2DK-CL-20G USB 3.2 Gen Clone Station

Package Contents

Features

• Supports PCIe x4 data transfer rates up to 20Gbps
• Bootable SSD cloning, without PC (stand-alone)
• Compatible with M.2 NVMe SSD size of 2230, 2242, 2260, 2280, 22110
• Supports PCIe NVMe M.2 SSD of M-Key
• 60mm fan for active cooling
• Premium aluminum heat sink with excellent cooling effort
• One-Key offline clone
• LED indication of the cloning progress
• LED indicator for power and access
• Power adapter 5V / 2A
• Supports Windows® and MacOS®

Specification

• Interface: M.2 M-Key
• External interface: USB3.2 Gen2x2 Type-C®
• Controller: JMS586U
• Supports SSD: M.2 NVMe SSD lengths: 2230, 2242, 2260, 2280 and 22110
• Transfer speed : PCIe USB3.2 Gen2x2 up to 20Gbit/s (Theoretic)
• Product material: Plastic / Aluminum
• Dimensions: L82 x W77 x H133mm
• Cable length: 35cm / 13.78 inches

Startup with SSDs

1. Install thermal silicon, M.2 SSD,  and heatsink.
2. Put the aluminum alloy radiator on two Rubber Rim.
3. Insert the M.2 SSD card into the slot.
4. Insert the transparent protective tube into the clone station.
5. Connect the power adaspter. If no use stand-alone clone function please connect the USB data cable with the computer.

Do not install any disks while the device is powered.

TARGET SOURCE: Please make sure the capacity of the target SSD is larger than the source SSD or same larger than the source SSDD, otherwise the clone function will not work.

Product Overview

Top

Back

Desktop/Notebook Clone Station Mode

1. Insert M.2 NVMe SSD to Slot (Source Drive) or (Target Drive) or both simultaneously.
2. Connect the device with SuperSpeed USB 3.2 Gen2x2 Cable to any Desktop or Notebook
3. Connect the Power cord and turn on the device.
4. Go to Disk Management to format the M.2 NVMe SSD
5. Ensure the you properly and Safely Remove the USB Device to allow both slots to turn off
   Note : Formatting is necessary for only NEW SSD, any damage caused during operation will be personal liability.

Instructions for Stand-Alone-Cloning
(only works if the clone station is not connected to the pc.)

1. Before you start cloning, seperate the usb cable from the device.
2. Now insert the Source-SSD in the slot [SOURCE] and the Target-SSD in the slot [TARGET] ein.
3. Connect the power adaptor in the power outlet and turn the Clone Station on.
4. Press and hold the Clone Button for at least 5 seconds, until the four conling progression LED´s 25%-100% start blinking in a row back and forth.
5. Press the clone button again and the clone progression LEDs blink again.
6. As soons as the 25% LED is glowing constantly, the cloning process starts. The LEDs show the cloning progress. The cloning time depends on the capacity oft he SSD.
7. As soon as the 100% LED is glowing and not blinking anymore, the cloning process is finished. Please, turn of the Clone Station before removing any SSD.

Clone Notes

1. The clone function creates an identical copy of your hard drive – no need to connect to any computer.
2. You can copy a bootable system disk without additional software or professional skills.
3. Since the cloning process copies every single byte of the source SSD the process may take several hours depending on the SSD capacity.
4. After the cloning process is completed, in some cases the computer may not be able to identify both SSD since they are assigned to the same drive letter. To separate the drives, you must assign one drive to a new drive letter under “disk management” (Windows).
5. If only one SSD is plugged into slot (SOURCE), and there will be no action when you press the start button.
6. The capacity of the target SSD must be the same size or larger than source SSD.
7. You may create a new volume with the remaining space on the target SSD after cloning.

Using A Brand New Hard Drive

lf you are using a brand new drive, you might have to initialize it before you can use it. Only initialize a disk if you are absolutely sure it is a brand new one with out any of you data.

Open Computer Management >> Storage Disk Management, then right-click on the disk you want to initialize, and select Initialize Disk on the drop-down menu. Please make sure that the correct disk is selected.

Drive is Connected but Missing in File Explorer
Open Computer Management >> Storage Disk Management, then right-click on the disk marked as Offline and select Online on the drop-down menu.

Safety information

For your own safety and to avoid physical damage as well as damage to property, equipment and loss of data, please observe the following instructions

Warning signs:

• You will be alerted to an imminently hazardous situation which may result in serious injury or even death!
• You will be alerted to a potentially dangerous situation that could result in serious injury, even death!
• You will be alerted to a potentially dangerous situation that may result in minor injury!
• Your attention is drawn to a possible situation that could result in property damage and possibly environmental damage and disrupt operations.

1. Dangers due to electric current and voltage!

   • Avoid any contact with electrically conductive parts, there is a danger to life due to electric shock.
   • Please read the operating instructions before use.
   • Make sure the product is not energized before opening or working on it.
   • Please do not remove the contact protection cover under any circumstances.
   • Avoid contact with live parts.
   • Do not touch any plug-in connectors with metallic or pointed objects.
   • Use the product only in designated environments.
   • If necessary, operate the product only with power supplies that correspond to the nameplate.
   • Do not expose the product or power supply to moisture and liquid, steam and dust.
   • Do not make any independent modifications to the product.
   • Do not connect/use the product during a thunderstorm.
   • In case of repair, please contact the specialist dealer or GrauGear.

2. Possible dangers during assembly due to sharp-edged components!
   Cutting and hand injuries possible during assembly.

   • Please read the operating instructions before assembly.
   • Avoid contact with sharp or pointed objects.
   • Do not use force during assembly.
   • Only use suitable tools or supplied accessories and tools.

3. Danger of heat generation due to insufficient ventilation of the product/power supply!

   • In this case, overheating and/or failure of the product/power supply unit is possible.
   • Avoid external heat supply and provide air exchange.
   • Keep fan outlets and heat sinks free.
   • Avoid direct sunlight on the product/power supply.
   • Make sure there is enough environmental space for the product/power supply.
   • Do not place any objects on the device/power supply.

4. Danger of suffocation! Danger due to small parts and packaging!
   Danger to life due to choking and swallowing.

   • Please be sure to read the instructions for use.
   • Keep small parts and accessories safe from children.
   • Keep and dispose of plastic bags and packaging from children.
   • Never put small parts and packaging into children’s hands!

5. Possible data loss / data loss during commissioning

   • Please be sure to read the operating instructions.
   • Use the product only if all specifications and requirements are met.
   • Always perform a data backup of storage media to be installed.
   • Always perform a data backup before commissioning.
   • Always perform a data backup before connecting new hardware.
   • Only use the accessories supplied with the product.

6. Cleaning of the product
   Damaging cleaning agent – scratches, color changes, moisture damage or short circuit on the device.

   • Take the product out of operation before each cleaning.
   • Do not use aggressive/harsh cleaners.
   • Make sure that there is no residual moisture in the device after cleaning.
   • It is best to use an antistatic cloth for cleaning.

7. Disposal of the product – environmental pollution, recycling not possible!
   “The adjacent symbol on the product and packaging indicates that this product must not be disposed of with other household waste. If necessary, remove old batteries, rechargeable batteries and lamps before returning the product (if possible without destroying the old device and if it is not to be reused). According to the Waste Electrical and Electronic Equipment (WEEE) Directive, you may not dispose of this product and any batteries/rechargeable batteries it may contain in your normal household waste. If you wish to dispose of this product/batteries, please take them to a suitable disposal point (recycling collection point in your city) or return them to your point of purchase.”

If you have any questions, please do not hesitate to contact our support at support@graugear.de or visit our website www.graugear.de

Documents / Resources

| GRAUGEAR G-M2DK-CL-20G USB 3.2 Gen Clone Station [pdf] Instruction Manual
G-M2DK-CL-20G USB 3.2 Gen Clone Station, USB 3.2 Gen Clone Station, Gen Clone Station, Clone Station, Station
---|---

References

• GRAUGEAR - USB Enclosures, USB Adapters, USB Hubs, M.2 SSD Cooling and PS5 SSD Heatsink more

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>