SOUNDPEATS A6 Hybrid Active Noise Cancelling Over Ear Headphone User Manual
- June 6, 2024
- SoundPEATS
Table of Contents
SOUNDPEATS A6 Hybrid Active Noise Cancelling Over Ear Headphone
MANUFACTURER
Shenzhen SoundSOUL Information Technology Company Limited
Room 1308-1309, Building B, Huihai Square, Chuangye Road, Longhua District,
Shenzhen, China. 518109
support@soundpeatsaudio.com
www.soundpeatsaudio.com
Company： Qing UG(haftungsbeschränkt)
Address: Undinestr. 7, 12203 Berlin Germany
PACKING LIST
PRODUCT OVERVIEW
- ANC Switch
- ANC Switch Indicator Light
- MIC
- AUX Interface
- LED Indicator Light
- Power Switch
- Volume Down
- Volume Up
- Charge Indicator Light
- USB-C Charge Interface
POWER ON/OFF, ANC SWITCH
Power On: Long press the power button 3s, the blue LED light will be
steady on 2s and then go off after flash slowly once.
Power Off: Long press the power button for about 4s, the red LED light
will up 2s and then go out.
ANC On: Short press the ANC button once, and the ANC blue indicator
lights up. ANC Off: Short press the ANC button once, and the ANC blue
indicator lights goes off.
Note: In order to avoid the failure of the power switch to the greatest extent, it is recommended to wait for 2-3 seconds to restart again after turn off the headphone.
BLUETOOTH PARING
- Long press the power button 3s in the power-off state to hear power on. After 5s, hear paring enter the pairing mode, and the indicator light flashes alternately in red and blue.
- After the first connection, the headset will automatically connect back to the last connected device when it is turned on;
- If you want to change the device or enter forced pairing, long press the power button 5s in the power off state;
- Reset: Under the power-on and non-talking state, long-press the power button and the sound plus button 5s at the same time, until the purple light comes on 2s and then goes out completely, hearing two “beep”, clear the pairing records and then enter the pairing state.
CONTROL
| Mode | Function | Operation Methods |
|---|
Bluetooth Mode
| Play/Pause| Short press the power button once
Previous Track| Long press “—” button once
Next Track| Long press “+” button once
Volume Up| Short press “+” button once
Volume Down| Short press “—” button once
Activate Voice Assistant| Long press the power button for 2s and then release
Calling Mode| Answer/Hang up a call| Short press the power button once
Reject a Call| Long press the power button 2s
Redial Last Number| Double-click the power button to redial the last call
Voice Transfer| In the call state, long press the power key 2s and then the
call sound is switched between the headset and the mobile phone
AUX-IN
- Inserting the audio cable will automatically switch to AUX mode. Long press the power key 3s and then short press the ANC key to enable the ANC function in AUX mode.
- In AUX mode, the functions of increasing/decreasing volume, pausing play, previous /next track on headphones will be invalid, which needs to be operate through the mobile terminal and corresponding APP.
CHARGE
The red light keeps on when charging, and the green light keeps on after fully charged.
WARRANTY REGULATIONS
We begin to guarantee the headset for a period of 12 months when the original
purchaser purchases the product, and the warranty is limited to manufacturing
defects.
support@soundpeatsaudio.com
www.soundpeatsaudio.com
Please scan the QR code to view the detailed version of the manual in PDF format
https://soundpeatsaudio.com/downloads/
FCC STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause
undesired operation.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>