Electrolux EYE01516WE Storage Electric Water Heater User Manual

June 26, 2024
Electrolux

Electrolux - logo EYE01516WE
**EYE03016WE

Storage Electric Water Heater
USER MANUAL
Nomor MKG : IMKG.629.03.2024**

SECURITY CHARACTERISTICS

The max inlet pressure is 0.8MPa.

  • Following warming sentences:
    If the supply cord is damaged. it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.

  • The pressure-relief device is to be operated regularly to remove lime deposits and to verify than is not blocked.

  • CAUTION: In order to avoid a hazard due to inadvertent resetting of the thermal cut-out, this appliance must be not supplied through an external switching device, such as a timer, or connected to a circuit that is regularly switched on and off by the utility.

  • This appliance can be used by children aged from 8 years and above and persons with reduced physic sensory or mental capabilities or lack of experience and knowledge if they have been given supervision instruction concerning use of the appliance in a sate way and understand the hazards involved. children shall not play with the appliance, cleaning and users maintenance shall not made by children without supervision,

  • This electrical water heater must be installed with a mono-directional safety valve at the inlet pipe(blue indicator) when the tank’s pressure is over 0.8 MPa, this will automatically active the safety valve, water will exit at the drain pipe outlet(Diagram1). In any condition, this outlet must not be blocked. If there is a need to empty the waterin the tank, first, close the mains water. Remove the fixed screw nail on the safety valve. lift up the plastic handle (see diagram 2) to let the water flow out naturally.

Electrolux EYE01516WE Storage Electric Water Heater -
diagram

THE OPERATING PROCEDURES

  • Check all the piping connection for leakage before turning on the electric power of the heater.

  • Make sure that the tank is fully filled up with water, otherwise it will cause the heating elements to be damaged.

  • Turn on the mains electrical power supply and then adjust the temperature knob clockwise for higher temperature and anti-clockwise for lower temperature.

  • The water heater needs to be turn on for a certain period of time to reach the acceptable temperature.

  • During the heating process, it’s normal to see a slight drip at the safety valve.
    Please do not cover up the safety valve outlet hole.

  • Connect safety valve outlet hole to a discharge pipe. Water may drip from the discharge pipe of the safety valve, therefore this pipe must be exposed to the atmosphere.

  • The safety valve is fo be operated regularly (preferably at least every six months) to remove lime deposit and to ensure that it is not blocked.

THE PRODUCT FEATURES

  • Unique Profile
  • Sapphire golden silicon tank which is rust-proof, erosion-proof and with higher efficiency and having a longer life span.

TECHNICAL REFERENCE DATA

Rated Volume 15L, 30L
Rated Voltage 220V˜
30L 500 W
Rated Pressure 0.8MPa
Rated Water Temperature 75°C
Water-proof Degree IPX4                                 Structure Mode

Hermeticollyclosed typed water storage style

PRODUCT STRUCTURE

INSTALLATION INSTRUCTIONS

  • The installation for electrical and plumbing work must be carried out by qualified personnel, according to the installation instructions and in compliance to the local authority regulations
  • Unit has to be installed as near as possible to the service points, in order to reduce heat loss along the pipes. To facilitate maintenance, allow a distance of 50cm for easy access to the electrical parts.
  • This electrical water heater should be mounted on a solid cement wall, preferably where it is close fo the power source’s sockets and water source.
  • Please use our company’s fitted accessories to mount this electric water heater.
  • Before determining the bolt hole’s position, you should ensure that the heater is more than 200mm from the ground or ceiling board. This will leave space for maintenance when necessary.
  • Assembling method: After selecting the proper fixing positions, use the inflating bolt to secure the hanging board firmly, then hook the electric water heater. (Diagram 4)

Electrolux EYE01516WE Storage Electric Water Heater -
diagram2

Electrolux EYE01516WE Storage Electric Water Heater -
diagram3

PIPE CONNECTION

  • All piping parts are BSP ½”. Wind some white tape at the thread sector of the inlet pipe (marked blue).
  • Fix the safety valve to the inlet pipe and then connect it to the cold water pipe of the mains.
  • Install a water drainpipe to the safety valve to drain away water discharge. (drain pipe joint outlet — diagram 5).
  • Install the drainpipe in a continuously downward direction and in a frost free environment.
  • Connect the hot water pipe (marked red) to the outlet pipe.
  • Do not over-tighten the safety valve and all pipes joint as it may cause damage to the joints.
  • Make sure all pipes are clean before installing the taps and showers.

Electrolux EYE01516WE Storage Electric Water Heater
-pipe

MAINTENANCE

  • All maintenance operation must be carried out by a qualified personnel.
  • Before contacting the customer service, make sure the suspected failure is not caused by a temporary lack of water.
  • To discharge the water completely from the tank, remove the safety valve from the water heater. Before removing the valve, the power of the heater need to be switched off for the tank to cool down (outlet connection must also bedisconnected)

ELECTRICAL CONNECTION

  • The electrical connection must be done by a qualified electrician.
  • The electrical supply is connected directly to the connector provided with the earth connection. The ground wire must be green/yellow in colour and attached to the terminal marked by the symbol.
  • The heater must be connected to the electricity supply that out of reach from the person using the shower.
  • All wiring must conform to localrequirements. If in doubt, please consult a qualified electrician.
    Note: All plumbing connections must be completed before making the electrical connections. Fill the tank with water and turn on the tap to let the water exiting out from the tank until all the air has been expelled out. Electricity on after water tank full of water.
    Note: Do not use multi-plug adapters and extension cable.

PACKING LIST

No. Name Unit(piece)
1 Storage Electric Water heater 1
2 User Manual 1
3 Inflation Bolt 2
4 Safety Valve 1
5 Hanging Board 1
6 Drain Pipe 1

WIRING DIAGRAM

TROUBLESHOOTING GUIDE

Symptom Cause Solution

Indicator light does not
light up.| 1. The power source not connected or badly connected.
2. Indicator damaged.
3. The overheating sensor activated.| Get the professional technician to check the electrical wiring and
indicators.
Water Temperature not
warm enough.| 1. The element is defective
2. Temperature controller malfunction.
3. No power to water heater.| 1- Call customer service to Replace the element
2. Call customer service for repair
3. Check power supply.
No water from the warm
water tap.| 1. Main water valve not turn on.| 1. Turn on the main water valve.
Water leakage| 1. Leaking from plumbingconnection.
2. Leaking at gasket| 1. Tighten the connection.
2. Tighten the element or replace the gasket.
Electrical mains tripped| 1. Element short circuit.| 1. Replace element.

Diimpor oleh :
PT. Electrolux Indonesia
Electrolux Building
Jalan Tanah Abang Il Nomor 42,
Desal Kelurahan Petojo Selatan,
Kec. Gambir, Kota Adm. Jakarta Pusat,
Provinsi DKI Jakarta, Kode Pos: 10160Electrolux - logo

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals