DURATECH DVP050 Vision Pro Moonlight Instruction Manual

June 6, 2024
DURATECH

DURATECH DVP050 Vision Pro Moonlight

Technical specifications

DURATECH DVP050 Vision Pro Moonlight Fig01

(*) Propulsion systems remains a tolerance of +/- 10% on luminous flux measurements @ 25°C ; 12VAC

For operation only with a safety isolation transformer

  • Minimum input voltage: (at lamp terminals) 10 VAC 50 Hz
  • Nominal input voltage: (at lamp terminals) 12 VAC 50 Hz
  • Maximum input voltage: (at lamp terminals) 14 VAC 50 Hz

IEC Protection Class III Operation on DC voltages is NOT allowed

  • Maximum water temperature: +40°C Lamps have to be keptout of ice zones
  • Ingress protection rate: IP68 measured at 3m max depth = 3m

Remarks

Water conditions Prevent damage to your pool lamps and wires due to unstable water conditions. Your local government may have enacted guidelines for your pool water conditions to apply by. If not we strongly advise the following parameter specifications to be applied:

  • pH level 6,8 – 7,6
  • Free Chlorine max. 3ppm
  • Combined chlorine max. 1 ppm
  • Water temperature max +40°C and lamps need to be kept out of ice zones

Always adhere to the instructions provided by your chemical brand/supplier for the correct use and application of pool chemicals. Salt water pools, or pools fitted with a salt water chlorine generator contain salt in the pool water. Salt is a corrosive material. Overdosage and/or consistent levels of salt increase the possibility of deterioration of your pool lamps and cables. As a rule of thumb, a concentration of 35gr/l salt can be accepted when pH values are between 7,2-7,4.
In any case, we urge proper use, care and maintenance of your installation, in order to mini-mize the effect of corrosion and deterioration. Please be aware that pool lamps and cables with defects caused due to abnormalities in the water condition are not covered by our factory warranty.

Installation/maintenance The luminaire is maintenance free If the luminaire needs to be replaced, it needs to be completely removed from the water

Always adhere to the instructions provided by your chemical brand/supplier for the correct use and application of pool chemicals. Salt water pools, or pools fitted with a salt water chlorine generator contain salt in the pool water. Salt is a corrosive material. Overdosage and/or consistent levels of salt increase the possibility of deterioration of your pool lamps and cables. As a rule of thumb, a concentration of 35gr/l salt can be accepted when pH values are between 7,2-7,4. In any case, we urge proper use, care and maintenance of your installation, in order to mini-mize the effect of corrosion and deterioration. Please be aware that pool lamps and cables with defects caused due to abnormalities in the water condition are not covered by our factory warranty.

Box contents

DURATECH DVP050 Vision Pro Moonlight Fig001

  • VISION Pro lamp (50mm)

  • 2m Cable 1mm2

  • Connection Kit (513-0480) fixnut with 1 washer for 1mm2 cable

  • Manual
    DVP100-RGBWDURATECH DVP050 Vision Pro Moonlight
Fig2

  • VISION Pro lamp (100mm)

  • 2m Cable 1,5mm2

  • Connection Kit (513-0230) fixnut with 3 silicone washers for 1,5mm2 cable

  • Manual

Installation instructions

Installing faceplate

DURATECH DVP050 Vision Pro Moonlight Fig03

Installing connector

DURATECH DVP050 Vision Pro Moonlight Fig04

Connector installation

DURATECH DVP050 Vision Pro Moonlight Fig5 DURATECH DVP050 Vision Pro Moonlight Fig6

Installation specialties

DVP050 & PZA-WG For installations with DVP050 & PZA-WG-S or PZA-WG-G: Please make sure to only use 1 silicone washer for the Fix nut

DURATECH DVP050 Vision Pro Moonlight Fig7

DVP050 Removal tool When DVP050 needs to be removed from the PZA-WG wall conduits, a special tool is needed (513-0491)*

  1.  Insert the tool over the lamp, straight into the wall conduit
  2. Twist the tool counter clockwise the lamp should be snapped into the 3 hooks of the tool
  3. Pull the lamp straight out of the wall conduit

Wiring instructions Setup 1 For new installations Each lamp is connected to the transformer by a separate cable

2m cable included in lamp package Separate cable ( not included ) Always use a toroïdal transformer

SELECT CABLE SECTION & MAXIMUM LENGTH

LAMP TYPE 1,5mm2 2,5mm2 4,0mm2 6,0mm2 10mm2 VA TRANSFORMER (12VAC)*

DVP050-RGBW

|

30m

|

50m

|

80m

|

120m

|

200m

| |

33 VA

DVP100-RGBW

|

8m

|

13m

|

22m

|

30m

|

55m

| |

85 VA

| | | | | | |

STABLE OPERATION OF THE POOL LIGHTS IS ONLY GUARANTEED WHEN THE INSTALLED CABLE CROSS SECTION MATCHES OR EXCEEDS THE ADVISED VALUES IN THE ABOVE TABLE

  • The transformer VA rating must be greater or equal to the sum of VA ratings of all connected lamps. These cable lenghts are calculated with worst case voltage drops in the electrical wiring.

Wiring instructions Setup 2 For existing or other installations All lamps are connected to the transformer via 1 cable

2m cable included in lamp package Separate cable ( not included ) Always use a toroïdal transformer

SELECT CABLE SECTION & MAXIMUM LENGTH

| ****

1

| ****

50m

| ****

80m

| ****

120m

| ****

200m

| | ****

33

---|---|---|---|---|---|---|---
DVP050-RGBW| 2

3

| 25m

17m

| 40m

27m

| 60m

40m

| 100m

67m

| 66

99

| 4| 13m| 20m| 30m| 50m| 132
| ****

1

| ****

13m

| ****

22m

| ****

30m

| ****

55m

| | ****

85

DVP100-RGBW| 2

3

| 7m 4m| 11m 7m| 15m 10m| 28m 18m| 170

255

| 4| 3m| 6m| 8m| 14m| 340

Wiring remarks

For installations with LINK Controller or LINK Master Third party equipment such as frequency inverters and electric motors can generate excessive noise on the 230VAC / 400VAC power line.
This noise might be injected into the adjacent 12VAC power line and disturb the power line communication towards the VISION Pro RGBW lights. To prevent this, please take care of the following:  Keep 230VAC / 400VAC power line cables at least 50cm separated over their full length from the 12VAC power line towards any RGB lights Do not mix 12VAC and 230VAC / 400VAC power line cables into the same cable  trays

DURATECH DVP050 Vision Pro Moonlight Fig10

(**) Do not mix 12VAC and 230VAC / 400VAC power line cables into the same cable trays

Synchronizing

With LinkTouch

  • LINK Controller (PLP-REM or PLP-REM-350)*
  • LINK Master (DLM450 or DLM600)

First make sure the LinkTouch is paired (see manual LinkTouch) Turn the lamps on and spin the color wheel on the LinkTouch until the lamps react. If the lamps do not react, turn them off and back on untill they react to the color wheel. As soon as the lamps follow the color wheel: wait 1 minute. The lamps are now synced.

With Transmitter LINK Controller (PLP-REM or PLP-REM-350)* Turn the lamps on en push the UP button 10 times. Wait for 5 seconds, then turn the lamps off. Repeat this process until the lamps react to the remote. As soon as the lamps follow the remote: wait 1 minute. The lamps are now synced.

Manual synchronization (without DURALINK control products)

  1.  Switch ON the 12 VAC line voltage and make sure that all lamps light up.
  2. Switch OFF the 12 VAC line voltage and wait for at least 20 sec (max 60 sec)
  3. Switch ON and switch OFF (max 3 sec ON and max 3 sec OFF)
  4. Switch ON and switch OFF (max 3 sec ON and max 3 sec OFF)
  5. Switch ON
  6. The lamps should now all be on color program 6: Blue

*PLP-REM or PLP-REM-350 need to have firmware V6.7 (29-07-20) or newer

Color programs

  1. DEEP BLUE SEA Saturated blue
  2. DAYLIGHT BLUE SUNSET Light blueLight blue
  3. LOVE IS IN THE AIR Slow animation orange-red
  4. FOREST SPRING Red
  5. THINK PINK Green
  6. SUNSHINE’ Pink
  7. JUNGLE BEACH Slow animation blue & green tints
  8. VOODOO Slow animation red & purple tints
  9. DISCO Fast animation lila-pink-peach-yellow-green blue
  10. PARTY Fast animation blue-green-red-pink-yellow-green
  11. WARM WHITE 3000K
  12. NEUTRAL WHITE 6000K
  13. SUN WHITE 10.500K

Troubleshooting

PROBLEM

  • The pool light is flickering

  • Several pool lights in the pool show different color programs

  • The lamp is flashing red
    SOLUTION

  •  Switch the lamps ON and select Cold white color program

  • Remove the lamp from the water, unscrew the fix nut, pull back the gasket and the black cable jacket, so you can reach the brass contacts inside the connector block
    (do not remove the connector block)

  • Measure the voltage at the lamp terminals (while the lamp is still ON)

  • The voltage at the lamp should be at least 10VAC 50Hz. If the measured line voltage is below 10VAC:

    •  Check the output voltage at the transformator terminals. This voltage should be between 12VAC and 14VAC. Verify that the used transformator VA rating is sufficient for powering all connected lamps
    • If the transformator output voltage is ok, then install a thicker cable between the transformator and the lamp.(wiring instructions p. 14-19)
  • Make sure that all lamps are connected to the same 12VAC power line. Execute the synchronization as explained on p.20

  • The lamp is exposed to an overvoltage. Consult an electrician to verify the installation and to make sure the voltage at the lamp side is below 14VAC.

Declaraction of Conformity Declarations of conformity covering this product are available for download from the House of Duratech website: www.duratech.be

DURATECH DVP050 Vision Pro Moonlight Fig11

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals