HiBOOST F12G-5S-IoT Cell Phone Booster User Manual

DOST Boost Your Bars
User Manual
F12G-5S-IoT F08G-5S-IoT

NOTE: This manual contains important safety and operating information. Please read and follow the instructions in this manual, failure to do so could be hazardous and result in damage to your cellular booster.

Package Content

Product Image| |
---|---|---
Product Name| Mini| Zoom
Model Number| FOBG-5S-IoT| F12G-5S-IoT
Coverage size| 500-2,000 Sq. Ft.| 800-3000 Sq. Ft.
Indoor Cable| 30 Ft. Low-Loss| HiBoost 200 Cable
Outdoor Cable| 30 Ft. Low-Loss HiBoost 200 Cable| 50 Ft. Low-Loss HiBoost 200 Cable
Indoor Antenna| Indoor Wide-Band| Directional Panel Antenna
Outdoor Antenna| Outdoor Wide-Band| Directional Antenna

Warning: Un-authorized antennas, cables, and/or coupling devices are prohibited by new FCC rules. Please contact FCC for details: 1 (888)-CALL-FCC

Introduction

Thanks again for purchasing a HiBoost cell phone signal booster. Our cell phone boosters are precision-engineered products that improve cellular reception inside of homes and office by amplifying incoming and outgoing cellular signal.
HiBoost’s exclusive cloud-based Signal Supervisor mobile application allow users to monitor the live status of HiBoost cell phone signal boosters remotely from a mobile device anywhere at any time.
If there are any issues while installing a HiBoost cell phone signal booster, please contact the HiBoost technical support team through the following options:

24/7 Online Support: Create a ticket or chat via Signal Supervisor App
Phone: 972-870-5666 (M-F from 9 am – 5 pm)
Email: support@hiboostusa.com
Website: www.hiboost.com

How Signal Boosters Work

Pre-Installation Instructions

The cell phone booster and the antennas must be strategically placed in order to perform and provide maximum coverage.
The HiBoost Signal Supervisor app will allow users to communicate to the signal booster via Bluetooth or WiFi. Once registered, the user can remotely monitor the signal booster’s performance.
Note: Signal Supervisor enabled boosters must have access to a Bluetooth enabled device in order to connect to the booster.

Professional Installation Tips:

• For a fast and optimized installation, it is strongly recommended that users install HiBoost products using the Signal Supervisor mobile application
• Completely read the user manual and gather all necessary tools, material and accessories before installing the booster
• A “soft installation” is recommended before permanently mounting any equipment – this technique will simplify the installation process by allowing users to identify any potential installation issues beforehand
• The Signal Supervisor App integrates a tool that will help users locate the best location for the outdoor antenna – ensure that there is at least 20 ft of vertical separation between both antennas
• It is important to have a strong and stable WiFi connection to the booster

Installation Signal Supervisor App

Before installing the Signal Supervisor App, please have the booster unit that is powered on and nearby.
Note: Turn on the Bluetooth feature enabled before attempting to register the booster to the mobile device.

Step 1: Download the Signal Supervisor App

• The application is available for download through Apple’s App Store or Google Play

Step 2: Create a New Account and Log-in

• Launch the app on your mobile device
• Select the HiBoost Server
• Log-in with an existing account create a new one

Step 3: Register the Booster by adding a device on the home menu Go to My Devices > Add a Device
Step 4: Follow the step-by-step Quick Installation Guide after registering the booster.
You can also access the guide by following:

Go to My Devices > Select the Booster > Device Details > Quick Install Guide
Note: Bluetooth connections are limited to a range of only 30 feet. If there are any issues installing the booster, please contact our technical support
team via the Online Support Chat.

Installation – Manual Method

Before beginning the installation, it is important that users survey and plan the layout of the cell phone signal booster system. Please review the following instructions before attempting to install this system.
In this set up, the user will need to use the outdoor antenna to find the strongest source of nearby cellular signal (generally in the direction of the nearest cell phone tower). This will optimize the system by helping user install the booster and antennas in the best position and direction.

A. Finding the Strongest Outdoor Signal
B. Install the Booster
C. Finalize the Installation

Part A) Outdoor Antenna Installation
There is not an antenna mast included in this kit. If you have question about how to install outdoor antenna, please call our support team at 972-870-5666. Below are installation instructions on how to install the mounting bracket. please follow the steps below to install the outdoor antenna with the mounting hardware included in the kit.

Part B) Indoor Antenna Installation
While determining where to install the indoor panel antenna, please ensure that there is at least 20 ft of vertical separation between the outdoor and indoor antenna. To avoid any oscillation issues, it is recommended that the outdoor antenna is pointed away from the indoor antenna.
The panel antenna included in this kit will be mounted to the wall. It has a coverage area that is a sector with a tilted angle. The signal is amplified
outwards from the front of the indoor antenna at a horizontal angel of 80-degrees. The height between the floor and the indoor antenna can vary.

Follow the steps below to install the indoor antenna.

1. Connect the indoor antenna to the booster using the coaxial cable.
2. Push the cable firmly into the jack on both the antenna and the booster, then turn the connector sleeve clockwise until the connectors are tight.
3. Find a location to mount the indoor panel antenna and permanently mount the indoor antenna panel antenna with the hardware provided in the kit.
   Note: It is important that the indoor and outdoor antennas are pointed away from each other.
   The outdoor signal strength will affect performance. It is important that users install the outdoor antenna in the right position on a mast that is mounted outside from the roof, balcony or ground.

It may help to visit an online resource such as www.cellmapper.net, www.cellrecption.com or www.antennasearch.com

1. Once the best location is located, use the hardware provided in the kit to mount the outdoor antenna on a mast pointing towards the nearest cell phone tower.
2. Connect the outdoor antenna transmission cable to the coaxial cable provided in the kit, then connect the coaxial cable to the outdoor port on the
   booster.

Note:

• It is easier to optimize the outdoor antenna installation using the Signal Supervisor app since it can determine real-time signal measurements using the outdoor antenna and signal booster.
• Find the best location for the outdoor antenna by using a cell phone to monitor the number of signal bars being received while slowly moving around to different locations.
• It is recommended that users perform multiple tests while moving around to different locations- refresh the signal bar readings by turning off and on airplane mode on the cell phone.
• It is important to gain height above nearby obstructions (such as trees, buildings, etc.) while mounting the outdoor antenna on mast.

Part C) Finalize the Booster Installation
Finalize the booster installation by following the steps below:

1. Users can mount or place the signal booster in a dry and cool area that is easily accessible for maintenance as below (it should be located near a power outlet).
   Booster Installation diagram for HiBooster Mini and Zoom:

2. Loosely run the coaxial cable from the indoor and outdoor antenna to the signal booster and secure all connections in the correct port
   Professional tips
   • Be careful while routing and bending cable – protect the connector by wrapping and securing a towel around the end of the cable
   • Keep horizontal cables straight and secure with zip-ties every 3-5 feet
   • Keep vertical cables straight and secure with zip-ties every 6-8 feet
   • Avoid water damage by using the waterproof tape provided in the kit on the connector attached to the outdoor antenna transmission cable
   • Be careful and avoid damaging the pins in the center of the connectors while attaching cables

3. Carefully plug in the power supply to the booster port marked ‘DC 12V’
   Note: For safety purposes, it is recommended to use a 1,000 Joule surge protector between the booster’s power supply and AC power outlet

4. Check to see if all LED indicators are green and that all the following parameters are met:
   √ There are at least 20 feet worth of vertical separation in between the indoor and outdoor antennas
   √ The front of the outdoor antenna is NOT facing towards the front of the indoor antenna
   √ All coaxial cable connections to the antennas and booster are properly connected

Troubleshooting Guide

Eliminate ISO LED Indicator Quick Flashing Blue, Quick Flashing Red problems:

1. Adjust the outdoor antenna direction, keep it away from the indoor antenna restart the booster
2. Increase the vertical or horizontal distance between the outdoor antenna and the indoor antenna – restart booster
3. Use metal or wall barriers to increase the isolation between the indoor and outdoor antennas – restart booster
4. Change the indoor antenna type to an antenna with a more directional antenna pattern – orient the indoor antenna and the outdoor antenna so they are not pointing at each other

The ISO issues are solved when the ISO LED is “Blue” or “Slow Flashing Blue”.
If the signal has not been improved, please check below:

• A weak downlink signal leads to the low output signal level – change the direction or position of the outdoor antenna (check downlink gain levels using the Signal Supervisor app)
• Try replacing the outdoor antenna with a higher gain antenna to increase the amount of signal being received
• Check to see if it is necessary to adjust the position of the indoor antenna barriers such as walls can block the signal indoors
• Ensure that there are at least 20 feet of vertical separation between the indoor and outdoor antenna
• Ensure that the indoor and outdoor antennas are facing away from each other
• Check the booster to make sure the output power is maximized – the user may need to replace the booster with a more powerful one if the amount of outdoor signal available is limited

Other Troubleshooting Issues You may reference the chart below to identify the current status of your booster:

LED STATUS INDICATORS

signal
Bluetooth LED| slow flashing blue| bluetooth disconnected
quick flashing blue| bluetooth connected
Wi-A LED| solid blue| wifi disconnected
slow flashing blue| wifi connected

If you have any issues installing your HiBoost Booster, please contact our technical support team.

Online Support : Create a ticket or chat via Signal Supervisor App
Phone: 972-870-5666 (M-F from 9 am – 5 pm)
Email: support@hiboostusa.com
Website: www.hiboost.com

Outdoor Antenna

Indoor Antenna

Frequency Range(MHz)| Panel| Omni|
---|---|---|---
antenna(dBi)| antenna(dBi)| Cable Loss(dB)
728-746| 5| 3| 5.
746-757(for FCC)| 5| 3| 5.
746-756(for IC)| 5| 3| 5.
869-894| 5| 3| 5.
1930-1955| 7| 3| 8.
2110-2155| 7| 3| 8.

FCC and ISEDC Statements

FCC RF EXPOSURE STATEMENT
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End-users must follow the specific operating instruction for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment should be installed and operated with minimum distance 20cm between the radiator& your body.

ISEDC RF EXPOSURE STATEMENT
The device is compliance with RF exposure limits. The minimum distance from body to use the device is 20 CM.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Re-orient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
• Consult the dealer or an experienced radio/TV technician for help

Changes or modifications not expressly approved by HiBoost could void the user’s authority to operate the equipment. For a complete list of antennas and cables approved for use with these boosters see Authorized Kitting Options

FCC 27.SO(d)(4) Statement:
Fixed, mobile, and portable (handheld) stations operating in the 1710-1755 MHz band are limited to 1-watt EIRP. Fixed stations operating in the 1710-1755 MHz band are limited to a maximum antenna height of 10 meters above ground.
FURTHER INFORMATION ON SIGNAL BOOSTER END-USE REGISTRATION
The following links are the currently active contacts for booster registration with U.S. wireless providers:
https://www.uscellular.com/uscellular/support/fcc-booster-registration.jsp
https://www.sprint.com/legal/fcc_boosters.html
https://ww.verizonwireless.com/solutions-and-services/accessories/register–

signal-booster/ https://support.t-mobile.com/docs/DOC-9827 https://securec45.securewebsession.com/attsignalbooster.com/

ISEDC Statement:
This device complies with innovation, Science, and Economic Development Canada licence RSS standard(s). Operation is subject to the following two conditions:

1. this device may not cause interference, and
2. this device must accept any interference, including interference that may cause undesired operation of the device.

This device complies with Innovation, Science and Economic Development Canada ICES-003 Compliance Label: CAN ICES-3 (B)/ NMB-3(8). Le psent appareil est conforme Innovation, science et developpement onomique Canada ICES-003 Etiquette de conformitCAN ICES-3 (B) / NMB-3

(B). Please follow the link to access the CPC-2-1-05: http://www.ic.gc.ca/eic/site/smt-gst.nsf/eng/sf08942.html

This is a CONSUMER device.

BEFORE USE, you MUST REGISTER THIS DEVICE with your wireless provider and have your provider’s consent. Most wireless providers consent to the use of signal boosters. Some providers may not consent to the use of this device on their network.

If you are unsure, contact your provider.

In Canada, BEFORE USE , you must meet all requirements set out in ISED CPC-2-1-05.
You MUST operate this device with approved antennas and cables as specified by the manufacturer. Antennas MUST be installed least 20 cm (8 inches) from (i.e., MUST NOT be installed within 20 cm of) any person.

You MUST cease operating this device immediately if requested by the FCC (or  ISED in Canada) or a licensed wireless service provider.
WARNING. E911 location information may not be provided or may be inaccurate for calls served by using this device.
This device may be operated ONLY in a fixed location (i.e., may operate in a fixed location only) for in-building use.

Technical Specifications

Specifications working Band : Band12(17)/Band13/Band5/Band25(2)/Band4
UL Frequency Range(MHz) : 698-716/776-787(for FCC)/824-849/1850-1915/1710-1755 698-716/777-787(for IC)/824-849/1850-1915/1710-1755
DL Frequency Range(MHz) : 728-746/746-757(for FCC)/869-894/1930-1995/2110-2155 728-746/746-756(for IC)/869-894/1930-1995/2110-2155
Supported Standards : CDMA,WCDMA,GSM,EDGE,HSPA+,EVDO,LTE and all cellular standards
Max.Gain : 70dB
I/O Port : N-Female
Impedance : 50 ohm
Environment Conditions : Ip40
Dimensions : 7.64.53 in/19311576mm
Weight : 3.3Ibs/1.5kg
Power Supply : Input AC 100~240V,50/60Hz,Output DC 12V/3A

Return and Warranty Policies

30-Day Money-Back Guarantee:
If for any reason the performance of any product is not acceptable, the product may be returned to the reseller within 30-days with proof of purchase. Please contact the HiBoost customer support.

3-Year Warranty:
HiBoost signal boosters and kits are warranted for 3 years. HiBoost will repair or replace the unit and will cover the cost of delivery for consumers located within the continental U.S and Canada.

Customers can choose to return the signal boosters and kits directly to the manufacturer at the purchaser’s expense with a dated proof of purchase and a Returned Material Authorization (RMA) number supplied by HiBoost. RMA numbers may be obtained by contacting customer support at 972-870- 5666 or support@hiboostusa.com

This warranty does not apply to any signal boosters or kits determined by HiBoost to have been subjected to tampering, misuse, abuse, neglect, or mishandling that alters or damages physical or electronic properties.

HiBoost is not liable for any Signal Supervisor application network connectivity issues. The cell phone signal booster relies on a strong, continuous, and reliable connection to the internet in order to communicate with the cell phone application. For all Signal Supervisor Application-related issues, please check your network strength and call our technical support.

All HiBoost products that are packaged with other HiBoost accessory products are intended for resale and used as a single integrated system. Such product kits are required to be sold to the end-users or subsequent reseller as packaged.

SAFETY AND WARNINGS

• Turn AC power OFF at the main circuit breaker before working on any electrical connections.
• All AC power wiring and coaxial cable wiring must conform to local or national codes.
• The AC rated input power must be within 10% of the voltage requirements of the device.
• When grounding the system, a solid copper conductor no smaller than 8 AWG should be used.
• DO NOT connect a ground wire to a gas supply line.
• DO NOT open the booster. Touching internal parts could cause injury or damage. This will void the waranty.

HiBoost
6210 N Beltline Rd. #110
Irving, TX 75063
972-870-5666
support@hiboostusa.com
www.hiboost.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>