Home-it 17887 Wireless Door Clock User Manual
- June 6, 2024
- Home-it
Table of Contents
User manual
61.023
Introduction
Thank you for choosing the wireless doorbell. Please read this instruction carefully before assembling and using the product. Keep your owner’s manual for future reference.
Features
- Wireless, no cabling needed
- Operating range up to 150 meter
- 58 selectable melodies
- 4 volume levels
- Transmitter IP-classlP44
- Self-learning code function
- Music and indicator lighting with 4 modes: ringing + flashing light, ringing onIy, flashing light onIy, ringing + constant light
- Memory function: when power off, the melody and volume settings are kept the same
Safety instructions
- Please do not open PCB or repair it without professional guidance in order to avoid the breakdown of components.
- The operating range may be affected by environmental factors and nearby interference sources.
- Proper use will prolong the life span of wireless doorbells effectively.
Specifications
Rated voltage: 110-240 VAC, 50/60 Hz
Volume: 25-85 dB
Working frequency: 433 MHz
Receiver standby power: <0.5W
Transmitter battery: 1 x CR2032 (3V) battery (included)
Transmitter operation power: <10mW
Overview
Installation
- Tear up one side of the double-sided adhesive sticker and paste it to the underside of the Transmitter.
- Tear the other side of the double-sided adhesive sticker.
- Choose a good place and paste it up, then pressed a little to ensure the transmitter is solid.
- Aug the doorbell into a regular socket within the operating range.
- Press the button on the receiver of “Music”&“Volume” to choose to preferred music and suitable volume.
- Press the “Music and light mode” button to choose the preferred mode, the light will light when choosing the mode “Ringing+ Light all the time”. For other modes, you should press the transmitter to prove.
Remarks
Please tear up the transmitter battery insulation sheet before use.
Self-learning code function operation:
Products already have been paired in Factory. If you need to replace the
transmitter, increase or decrease the doorbell quantity, please follow steps
below:
-
Learn code pairing:
Pressing and holding the “music and light mode button” for about 3 seconds, the bell will ring (bird call). Press the transmitter 2 times within 30 seconds. If the doorbell rings, the pairing is successful If the doorbell does not ring, please repeat the above operation, until the pairing is successful. For matching multiple transmitters, please repeat the above operation. -
Delete pairing:
Press and hold the “music and light mode button” for about 10 seconds until the bell rings two times. All pairing codes will be deleted completely.
Disposal
Do not dispose of this product as unsorted municipal waste. Collection of such
waste separately for special treatment is necessary.
This product must not be disposed of together with domestic waste.
This product has to be disposed at an authorized place for recycling of
electrical and electronic appliances.
By collecting and recycling waste, you help save natural resources, and make
sure the product is disposed of in an environmentally friendly and healthy
way.
SERVICE AND REPAIR
We offer a warranty on our products in accordance with the legislation in
effect in each country. (Proof of purchase must be presented/submitted.)
We provide service and repair free of charge during the warranty period in
accordance with the Danish Sale of Goods Act and on the following terms.
1. The fault is a design or material fault (this does not include normal wear
and tear and misuse).
2. Repair has not been attempted by anyone other than Millarco’s approved
service workshops
3. No non-original parts have been used on the product
Free service covers the replacement of defective parts and man-hours.
The product is to be returned to the place of purchase, and the store will
send it in for service. We do not accept products for repair or warranty
obligations directly from the customer.
Should technical questions arise, you are naturally welcome to contact our
service workshop:
Millarco International A/S, Rokhøj 26, DK – 8520 Lystrup
Service phone: +45 8743 4233
E-mail: service@millarco.dk