mobvoi AI Mini Digital Voice Recorder User Manual

June 6, 2024
Mobvoi

Mobvoi Al Recorder
Manual

Package contents

Manual Quick guide

USB Type – C data wire

Device composition

Front side of AI recorder

Rear side of AI recorder

Operation instructions

Bluetooth pairing

Long press Bluetooth until green indicator flickers

  1. Power on, the start button is on in green, APP will detect device Bluetooth automatically for connection.
  2. If the device has been connected to a mobile phone Bluetooth, the device will have an automatic connection when detecting that Bluetooth is enabled.

Start/stop recording

  1. Power on, click “Record” and it will shake; recording is started when red indicator flickers.
  2. Click the “Record” key again to shake, the red indicator is off and the recording is stopped.

WiFi fast transfer

Turn on WiFi fast transfer to speed up the transfer of records into the mobile phone APP

  1. When Bluetooth is connected to the mobile phone, click WiFi button again, WiFi blue indicator is on, which means WiFi fast transfer is enabled.
  2. The APP will detect WiFi automatically for automatic connection.
  3. When APP is connected, enter the device’s folder for data synchronization.

Indicator status

Record key Red indicator flickers Recording in process
○ Red indicator is off Recording is completed Power on
WiFi on/off key Green indicator is on

Green indicator flickers

Green indicator is normally on

| Wait for Bluetooth connection
Bluetooth  connection
o Red indicator is on and then becomes off| Power off
Red indicator flickers| Low power

WiFi connection enabled

Blue indicator is on
Blue indicator flickers| WiFi connecting
Blue indicator is normally on| WiFi connected
OTA upgrading
Yellow indicator flickers
WiFi on/off key (charging)| Red light is on| Charging
Green indicator is normally on| Charging completes

Connect new device

Open mobile phone APP → Bluetooth setting, click “Unbind device” to connect the recorder to the new mobile phone. The mobile phone can also be connected to a new device.

Safety and precautions

Safety and Notice
Important safety message
Please handle the recorder with care to avoid damage, battery liquid leakage, overheating, fire, explosion, or personal injuries if it falls down, burns, be pierced, squeezed, dismantled, or exposed to high temperature or liquid, for it, contains high-sensitivity electronic components (including battery). Do not use it if the recorder is damaged.
Bluetooth®
Bluetooth®   word mark and trademark are owned by Bluetooth SIG, INC. Use of this mark by Shenzhen Tinno Technology Co. Ltd. is subject to the license. Other trademarks and trade names are owned by the respective owners.

Battery
Do not attempt to replace the recorder’s battery to avoid damage, overheating, or personal injury. The battery must be operated by the manufacturer or maintenance institute authorized by the manufacturer. [Warning] Do not put the recorder in a high-temperature environment, such as places with direct sunlight, open fire, heating, microwave oven, and oven. Do not put the recorder in water to avoid battery overheating.
USB connection wire and recorder
Avoid long-term contact between skin and plug when the USB connection wire is connected to the power supply; otherwise, discomfort or injury will occur. For example, do not sit or lean on the USB plug, nor put it under the carpet, pillow, or your body when the connection line is inserted into the power socket for charging. Please be careful if your perception of heat is affected. Please charge the recorder using the charger permitted by the manufacturer; otherwise, fire hazards, explosions, or scalds will occur. Do not touch any exposed metal of the USB connection wire when connecting the power supply to avoid electric shock. Make sure USB connection wire and recorder are put in dry places during charging and make sure USB connection wire and recorder are not immersed in water; otherwise, electric shock or short circuit will occur and further lead to fire hazards, explosion, and scald. Stop using the recorder immediately if it becomes hot; if the recorder becomes hot during charging, unplug the recorder and USB connection line from the power supply, contact the manufacturer’s after-sales personnel for solutions, in order to avoid scald or battery explosion.

Suffocation
Do not swallow or bite the recorder, but keep it inaccessible to children for it may lead to suffocation or other injuries of children.

Electronic device
Do not use the recorder where the electronic device is prohibited, for its radio wave may bring interference to other devices and lead to accidents and hazards. Do not use the recorder when you take a plane but follow the regulations of the airline, for it, may affect the flight system.
Interference of medical device
The electromagnetic wave may be emitted by some components and radio of the recorder. Besides, the recorder also contains magnets. Such electromagnetic waves and magnets may bring interference to the pacemaker, defibrillator, or other medical devices. Please follow the rules and turn off the recorder in medical places where the recorder is prohibited, or keep a safe distance between your recorder and the specific medical device. Please consult your physician and manufacturer of the medical device to acquire the operation information of a specific medical device if using the recorder along with the medical device. Please stop using the recorder immediately if it is suspected to affect your heart rate regulator, defibrillator, or other medical devices.

Skin stimulation
Please stop using the recorder immediately if there’s skin simulation when using the recorder. If skin simulation remains, it is suggested that you see a doctor and consult a professional doctor.

Electrostatic shock
Your body may encounter weak electrostatic discharge when using the recorder in places with dry areas due to the easy accumulation of static electricity. Please avoid using the recorder in extremely-dry places, or put the recorder onto the grounded and unpainted metal object to minimize the hazard of electrostatic discharge.
Ambient environment
It is recommended to use the recorder at a temperature [-5℃ -40℃ ] and store it at a temperature [0℃ -30℃ ]; Otherwise, the recorder may be damaged. Do not use the recorder in case of a thunderstorm to avoid possible damage. Do not use the recorder in humid, rainy, dusty, or oily places to avoid faults of internal circuits. Do not use or store the recorder in places that are close to gas stations, inflammable, or explosives. Do not immerse the recorder in liquid or expose it to pressurized fluid, such as water flow in the shower. Do not carry the recorder when you have other activities, such as showering or swimming, to avoid damaging it. The charging port can be corroded by the sweat or liquid in the charging USB. Make sure to clean the charging USB before you put the charging wire in the packaging box.

Certification Information
FCC ID:2AX5U-CXR-TNT

Hazardous Substances of Product

Name and content of hazardous substances in the product

Part Name Hazardous Substances
Lead (Pb) Mercury
(Hg) Cadmium
(Cd) Hexavalent

Chromium
(Cr(VI))| Polybromi-
noted
Biphenyls
(PBB)| Polybromi-
noted Diphenyl Ethers
(PBDE)
Components of printed
circuit board| X| 0| 0| 0| 0| 0
Plastic| 0| Q| 0| 0| 0| 0
Metal| X| 0| 0| 0| 0| 0
Battery| X| 0| 0| 0| 0| 0
Accessory| X| 0| 0| 0| 0| 0
This sheet is prepared as per SJ/11364.
0: Content of hazardous substance of this part in all homogen­eous materials is conforming to the limit requirements of GB/T 26572.
x:  Content of hazardous substance of this part in all homogeneous materials is nonconforming to the limit requirements of GB/T 26572.

The figure in this mark means the product enjoys a 10-year environmental- protection period under normal use conditions. The parts above may be excluded from the product due to the difference in the model. The actual configuration of the product sold should prevail.
Some internal/external components may have marks of environmental protection period according to the standard of China’s electronic industry SJ/T 11364 and relevant laws and regulations of China. The mark of use period on product and component may vary depending on the component and manufacturer. For any conflict or difference in the environmental-protection period, the ones on component should prevail.

Three-guarantee Voucher of Mobvoi AI Recorder

Warranty Service
For any non-artificial performance failure of the recorder under normal use conditions, the consumer of Mobvoi AI Recorder enjoys three-guarantee services as of the date of procurement.

  1. For any performance failure within 7 days after procurement, the consumer may return, exchange or repair the recorder.
  2. For any performance failure within 15 days after procurement, the consumer may exchange or repair the recorder.
  3. The recorder enjoys 1-year quality warranty as of the date of procurement.

Three-guarantee service applies if:
The recorder is not dismantled, repaired, maintained, or modified without permission;
The recorder is not running in an abnormal environment (such as a special environment with high magnetic fields, strong electric field,s or high humidity);
The recorder is damaged due to a violation against the user’s manual;
The recorder has collision, falling, and bending due to improper storage, faults, and major deformations due to liquid leakage in humid places.
The consumer should show the valid invoices and three-guarantee vouchers to enjoy the 3-guarantee policies.
Three-guarantee service does not apply and paid repairing is provided if:

  1. The recorder is damaged due to improper use, maintenance, and storage of the consumer;
  2. The recorder is damaged due to unauthorized dismantling;
  3. The consumer fails to show the three-guarantee voucher and valid invoice;
  4. The model of the product on a three-guarantee voucher is inconsistent or modified;
  5. The recorder is damaged by Force Majeure.

After-sales service does not apply in the following cases and the recorder has no quality problems:
The customer is unsatisfied with the recorder’s performance;
The customer is unsatisfied with the battery life, compatibility, color, appearance, and shape of the recorder’s battery;
The recorder has normal wear and aging;
The attached charging wire is damaged and it’s color and material have decayed.

Sales Records

Customer Name: Tel:
Address and Postcode:
E-mail:
Seller (seal): Procurement Date:
Tel:
Address and Postcode:
SN No:

FCC regulatory conformance:

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

  1. This device may not cause harmful interference.
  2. This device must accept any interference received, including interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help

NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s
authority to operate the equipment.

RF Exposure
The SAR limit of FCC is 1.6W/Kg for the body. The highest SAR value reported under this standard during product certification, when used against the body, is 0.243W/Kg.
Use 0mm away from the body.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals