Climax Technology ACGS-23 Acoustic Glass Break Detector Instruction Manual

Acoustic Glass Break Detector (ACGS-23)

The Glass Break Detector detects the high-frequency sound emitted by glass breakage and transmits a signal to notify the alarm system control panel when it is triggered.

Parts Identification

1. Green LED Indicator (Inside)
2. Red Indicator (Inside)
3. Microphone
4. Dip Switch
5. Battery Compartment
6. Learn / Test Button
   -Press the button once to send a learn-to-code.
7. Tamper Switch
   -The tamper switch is compressed against the back cover and protects the Detector from cover opening or removal from the mounting location
8. Breakaway Area The Breakaway Area has 2 knockouts where plastic is thinner for screw mounting. When the Detector is forcibly removed from the mounting location, the Break-Away area will detach and allow the tamper switch to be activated.

LED Indicator

• The LED indicators are inside the front cover and are only visible when activated.

• Red LED: The Red LED activates when:
  Tamper Switch is activated.
  Learn/Test button is pressed.
  Glass break detected under Test Mode, Low Battery, or Tamper open condition
  (The Red LED does not light up when glass break is detected during normal operation)

• Green LED
  The Green LED activates when a glass break is detected under Test mode.

Getting Started

1. Insert the battery to power on the device.
2. Put the Control Panel into learning mode, refer to panel manual for detail.
3. Press the Learn/Test button once to transmit learn code to the panel.
4. Refer to panel manual to complete learning process. 5 Refer to panel manual to complete the learning process.

Sensitivity Adjustment

The Glass Break Detector sensitivity can be adjusted using the two dip switches. Adjust the sensitivity to change detector range.

Test mode

Test mode is used to help check the Glass Break Detector’s detection distance. When the Learn/Test button is pressed, the Glass Break Detector will enter Test mode for 5 minutes. Pressing the button again during the 5-minute period will reset test mode time to 5 minutes.
During Test Mode, both Red and Green LEDs will light up when a glass break is detected.

Testing the Detector

The Detector should be tested to ensure it is able to detect glass breakage successfully. A FlexGuard FG-701 Glassbreak Simulator is required to test the detection function.

1. Press Learn/Test button once to put Detector into Test mode for 5 minutes.
2. Set the FlexGuard FG-701 to “FLEX” and “TEST” mode.
3. Put FG-701 at a desired testing location on the glass and point the speaker at the Detector. Close the window covering if it is present.
4. Strike the glass with a cushioned tool to create a glass striking sound. When FG-701 detects the glass striking sound, it will react by emitting a glass break sound.
5. The Detector will only be activated if it detects both glass striking and glass break sounds. When activated, both Green and Red LED will light up to indicate a glass break has been detected.

Supervision Function

When the Glass Break Detector is in normal operation, it will transmit a supervision signal regularly every 30~50 minutes.

Battery

The Glass Break Detector uses a 3V CR123A Lithium battery. The Glass Break Detector can detect low battery voltage. When the low battery voltage is detected, a low battery signal will be sent to the Control Panel along with regular signal transmissions for the Control Panel to display the status accordingly. When changing the battery, press the learn/test button a couple of times to discharge after removing the battery before inserting a new one.

Glass Thickness

Plated Glass: 2.4 to 6.4 mm (3/32 to 1/4″)
Tempered Glass: 2.4 to 6.4 mm (3/32 to 1/4″)
Wired Glass: 3.2 to 6.4 mm (1/8 to 1/4″)
Laminated Glass 3.2 to 6.4 mm (1/8″ to 1/4″)

Installation

The Glass Break Detector should be mounted on the ceiling or wall. There should be no obstacle between the Detector and the window protected. The Detector back cover has mounting knockouts which can be broken for screw mounting. Alternatively, you may also mount the detector with double side adhesive tape provided.

Mounting Location:

• Mount away from the sound source, such as speaker, air condition, or motor.
• Mount with as much distance from the window or door as possible to avoid external sound interference.

Screw Mounting

1. Breakthrough the knockouts on the back cover and use them as a template to mark the position on the wall/ceiling.
2. Drill holes at the marked location and screw the back cover onto the wall/ceiling, insert wall plug if needed.
3. Replace the Detector main body onto the back cover. Make sure the cover is properly closed and the device is fixed to the wall tightly.

Adhesive Tape Mounting

When using provided double side adhesive tape, make sure to install the detector on flat surface. Do not I install on uneven surfaces or locations with cracking paints.

1. Clean both the detector back cover and mounting location with a suitable degreaser.
2. Apply the double side adhesive tape to the back cover of the detector, then apply to the mounting location.

< NOTE>
**** When mounting with double side adhesive tape, the tamper protection for mounting location removal will be disabled. Protection from cover opening is still available.

Federal Communication Commission Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: To assure continued compliance, any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. (Example – use only shielded interface cables when connecting to computer or peripheral devices).

FCC Radiation Exposure Statement

This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body.

This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
The antennas used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co- located or operating in conjunction with any other antenna or transmitter.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>