Beacon Lighting 039264 Chrysler Bottle Glass Shade Installation Guide

Beacon Lighting 039264 Chrysler Bottle Glass Shade

Product Usage Instructions

• Ensure the luminaire is compatible with the Chrysler Bottle Glass Shade.
• Refer to the luminaire’s instruction manual for installation directions for the complete setup.
• Carefully follow the assembly and installation instructions provided in this manual.

Safety Tips

1. Before assembly or installation, ensure all components are in good condition.
2. Handle the glass shade with care to avoid breakage.
3. Make sure the installation area is suitable and can support the weight of the shade.

FAQ

• Q: Can I use the Chrysler Bottle Glass Shade with any luminaire?
• A: No, ensure compatibility with specified Chrysler Wall Brackets and Luminaires as mentioned in the manual for optimal performance.
• Q: Is the glass shade suitable for outdoor use?
• A: Due to the open base design, using this shade with specified luminaires may affect the IP44 rating, hence it is recommended for indoor use only.

CHRYSLER BOTTLE GLASS SHADE

• SKU# 039264, 039265

NOTE: This instruction manual is the installation directions for the shade only.
The luminaire is sold separately, refer to the instruction manual included with the luminaire for installation directions.
To ensure correct function and safety, please read and follow all instructions carefully before assembly, installation and use of this product. Please keep instructions for future reference.

Warranty

• This product is covered by a 12-months warranty valid for in-store replacement or refunds only.
• The warranty is from the date of purchase, not the date of installation.
• Please retain the proof of purchase for any warranty enquiries.
• The warranty will be void if there is any damage due to improper usage or modification to the product.
• Failure to comply with the instructions in this manual may increase the risk of damage or injury and will void the warranty.

Installation Requirements

• This installation instruction is for the shade only. No electrical wiring connection or disconnection is required for installation of the shade. The service of a licensed electrician is not required.

• The luminaire (sold separately) must be assembled and installed by a licensed electrician before installing this shade.

• The luminaire (sold separately) must not be used if the lampshade has been damaged or cracked. Replace the
  lampshade before using the luminaire ( sold separately).

• Check whether the product has been damaged during transport. Do not operate/install any product that appears damaged in any way. Return the complete product to the place of purchase for inspection, repair or replacement.

• Ensure power to the circuit you are working on has been switched OFF.

Luminaire Compatibility

• This shade is compatible with the following luminaires (sold separately):
• Chrysler Suspensions – SKU# 039210, 039211, 039212, 039213, 039214, 039215
• Chrysler DIY Batten Fix – SKU# 099149, 099150, 099151
• Chrysler Wall Brackets* – SKU# 039268, 039269, 039270, 039271
• Chrysler Luminaires* – SKU# 039237, 039238

NOTE: As this glass shade is open at the base, the above Chrysler Wall Brackets and Luminaires will no longer be IP44-rated when used in conjunction with this shade.

Installation Directions – Lamp Holder exposed above the Shade
NOTE: Ensure power to the luminaire (sold separately) you are working on has been switched OFF before commencing the installation.

1. Install the glass shade (E) onto the lamp holder cover (A – included with the luminaire, sold separately) and secure by tightening the 3 nuts (B – included with the luminaire, sold separately).
   NOTE: Do not overtighten the nuts (B) as this may crack and damage the glass shade.

2. Instal a globe (D – not included) into the lamp holder (C – included with the luminaire, sold separately). Do not exceed the maximum wattage rating.

3. After the installation, switch on the luminaire to test and enjoy your new lighting product.

Installation Instructions

Safety Tips

• Always ensure the power is OFF and the luminaire has cooled down before performing any maintenance, cleaning, changing the globe or making any adjustment to the luminaire or product.
• The luminaire (sold separately) must not be used if the lampshade has been cracked or damaged. Replace the lampshade before using the luminaire (sold separately).
• To avoid injury or damage to the luminaire or product, ensure that power leads and screws are secure before connecting the power.
• Select a suitable location away from liquids and hazards.
• To clean, wipe with a soft damp cloth. Do NOT soak or immerse the luminaire or product in water or other liquids.
• Ensure that the product does not come in contact with corrosive chemicals/solvents or abrasive cleaners etc.

Specifications

039213, 039214, 039215

Chrysler DIY Batten Fix – SKU# 099149, 099150, 099151

Chrysler Wall Brackets* – SKU# 039268, 039269, 039270, 039271

Chrysler Luminaires* – SKU# 039237, 039238

Shade Weight| 0.7kg
Shade Dimensions| H:208mm    Dia:185mm

NOTE: As this glass shade is open at the base, the above Chrysler Wall Brackets and Luminaires will no longer be IP44-rated when used in conjunction with this shade.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>