FERM BGM1020 Bench Grinder 250 W Instructions

FERM BGM1020 Bench Grinder 250 W Instructions

Thank you for buying this Ferm product.
By doing so you now have an excellent product,  delivered by one of Europe’s leading suppliers. All products delivered to you by Ferm are manufactured according to the highest standards of performance and safety. As part of our philosophy we also provide an excellent customer service, backed by our comprehensive warranty. We hope you will enjoy using this product for many years to come.

The numbers in the following text refer to the pictures.

Read the operating instructions carefully before using this device. Familiarize yourself with its functions and basic operation. Service the device as per the instructions to ensure that it always functions properly. The operating instructions and the accompanying documentation must be kept in the vicinity of the device.

**Contents

**

1. Machine data
   

2. Safety instructions
   

3. Installation
   

4. Operation
   

5. Maintenance

Machine data

Technical specifications

Voltage| 230 V
Frequency| 50 Hz
Power input| 180W S1, 250W S2
Rotational speed, not loaded| 2980/min
Duty time| S2 = 30 min
Grinding wheel dimensions| Ø 150×20 mm
Ø 150×40 mm
Spindle hole diameter| Ø 12.7 mm
Weight| 8.5 kg
Lpa (Sound pressure level)| 80.7+3 dB(A
Lwa (acoustic power)| 91.7+3 db(A

Load factor
A load factor of S2 = 30 min (intermittent periodic duty) means that you may operate the motor continuously at its nominal power level for no longer than the time stipulated on the specifications label (30 minutes ON period). If you fail to observe this time limit the motor will overheat. During the OFF period the motor will cool again to its starting temperature.

Vibration level
The vibration emission level stated in this instruction manual has been measured in accordance with a standardized test given in EN 62841; it may be used to compare one tool with another and as a preliminary assessment of exposure to vibration when using the tool for the applications mentioned.

• using the tool for different applications, or with different or poorly maintained accessories, may significantly increase the exposure level
• the times when the tool is switched off or when it is running but not actually doing the job, may significantly reduce the exposure level.

Protect yourself against the effects of vibration by maintaining the tool and its accessories, keeping your hands warm, and organizing your work patterns.

Contents of the package

1. 1 Bench grinder
2. 2 Sets spark guard bracket + spark guard
3. 1 Tool rest (right)
4. 1 Tool rest (left)
5. 1 Instruction manual
6. 1 Safety instructions
7. 1 Guarantee card

Check the machine, loose parts and accessories for transport damage.

Features

Fig. A

1. On/off switch
2. Tool rest (right)
3. Spark guard
4. Spark guard bracket
5. Screw
6. Tool rest (left)

Safety instructions

Explanation of symbols

Denotes risk of personal injury, loss of life or damage to the tool in case of non-observance of the instructions in this manual.

Indicates the presence of an electrical voltage.

Keep bystanders away.

Wear eye and ear protection.

Special safety instructions
When using the machine for the first time:

• Check the following:

  • Does the voltage rating of the bench grinder correspond to the power supply?
  • Is an earthed mains power socket available?
  • Are the power cord and plug in good condition (solid, without fraying or other damage)?

• Avoid the use of long extension cords. The extension cords you use must always be earthed.

• A grinding wheel is a brittle tool piece. The stone is not resistant to knocks.

• Always grind on the front edge of the grinding wheel, and never on the side of the grinding wheel. Never fit a cracked grinding wheel.
  Replace it immediately, as the high rotational speed could cause the stone to fly apart, causing a serious accident.

• Always wear safety glasses when grinding.

• Never grind without the cover fitted over the grinding wheel.

• Always fit the grinding wheel cover and tool rest tightly, and with the correct clearance.

• Never allow more than 1-1.5 mm clearance between tool rest and grinding wheel.

• Only use the grinding wheel for the work it was designed for (for example sharpening tools), and NOT for heavy construction work.

• The following information must be available, before you fit any new grinding wheel:

  • Details about the manufacturer.
  • Binding material.
  • Dimensions.
  • Permissible rotational speed.

• Never ream out the hole in a grinding wheel to a larger diameter.

• The maximum rotational speed of the grinding wheel should never be allowed to exceed the maximum speed given for the wheel.

• Never use any grinding wheel that is damaged or deformed.

• In order to be able to grind safely, the machine must be firmly bolted to a workbench.

• The tool rest should be replaced whenever the width of the tool rest measures less than 20 mm.

• The recommended depth of the recess in the flange (T) is 2 mm and the diameter of the spindle hole is 13 mm (see Fig. B ).

Whenever using the machine

• Check that the switch is NOT in the ‘ON/1’position before connecting the machine to the power supply.
• Always keep the power cord out of the way of the tool’s moving parts.

Immediately switch off the machine when:

• The plug or power cord is defective or damaged.
• The switch is defective.
• You smell smoke or burning insulation.

Electrical safety
When using electric machines always observe the safety regulations applicable in your country to reduce the risk of fire, electric shock and personal injury. Read the following safety instructions and also the enclosed safety instructions.

Always check that the power supply corresponds to the voltage on the rating plate.

Replacing cables or plugs
Immediately throw away old cables or plugs when they have been replaced by new ones. It is dangerous to insert the plug of a loose cable in the wall outlet.

Using extension cables
Only use an approved extension cable suitable for the power input of the machine. The minimum conductor size is 1.5 mm².When using a cable reel always unwind the reel completely.

Installation

The grinder must be firmly bolted to a workbench. The length of the fixing bolts will depend on the thickness of the workbench. If the workbench is made of steel, it is advisable to use a wooden block or plank between the grinder and the bench, to insulate it and prevent vibration.

Assembly and adjustment of spark guard bracket and spark guard.
Fig. B

The spark guard bracket and spark guard should only ever be assembled/adjusted with the grinding wheel stationary, and the machine disconnected from the power supply.

• Fix the spark guard bracket (4) with attached spark guard to the grinding wheel cover, using the screw provided (A).
• Set the spark guard bracket at the correct height. The clearance (B) between the wheel and the spark guard bracket should be 1 to 1.5 mm.
• Next tighten the screw (A) firmly.
• Position the spark guard to give maximum protection when working.
• Always wear safety glasses.

Fitting and adjusting tool rest

The tool rest should only be adjusted when the grinding wheel is completely stationary, and the machine is disconnected from the power supply (the wall socket).

• Fit the tool rest as shown in Fig. C.
• Fix it as tightly as possible in position, with a maximum clearance (C) of 1 to 1.5 mm between the tool rest and the grinding wheel.

Replacing the grinding wheel
Fig. C

Required tools:

• 19 mm spanner
• 8 mm spanner
• Screwdriver

Only ever replace the grinding wheel when the motor is at a standstill and the power is completely disconnected.

• Remove the grinding wheel guards using the tools listed above. The spindle nut on the right-hand side has a right-handed thread. The spindle nut on the left-hand side has a left-handed thread. Keep this in mind when you are replacing the grinding wheels.
• Loosen the nut using the correct spanner. Remove the old wheel from the spindle.
• Clean the flanges. Place one flange (A) back on the spindle, with the hollow side facing the grinding wheel. Slide the new wheel onto the spindle. Place the second flange (A) on the spindle, again with the hollow side facing the grinding wheel. Now tighten the nut on the spindle. Do not overtighten! Now refit the grinding wheel cover, and again adjust the tool rest correctly. Run the motor briefly, without grinding.

Operation

Selecting the grinding wheel
Coarse grinding wheels will in general remove the most material, and fine grinding wheels are used for finishing. If the surface is uneven, begin by using a coarse grinding wheel, and grind the work piece until it is smooth. Next use a fine grinding wheel to remove the grooves and scratching left by the coarse wheel, and finish off the work piece.

How to grind
To prevent the grinding surface from blocking up, avoid holding wood, lead or any other soft material or metal against the grinding wheel. To avoid creating grooves, do not press the work piece too firmly on the grinding wheel. Use water to regularly cool the work piece being ground. Wood chisels and the like should never be sharpened ‘blue’. Take care not to lose your grip on the object being ground, as it may suddenly become jammed between the tool rest and the grinding wheel. This can cause the stone to shatter, the motor to seize, or the work piece to fly off, all of which can cause injury and damage. Whenever the machine has been in use for 30 minutes, it should be switched off. Allow the machine to cool down to room temperature.

• Switching the machine on
• Check that the switch is in the “OFF/0” position before connecting the machine to the power supply.
• Press the power switch into the “ ON/1” position to start your bench grinder.
• Always keep the power cord out of the way of the tool’s moving parts.

Maintenance

Make sure that the machine is not live when carrying out maintenance work on the motor.

This machine has been designed to operate over a long period of time with a minimum of maintenance. Continuous satisfactory operation depends upon proper machine care and regular cleaning.

Troubleshooting

Should the machine fail to function correctly, a number of possible causes and the appropriate solutions are given below:

1. The electromotor becomes hot
   • The motor has become overloaded.
   • Give the motor a chance to cool down.
   • The motor is defect.
   • Please contact the service address on the warranty card.
2. Machine switched on, but will not run
   • Interruption in the mains connection.
   • Check mains connection for fracture.
   • The switch may be damaged.
   • Please contact the service address on the warranty card.

Repairs and servicing should only be carried out by a qualified technician or service firm.

Cleaning
Regularly clean the device’s casing with a soft cloth, preferably after each use. Keep the fan slits free of dust and dirt. Remove stubborn dirt using a soft cloth, dampened with soapy water. Do not use solvents such as benzene, alcohol, ammonia,  etc, which might damage the plastic parts.

Lubrication
The device does not need any additional lubrication.

Defects
If a defect appears due to a part wearing out, please contact the service center on the warranty card. At the end of these instructions there is an exhaustive overview of the parts that can be ordered.

Environment

To prevent damage during transport, the appliance is delivered in a solid packaging which consists largely of reusable material. Therefore please make use of options for recycling the packaging.

Damaged and/or disposed of electrical or electronic devices must be dropped off at recycling stations intended for that purpose.

Only for EC countries
Do not dispose of power tools into domestic waste. According to the European Guideline 2012/19/EU for Waste Electrical and Electronic Equipment and its implementation into national right, power tools that are no longer usable must be collected separately and disposed of in an environmentally friendly way.

Warranty

Read the warranty conditions on the separately supplied warranty card.

The product and the user manual are subject to change. Specifications can be changed without further notice.

Exploded view

Position

| Description|

No

---|---|---
206403| Switch| 1
206454| Tool support (right)| 2
101079| Protection glass (small)| 3
206408| Protection glass holder(right)| 4
206132| Protection glass holder (left)| 6
206405| Tool support (left)| 7
206143| Rubber foot| 8
BGA1055| Grinding stone 150x20x12,7mm|
BGA1056| Grinding stone 150x40x12,7mm|

DECLARATION OF CONFORMITY

**BGM1020 – BENCH GRINDER

**

We declare under our sole responsibility that this product is in conformity with directive 2011/65/EU of the European parliament and of the council of 8 June on the restriction of the use of certain hazardous substances in electrical and electronic equipment is in conformity and accordance with the following standards and regulations:

EN 62841-1, EN 62841-3-4, EN55014-1, EN55014-2,
EN61000-3-2, EN61000-3-3

2006/42/EC, 2014/30/EU, 2012/19/EU, 2011/65/EU

Zwolle, 01-02-2021

H.G.F. Rosberg CEO Ferm

References

• FERM Power Tools - Power to create

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>