PHILIPS IITBV1 2.4G Radio Module User Manual
- June 5, 2024
- Philips
Table of Contents
PHILIPS IITBV1 2.4G Radio Module
Product: IITBV1-ITS Module
Model: IITBV1
FCC ID: PQC-IITBV1
IC: 3549A-IITBV1
For OEM integration only device cannot be sold to general public. Therefore,
we will not supply a User’s manual.
We will ask OEM to include the following Notices required by FCC/ IC on the
product and in the User’s manual.
Notifications
FCC ID: PQC-IITBV1
IC: 3549A-IITBV1
NOTICE
Federal Communication Interference Statement (United States only)
This equipment has been tested and found to comply with the limits for a class
B digital device, pursuant to Part 15 of the FCC rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Re-orient or relocate the receiving antenna
- Increase the separation between the equipment and receiver
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected
- Consult the dealer or an experienced radio/TV technician for help
This device and its antenna(s) must not be co-located or operation in conjunction with any other antenna or transmitter.
Canadian Department of Communications Industry Canada Notice (Canada
only)
This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
FCC Rules, Part 15/ Industry Canada
This device complies with Part 15 of FCC Rules and Industry Canada licence-
exempt RSS standard(s).
Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference, including interference that may cause undesired operation of this device.
This equipment complies with FCC/IC radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency (RF) Exposure Guidelines in Supplement C to OET65 and RSS-102 of the IC radio frequency (RF) Exposure rules. This equipment should be installed and operated keeping the radiator at least 20cm or more away from person’s body (excluding extremities: hands, wrists, feet and ankles).
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.
This radio transmitter 3549A-IITBV1 has been approved by Industry Canada to
operate with the antenna types listed below with the maximum permissible gain
and required antenna impedance for each antenna type indicated. Antenna types
not included in this list, having a gain greater than the maximum gain
indicated for that type, are strictly prohibited for use with this device.
This device is going to be operated in 2400 MHz 2483 MHz frequency range, it
is restricted in indoor environment only. Frequency Tolerance+/-10ppm
WARNING:
The FCC / The Industry Canada regulations provide that changes or
modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
Manual and Product Labeling information
To The End User The end user manual shall include all required regulatory
information/warning as show in this manual.
When this module is installed in the host product, you must include a
“Contains FCC ID: PQCIITBV1” and “IC: 3549A-IITBV1” in the labeling of the
host product.
Philips Medizin Systeme Böblingen GmbH
Hewlett-Packard-Strasse 2, 71034 Böblingen, Germany, Tel +49(0)7031 463-0, Fax
+49(0)7031 463-2202
Geschäftsführer: Dr. Dieter Haase (Sprecher), Dr. Peter Ziese, Matthijs de
Groot
Registergericht Stuttgart Reg.-Nr. HRB 245187, Sitz der Gesellschaft:
Böblingen,
www.philips.com/healthcare
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>