Southern ENTERPRISES FA9620 Greenville 45.75 in. Touch Panel Electric Fireplace Instruction Manual

Southern ENTERPRISES FA9620 Greenville 45.75 in. Touch Panel Electric

Fireplace

ASSEMBLY

Techniques

Care & Safety

Package contents

Instuctions

Customer service

Product Number: FA5223

ELECTRICAL SPECIFICATIONS

• Voltage: 120V, 60 Hz
• Amps: 12.5 Amps
• Watts:  1500 Watts
• Lighting:  LED

Thank you for your purchase.

Electric Firebox Insert

Consumer safety information:
Please read this manual before installing and operating this appliance.

WARNING!!!
If the information in this manual is not followed correctly, an electric shock or fire may occur, resulting in property damage, personal injury, or loss of life. Do not store or use gasoline or other flammable vapors or liquids near this appliance.

Safety Feature:
This unit has an internal thermal overload protector. When a temperature that may cause overheating is reached, the heater will automatically shut off. Operation can only resume when the unit is reset. (See instructions below)

To Reset Heater:
Unplug the heater and wait 10 minutes for the unit to cool down. After 10 minutes, plug in the heater again and follow the operating instructions described in this manual.

Important Operating and Safety Instructions:

CAUTION :
High temperatures! Keep draperies, electrical cords, and other furnishings at least 3 feet (.9 meters) from the front and away from the front, sides, and rear of the heater.

WARNING :
Risk of fire – keep combustible material away from the front of the electrical fireplace. Servicing should be done only while the electrical fireplace is disconnected from the power supply.

Important Operating and Safety Information:

When using electrical appliances, the following basic precautions should always be followed to reduce the risk of fire, electric shock, and injury.

• Read all instructions before using this heater.
• Use this heater only as described in this manual. Any other use not recommended by the manufacturer may cause fire, electric shock, or injury.
• Before connecting the appliance to the electric source, check that the current and power match those given on the ratings plate.
• This heater is for use with a 120 Volt electrical outlet. The cord has a three-prong grounded plug, which must be used in a properly grounded three-prong outlet.
• Avoid the use of an extension cord since the extension cord may overheat and cause a risk of fire. However, if you must use an extension cord it must be a grounded No. 16 AWG minimum size and rated for no less than 1875 watts.
• Do not run the cord under carpet. Do not cover cord with throw rug, runner, or similar items. Cord should be placed away from traffic areas to prevent tripping hazard.
• Never use the cord to pull the appliance.
• Never leave the appliance unattended while it is in use.
• Turn controls to “off” before removing plug from outlet.
• Always unplug heater when not in use.
• Do not use outdoors.
• Only use heater on even and stable surface to prevent the appliance from tipping over.
• To prevent possible fire, do not block air intakes or exhaust in any manner. Do not use on soft surfaces, such as a bed, where openings may be blocked.
• Do not use in rooms in which highly flammable materials such as gas, paints, gasoline, solvents, etc. are stored.
• Keep minimum distance of 3 feet between the heater and curtains and other flammable materials.
• Do not place the appliance or the plug in water or any other liquid. Should the appliance accidentally fall into water, unplug the appliance immediately and have it checked by a qualified person before using it again.
• Do not use the appliance with wet hands, on a damp floor, or when the appliance itself is wet.
• The appliance must not be used if the glass is damaged.
• Do not operate any heater with a damaged cord or plug, after the heater malfunctions or has been dropped or damaged.
• The warm air vent becomes very hot during operation—do not touch. During operation, only touch the appliance’s switches and handles.
• The appliance should not be moved when hot. Never touch the hot parts with your bare skin.
• Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an electric shock or fire, or damage to the heater.
• Please turn off the unit manually when leaving/not in use for extended period.
• Please turn off the unit manually when the power goes out.
• Please BEWARE that the plug may become hot.
• It’s highly recommended to plug the unit to outlet with GFR/GFCI receptacle.
  SAVE THESE INSTRUCTIONS.

Maintenance:

1. Cleaning your fireplace:
   You may clean exterior of unit with a soft, damp, lint-free cloth.
   WARNING : Before cleaning the exterior of the appliance, disconnect the unit from the power supply. Clean unit only after it is cool to the touch.

2. Cleaning the front glass:
   The front glass panel may become dirty or dusty. Dust can be removed by lightly rubbing the glass surface with a clean, lint-free cloth or paper towel. To remove fingerprints or other marks, use a soft, damp, lintfree cloth with a household glass cleaner.

Helpful Advice for Installing Firebox into Mantel:

1. These instructions are provided in an easy to follow format. Simply follow the instructions to properly install unit.
2. Please retain all packaging until you have checked that there is no damage and your unit is working properly.
3. Small parts should be kept away from young children.
4. The area around the unit should be kept free of animal hair, lint, and other extraneous material that may be drawn into the workings of the appliance and could affect its performance.

Positioning/Locating Your Electric Fireplace:
When choosing a location for your new fireplace, ensure that the general instructions are properly followed. For best result, install the fireplace out of direct sunlight

Installation Instructions:

Once the location has been prepared, the fireplace insert can be installed.

1. Make sure the unit is turned off (refer to the operating instructions).
2. Place the fireplace insert on the floor, directly behind your mantel. Make sure the backs of both the mantel and the fireplace are facing you.
3. It is advisable to have 2 people place the fireplace insert into the mantel, as it is heavy. Gently slide it into the opening in the mantel until the flange is flush against the inside of the fireplace. Make sure the insert is centered left and right in the opening. Be careful when placing and adjusting the insert, as the bottom of the insert could scratch the finish of the wood base/hearth of your fireplace.
4. Attach the mounting brackets (found in the fireplace mantel box) with the supplied screws using a Phillips head screwdriver. DO NOT OVER TIGHTEN.
5. With the help of an assistant, carefully lift completed unit and place it with the front facing out in the final location you have chosen for your fireplace.

Operating Instructions:

Control Panel on the Front of Unit:

1. On/Off Main Power Button
   a. Press to switch the unit ON/OFF.
   b. Child Lock: turn the unit on and hold POWER button for at least 5 seconds until you hear a beep sound (and the log blinks) to enter the Child Lock mode. To turn off the Child Lock mode, please press and hold the POWER button again for at least 5 seconds until you hear the beep sound (and the log blinks).

2. Adjustable Flame Brightness
   Adjust the flame brightness level: F5 – F4 – F3 – F2 – F1 – OFF (F5 being the brightest and F1 the dimmest. F5 is the default).

3. On/Off Heater Button
   a. Program the thermostat. The fireplace can be used without the heater if desired.
   b. Adjust the temperature rating from 62°F – 82°F – ON (17°C – 27°C).
   Note : °F is the default unit. To change from Fahrenheit to Celsius: Hold the heater button for approximately 5 seconds. The temperature readout will switch directly from °F to °C and vice versa.

4. Adjustable Down Light Color
   Adjust the Down Light Color: d0 – d1 – d2 – d3 – d4 (d0:OFF, d1:Red, d2:Orange, d3:Blue, d4:White).

5. Adjustable Log Brightness
   Adjust the log brightness level: L5 – L4 – L3 – L2 – L1 – OFF (L5 being the brightest and L1 the dimmest. L5 is the default).

6. Adjustable Timer
   Control the duration of the heater function. Press the timer button until you have reached the desired duration time.
   Levels : 30 min – 1H – 2H – 3H – 4H – 5H – 6H – 7H – 8H – 9H – OFF.

ELECTRICAL CONNECTION:

A 12.5 AMP, 120 Volts, 60 Hz circuit with a properly grounded outlet is required. It is recommended that the fireplace be on a dedicated circuit, as other appliances on the same circuit may cause the circuit breaker to trip or blow the fuse when the heater is in operation.

ELECTRICAL SPECIFICATIONS

• Voltage: 120 VAC, 60 Hz
• Amps: 12.5 Amps
• Watts: 1500 Watts
• Lighting: LED

Remote Control Operating Procedures:

1. Power:
   Press to turn the unit ON/OFF

2. Flame:
   Press to adjust the level of brightness of the flame: F5- F4- F3- F2- F1- OFF. (F5 being the brightest and F1 the dimmest)
   up : raise the level of flame brightness
   down : lower the level of flame brightness

3. Timer:
   Press to adjust the duration of the heater: 30 min- 1H- 2H- 3H- 4H- 5H- 6H- 7H- 8H- 9H- OFF

4. Down Light:
   Press to adjust the Down Light Color: d0 – d1 – d2 – d3 – d4 (d0:OFF, d1:Red, d2:Orange, d3:Blue, d4:White).

5. Log:
   Press to adjust the level of brightness of the log: L5- L4- L3- L2- L1- OFF. (L5 being the brightest and L1 the dimmest)
   up : raise the level of log brightness
   down : lower the level of log brightness

6. Heater:
   Press to turn the heater ON/OFF. Adjust the temperature rating as follows: 62°F — 82 °F (17 °C — 27 °C) Note: ℉ is the default unit.
   up : raise the temperature rating
   down : lower the temperature rating
   Note : Do not mix old and new batteries.
   Do not mix alkaline, standard (carbon-Zinc) or rechargeable (nickel-cadium) batteries.

Self Regulating Heater
The heater will turn on when temperature is set higher than the room’s temperature and it will automatically turn off when the room has reached the desired temperature.

GROUNDING INSTRUCTIONS

This product must be grounded. If it should malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This product is equipped with a cord that has an equipment-grounding conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances. This heater is for use on 120 volts circuit and has a grounded plug that looks like the one illustrated on Figure.

1. See Figure 1 for grounding instruction. An adapter as shown at C is available for connecting three-blade grounding type plugs to two-slot receptacles. The green grounding plug extending from the adapter must be connected to a permanent ground such as a properly grounded outlet box. The adapter should not be used if a three-slot grounded receptacle is available.

Improper connection of the equipment grounding conductor can result in a risk of electric shock. Check with qualified electrician or serviceman if you are in doubt as to whether the product is properly grounded. Do not modify the plug provided with the product

• If it will not fit the outlet; have a proper outlet installed by qualified electrician.

FCC STATEMENT

NOTE : This equipment has been tested and found to comply with the limits for Class B digital device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio or television reception. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

• This device may not cause harmful interference, and
• This device must accept any interference received, including interference that may cause undesired operation. Modifications not approved by the party responsible for compliance could void user’s authority to operate the equipment. This Class B digital apparatus complies with Canadian ICES-003.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>