cecotec 05613 Breezecare 4000 Connected Humidifier Instruction Manual
- June 3, 2024
- cecotec
Table of Contents
cecotec 05613 Breezecare 4000 Connected Humidifier
SAFETY INSTRUCTIONS
- Read these instructions thoroughly before using the appliance. Keep this instruction manual for future reference or new users.
- Make sure that the mains voltage matches the voltage stated on the rating label of the appliance and that the wall outlet is grounded.
- This product is intended for household and indoor use, not commercial.
- Never use this device in a room where aerosol products (sprays) are used or in a room or where oxygen is being administered. Do not leave the product unsupervised during operation. Always unplug the product from the electrical outlet when it is not use.
- Place the product on a flat, steady, stable, heat-resistant surface.
- Do not use the device in areas where gasoline, paint, or flammable liquids are used or stored, as there may be a risk of fire or explosion.
- Do not cover the device with clothes, towels or any other object.
- Do not shake the device.
- Do not pour hot water into the device.
- When moving the humidifier, lift it by the base humidifier and not by the water tank.
- Do not use the device in rooms where there is already enough humidity.
- Do not touch water or components while the device is operating. Check the power cord regularly for visible damage. If the cord is damaged, it must be replaced by the official Technical Support
- Service of Cecotec in order to avoid any type of danger.
- Use the product in a well-ventilated area.
- Do not place the appliance close to heat sources, flammable substances, wet surfaces where it can fall or be pushed into water or allow it to come into contact with water or other liquids.
- To prevent a possible fire, do not block air intake or exhaust in any manner. Do not use on soft surface, such as a bed, where air outlet may become blocked.
- Wipe the air openings clean if they become clogged.
- To disconnect it, pull directly on the plug; do not pull on the power cord.
- Do not share the socket with other high-power appliances. Do not immerse the cord, plug, or any non-removable part of the appliance in water or any other liquid, nor expose the electrical connections to water. Do not handle the element with bare or wet hands.
- Disconnect the device from the power supply when not in use and before cleaning.
- To reduce the risk of electric shock, do not remove screws. The humidifier does not contain any user-serviceable parts. Avoid exposure to direct sunlight and always keep it away from walls and heat sources such as stoves, radiators, etc.
- Do not insert or allow objects to enter any ventilation or exhausted opening as this may cause an electric shock, fire or product damage.
- The device must be placed so that the plug is accessible. Keep the packaging materials out of the reach of children, they could be dangerous.
- The appliance is not intended to be used by children under the age of 8. It can be used by children over the age of 8, as long as they are given continuous supervision.
- This appliance can be used by children aged 8 and above, and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge, as long as they have been given supervision or instruction concerning the use of the appliance in a safe way and understand the hazards involved. Do not allow children to play with the appliance.
- Supervise children, they shall not play with the appliance. Close supervision is necessary when the appliance is being used by or near children.
PARTS AND COMPONENTS
- Steam outlet
- Display
- On/off button
- Warm mist button (Plasma function)
- Speed button
- Timer
- Humidity button
- Light
- Water tank
BEFORE USE
- Take the product out of the box.
- Remove all packaging material and save the original box.
- Make sure all parts and components are included and in good conditions.
- If any visible signs of damage are observed, contact the Technical Support Service immediately.
OPERATION
Note: The ideal relative humidity level for human comfort is between 45 % and 65 %. Excess humidity shows up in the form of condensation on cold surfaces or cold walls in the room. To measure the room’s humidity correctly, use a hygrometer.
- Relative humidity in different environments suitable for people:
- Bedroom, living room: 45-65 % RH
- Patient’s room: 40-55 % RH
- Room with computer, experiment equipment: 45-60 % RH
- Room with piano: 40-60 % RH
- Museum, exhibition hall, and library: 40-50 % RH
- Place the device on a flat surface.
Filling the water tank
Remove the device’s top cover and remove the water tank with the handle. Turn it upside down on a flat and dry surface. Disassemble the nut by turning it anticlockwise. Fill the tank with the desired level of water and close the tank again with the nut, turning it clockwise. Use the handle to assemble the water tank back on the product.
- Plug the device to a power supply. The display will light up and the device will beep. After 1 second, the display will turn off and the device will enter standby mode.
- Press on/off, the device will start working under mist mode at level 2. The blue light indicator will turn on. The control panel will display the current humidity.
Mist speed
- While the display shows current humidity, press the Max./Min. button to check the current mist speed. Press repeatedly to set the desired speed. There are 3 different settings.
Constant humidity
- When the LED display is showing current humidity, press the Humidity symbol.
- The humidity level can be set from 30 % RH to 90 % RH.
- Every time the symbol is pressed, it will be increased by 5 %.
- When it reaches 90 %, press again and the display will show “Co”. Do not operate the device for 3 seconds to cancel the humidity setting function.
- Note: If the target humidity is higher than the current humidity, the humidification function will work.
- When the target humidity is lower than the current humidity, the device will enter standby mode.
- Note: The mist speed cannot be adjusted under constant humidity function.
- During operation, hold down the humidity symbol for 2 seconds to turn the blue light indicator and the display on. Touch the symbol again to turn it off. After 15 seconds of no operation, the light indicators and display will turn off.
Timer
- There are 12 timer settings: 1, 2, 3, 4, 5, 6, 7, 8, 9, 10,11, 12 hours.
- Press the Timer symbol repeatedly to select the desired operating time.
- Press the Timer symbol until “– –” is displayed or hold down the Timer symbol twice to cancel the timer.
- Once the timer is set, do not touch any button and setting will be automatically saved after 5 seconds. After 1 minute, the display will show the current humidity.
- The display will show the remaining time every hour.
Warm water mist
- Press the Warm mist button to turn the warm mist function on and off. The warm mist function indicator will light up.
- Note: This function is not available when there is no water in the tank or when it is running under a non-humidifying mode.
- Auto shut-off system
- When the tank runs out of water, the device will automatically stop operating. The empty water indicator will turn on.
- Refill the water tank, and the device will continue operating with the previous settings. If the tank is not refilled, the device will turn off after 15 minutes.
- Touch the light symbol to choose between the 3 different levels of blue light intensity. Tap 4 times to turn it off.
- The device keeps the Wi-Fi connection activated during operation. To connect it, follow the instructions on the App manual section.
- In order to link your product with our App, please follow the below steps.
- Download the BreezeCare App from Google Play or App Store.
- If it is the first time you use it, register an account. If not, log in.
- Once you have entered the App, press “+” on the top right-hand corner and tap “Breeze Care”. Turn your device on and hold down the power button for 5 seconds until the device beeps. Check that the Wi-Fi icon is blinking.
- Enter your Wi-Fi password and press confirm.
- Then, the linking process will start automatically.
Warnings:
- Never run the humidifier when there is no water in water the tank and water basin.
- Do not pour any liquid other than clean water into the water tank or water base.
CLEANING AND MAINTENANCE
- Use a soft, damp cloth to clean the surface of the device.
- Do not use detergent, scouring pads, chemically treated cloths, gasoline, benzene, alcohol, thinner, or other solvents, as these can scratch and damage the tank and cause water leakage.
- Do not immerse the product in water or any other liquid.
- If scale is built up due to the use of hard water, it is recommended to:
- Use cold boiled water or distilled water.
- Clean the transducer, water tank and basin humidifier every week.
- Change the water in water tank more often to keep it fresh.
- Make sure to pour out water from the water tank and dry the water basin before you store it unused for a long time.
- Clean the whole humidifier and make sure that all parts of the humidifier are dried completely
- if it is supposed to be leaved unused for a long time.
Cleaning the transducer
- Clean with clean water or citric acid if there is scale in it.
- Brush off the scale from the surface.
- Rinse the transducer with clean water.
- Cleaning the humidifier basin
- Clean the water basin with soft cloth or use citric acid if there is scale in it.
- If there is scale covering the security switch, drop citric acid for 2-5 mins on the scale and clean it out with the brush.
- Rinse the water basin with clean water.
TROUBLESHOOTING
| Trouble | Possible cause | Solution |
|---|
The light indicator is off when switched on
| The humidifier is not plugged in.| Plug the humidifier into a powered
electrical socket.
Power cord is damaged.| Stop using the device immediately and contact the
Technical Support Service of Cecotec.
Humidifier is defective or malfunctioning.
The light indicators is on when switched on, but no mist comes out| Humidifier
is not turned on.| Press the power button to turn it on.
The target humidity is reached.| Increase the target humidity or change mode.
Water shortage indicator is on
| No water in the tank.| Refill the water tank and wait at least 1 minute.
Water level is low.
The water level required has not yet reached the vaporisation compartment.|
Wait at least 1 minute.
The water tank isn’t well positioned.| Check the positioning of tank on the
base.
The humidifier isn’t on a flat surface.| Check the positioning of the
humidifier.
The % RH of the room is over 90 %.|
Wait until the % RH gets lower.
Humidifier produces an unusual smell
|
Humidifier is new.
| Take out water tank, open cover, let it stay 12 hours in cool position.
---|---|---
Dirty water or water sitting too long.| Clean water tank, fill with clear
water.
Residual smell from diffusing aroma oil on the aroma cotton.| Remove the aroma
cotton, rinse it under clean water and allow it to dry.
Humidifier makes a loud or unusual sound
| Resonant in water tank when water is too low.|
Fill water into water tank.
Humidifier is on an unstable surface.| Move the humidifier to a stable flat surface.
Water tank is positioned incorrectly.
| Turn off and unplug the humidifier, then align the water tank cover with its respective opening in the inner chamber.
Humidifier is malfunctioning.
| Stop using the device immediately and contact the Technical Support Service of Cecotec.
The humidification capacity is too low
| There is natural or artificial air replacement in the room which interfere
the increase of %RH.| Check if doors and windows are closed.
Check if there is no air conditioning working in the room.
The air inlet grids and nozzle could be blocked.| Remove any blocking items
from the grids and the nozzle.
Too much scale in the water basin.|
Clean transducer.
The humidity selected rate is too low.| Increase mist output speed.
Increase humidity setting rate.
Water is too dirty or water kept too long in the tank.| Clean water tank,
change to fresh clear water.
The ambient humidity is too high
| Humidifier is working in Continuous mode.|
Change the mode.
---|---|---
The humidity target is too high.|
Select a lower %RH target.
Room is not well-ventilated
| Open a window to ensure proper air flow for the humidifier or move the
humidifier to a better ventilated room.
Excess water tank has spilled while filling the water tank or replacing the
water tank back onto the base.|
Wipe off excess water from the top and bottom of the base before replacing the water tank.
There is condensation in the room|
The room temperature is too low.
|
Heat the room up.
The mist suddenly stops coming out
| Programmed timer period has run out.|
Turn humidifier on.
The water shortage indicator is on.|
Refill water tank.
The target humidity level is reached.|
Incorrect humidity level is being displayed.
| Room is larger than the effective range of the humidifier.|
Move the humidifier to a room which is with suitable room size.
Moisture has built up inside of the humidity sensor.
| Turn off the humidifier and allow the humidity sensor to completely air dry
before resuming use.
The nozzle is facing the direction of the humidity sensor.|
Turn the nozzle so that it is facing away from the humidity sensor.
Humidity sensor is broken of defective.
| Stop using the device immediately and contact the Technical Support Service
of Cecotec.
Control panel does not work| Hands are too wet when operating control panel.|
Keep hands dry while operating the control panel.
---|---|---
Humidifier has malfunctioned.
| Stop using the device immediately and contact the Technical Support Service of Cecotec.
White dust appears around the humidifier
|
Water being used has a high mineral content.
| Use distilled water with the humidifier. If distilled water is not
available, use purified or filtered water. Remember to clean water tank at
least once a week.
Humidifier was not properly cleaned after last use.|
Clean humidifier.
Mist is coming out from the base
|
Water tank is not positioned correctly.
| Turn off and unplug the humidifier, then align the water tank cover with its
respective opening in the inner chamber.
Mist fog coming out from around nozzle| There are apertures between the nozzle
and water tank.| Reinstall the cover and check if the nozzle is well plugged
in the cover.
TECHNICAL SPECIFICATIONS
- Product reference: 05613
- Product: BreezeCare 4000 Connected
- 220-240V 50/60 Hz
- Power: 110 W
- Water tank capacity: 6L
DISPOSAL OF OLD ELECTRICAL APPLIANCES
The European directive 2012/19/EU on Waste Electrical and Electronic Equipment
(WEEE), specifies that old household electrical appliances must not be
disposed of with the normal unsorted municipal waste. Old appliances must be
collected separately, in order to optimize the recovery and recycling of the
materials they contain and reduce the impact on human health and the
environment. The crossed out “wheeled bin” symbol on the product reminds you
of your obligation to dispose of the appliance correctly. If the product has a
built-in battery or uses batteries, they should be removed from the appliance
and disposed of appropriately.
Consumers must contact their local authorities or retailer for information
concerning the correct disposal of old appliances and/or their batteries.
TECHNICAL SUPPORT AND WARRANTY
- This product is under warranty for 2 years from the date of purchase, as long as the proof of purchase is submitted, the product is in perfect physical condition, and it has been given proper use, as explained in this instruction manual.
- The warranty will not cover the following situations:
- The product has been used for purposes other than those intended for it, misused, beaten, exposed to moisture, immersed in liquid or corrosive substances, as well as any other fault attributable to the customer.
- The product has been disassembled, modified, or repaired by persons, not authorised by the official Technical Support Service of Cecotec.
- Faults deriving from the normal wear and tear of its parts, due to use.
- The warranty service covers every manufacturing defects of your appliance for 2 years, based on current legislation, except consumable parts. In the event of misuse, the warranty will not apply.
- If at any moment you detect any problem with your product or have any doubt, do not hesitate to contact Cecotec Technical Support Service at +34 963 210 728.
Grupo Cecotec Innovaciones S.L. C/ de la Pinadeta s/n, 46930 Quart de Poblet, Valencia (Spain) IC02200923
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>