Earda DM1WA Smart Dimmer Switch User Manual
- June 5, 2024
- Earda
Table of Contents
DM1WA Smart Dimmer Switch
User Manual
FEATURE
Product Introduction
- Excellent design and high-quality materials to ensure long-term stable and reliable semis to users
- Optimized dimming algorithms maximize the compatibility of lights and does not flicker at any brightness
- Wi-Fi connection has the most applicability, and has access to multiple platforms
- Stepless touch dimming makes the brightness adjustment easy and smooth
- Silent mechanical push button design provide the users best feedback
Specification
Installation
- Disconnect power by circuit breaker
- Check the line with voltage tester pen, make sure the power is off to prevent electric shock
- Follow the wiring instructions, connect the dimmer wires to each other leads and check for short circuits
- Screw the dimmer into the back box
- Mounting switch cover plate
- Connect circuit breaker restore power
Connection & Operation
- Once connect power correctly, the Green led on the bottom of dimmer will tum on, dimmer switch is ready to serve
- Push on/off button to turn on/off the light
- When the light is on, the user can touch the control panel adjust the brightness of the light, and the status indicator on the panel will change at the same time
- When the light is off, Green power led will on
Reset the product:
Press and hold ON/OFF button for 5 second then release, Green power indicator
will flash, dimmer get into setup mode, please follow setup instruction to
complete setup to start smart function
APP Operation
1. Scan QR code and download the app iOS or Android version
2. Register and login
The user needs to register the user first, and can use the mobile phone number
to register.
Once you are done, you can use this username to login to the APP and proceed
to the next step.
support some third-party accounts are directly logged in
3. Add Devices
After the user logs in, click the·+· icon in the upper right corner of the
main page to enter the add device interface, select the “Switch” menu and
click the switch device icon
To ensure that the ne-w dimmer power LED is flashing, select the Wi-Fi and enter the password then click OK.
4. Connect Devices
Wait system to search the device, connect and configure the device will take
sup to 3min.
Once the device configure successfully, please also input preferred name and
select location.
Remark
- Smart phone and device must connect to same Wi-Fi du ring setup mode
- The device must be added to the account before it can be controlled remotely
- After the device is successfully accessed, other users can obtain control of the product through the sharing function.
Troubleshooting
1. Can not connect to Wi-Fi router
a) Also make more you have good Wi-Fi signal strength at the location of the dimmer
b) Metal bon and metal surface- wall board may block M.S-Fi signal
c) Make sure input correct Wi-Fl password
d) The Dimmer only support 802.11 b/g/n 2.4GH. Wi-Fi signal, 5GHz NOT support
5. Control dimmer with APP
6. Add scene mode and timing mode in the APP
7. All added devices can be vie-wed in the main menu of the APP
FCC Caution
This device com plies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
§ 15.21 Information to user.
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
§ 15.105 Information to the user.
Note This equipment has been tested and found to comply with the limits fora Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference M a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can he determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with FCC radiation exposure limits set for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
IC Caution
This device complies with Industry Canada licence-exempt RSS standard (s).
Operation is subject to the following two conditions:
(l) This device may not cause interference, and
(2) This device must accept any interference, including interference that may cause undesired operation of the device.
This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>