Earda Technologies 1WAUS Smart Switch User Manual

Earda Technologies 1WAUS Smart Switch User Manual

Features

Product Introduction

• Excellent design and high-quality materials to ensure long- term stable and reliable service to users
• Wi-Fi connection has the most applicability, and has access to multiple platforms
• Silent mechanical push button design provide the user’s best feedback

Specification

Installation

1. Disconnect power by circuit breaker
2. Check the Line with voltage tester pen, make sure the power is off to prevent electric shock
3. Follow the wiring instructions, connect the dimmer wires to each other leads and check for short circuits
4. Screw the dimmer into the back box
5. Mounting switch cover plate
6. Connect circuit breaker restore power

Connection & Operation

1. Once connect power correctly, the Green led on the bottom of switch will turn on, switch is ready to serve
2. Push on/off button to turn on/off the light

Reset the product:

Press and hold ON/OFF button for 5 seconds then release, Green power indicator will flash, switch get into setup mode, please follow setup instruction to complete setup to start smart function

APP Operation

1. Register and log in
   The user needs to register by mobile phone number.
   After registration, you can use this username to log in the APP and proceed to the next step.

   • Support some third-party accounts log in directly .
     

2. Add Devices
   After the user login, click the“+”icon in the upper right corner of the main page to enter the add device interface, select the
   “Switch”menu and click the switch device icon
   

3. Add Devices
   To ensure that the new switch power LED is flashing, select the Wi-Fi and enter the password then click Next.
   

4. Add Devices
   Wait system to search the device, connect and configure the device will takes up to 3min.
   Once the device configure successfully, please also input preferred name and select location.
   
   Remark:

5. Smart phone and device must connect to same Wi-Fi during setup mode

6. The device must be added to the account before it can be controlled remotely

7. After the device is successfully accessed, other users can obtain control of the product through the sharing function.
   Troubleshooting

8. Can not connect to Wi-Fi router
   a) Also make sure you have good Wi-Fi signal strength at the location of the switch
   b) Metal box and metal surface – wall board may block Wi-Fi signal
   c) Make sure input correct Wi-Fi password
   d) The switch only support 802.11 b/g/n 2.4GHz Wi-Fi signal, 5GHz NOT support

9. Control switch with APP
   

10. Add timer mode in the APP
    

11. All added devices can be viewed in the main menu of the APP
    

FCC Caution.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

• 15.21 Information to user.

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

• 15.105 Information to the user.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator and your body.

ISED Statement

This device complies with Industry Canada license‐exempt RSS standard(s).
Operation is subject to the following two conditions:

1. This device may not cause interference, and
2. This device must accept any interference, including interference that may cause undesired operation of the device.

The digital apparatus complies with Canadian CAN ICES‐3 (B)/NMB‐3(B)

This device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 and compliance with RSS 102 RF exposure, users can obtain Canadian information on RF exposure and compliance.

This equipment complies with Canada radiation exposure limits set forth for an uncontrolled environment.

This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>