HIKVISION UD20554B Network PTZ Camera User Guide

: June 5, 2024
: Hikvision

Table of Contents

FCC Information
Safety Instructions
Electrical Safety
Documents / Resources

Network PTZ Camera
Quick Start Guide

Installation Video

http://enpinfodata.hikvision.com/analysisQR/showQR/2f824a34

|
---|---
**C**
|
|
|

http://enpinfodata.hikvision.com/analysisQR/showQR/902c0519

|

http://enpinfodata.hikvision.com/analysisQR/showQR/d983b5d2

Product appearance is for reference only and may differ from the actual product.
Cable Description (Page 2 – A)
Notes:
The cables vary depending on different camera models.

Power Cord: Supports 12 VDC power supply.
Video Cable: Connect BNC Cable to test the video output.
RS-485
Alarm Cable: Connect terminal ALARM-IN with GND interface, and connect terminal
ALARM-OUT with ALARM-COM interface.
Audio Cable: Connect terminal AUDIO-IN with GND interface.
Network Cable: Connect the network interface with a network cable.

Install the Memory Card (Page 2 – B)
Install the Camera (Page 3 – C)

C1. Pull the bracket ① out from the side of the camera, and unclench the decorative cover ②.
C2. Route the cables through the wall (and the hole in the bracket) or on the wall surface (and through the cable slot ③).
C3. Fix the bracket to the wall with four PA4×25 screws (supplied).
C4. Fix the camera to the bracket.
C5. Connect the cables, put them in the backbox ④, and close the decorative cover.

Waterproof for Outdoor Installation
(Page 5 – D)

Install network cable waterproof jacket.
Use supplied waterproof tape to protect cable connectors and unused cables.

Alarm Output (Page 6 – E)
① Relay output
② DC load
③ Power supply
④ JQC-3FG Relay

Protective Measures for Outdoor
Installation (Page 6 – F1)

Activate and Access Network
Camera (Page 6 – F2)

About this Manual

The Manual includes instructions for using and managing the Product.
Pictures, charts, images, and all other information hereinafter are for description and explanation only.
The information contained in the Manual is subject to change, without notice, due to firmware updates or other reasons. Please find the latest version of this Manual at the
Hikvision website (https://www.hikvision.com/). Please use this Manual with the guidance and assistance of professionals trained in supporting the Product.
Trademarks
and other Hikvision trademarks and logos are the properties of Hikvision in various jurisdictions.
Other trademarks and logos mentioned are the properties of their respective owners.

DISCLAIMER CYBER-ATTACKS, HACKER ATTACKS, VIRUS INFECTIONS, OR OTHER INTERNET SECURITY RISKS;

HOWEVER, HIKVISION WILL PROVIDE TIMELY TECHNICAL SUPPORT IF REQUIRED.

YOU AGREE TO USE THIS PRODUCT IN COMPLIANCE WITH ALL APPLICABLE LAWS, AND YOU ARE SOLELY RESPONSIBLE FOR ENSURING THAT YOUR USE CONFORMS TO THE APPLICABLE LAW. ESPECIALLY, YOU ARE RESPONSIBLE, FOR USING THIS PRODUCT IN A MANNER THAT DOES NOT INFRINGE ON THE RIGHTS OF THIRD PARTIES, INCLUDING WITHOUT LIMITATION, RIGHTS OF PUBLICITY, INTELLECTUAL PROPERTY RIGHTS, OR DATA PROTECTION AND OTHER PRIVACY RIGHTS. YOU SHALL NOT USE THIS PRODUCT FOR ANY PROHIBITED END-USES, INCLUDING THE DEVELOPMENT OR PRODUCTION OF WEAPONS OF MASS DESTRUCTION, THE DEVELOPMENT OR PRODUCTION OF CHEMICAL OR BIOLOGICAL WEAPONS, ANY ACTIVITIES IN THE CONTEXT RELATED TO ANY NUCLEAR EXPLOSIVE OR UNSAFE NUCLEAR FUEL CYCLE, OR IN SUPPORT OF HUMAN RIGHTS ABUSES.

IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE LATTER PREVAILS.

Regulatory Information

FCC Information

Please take attention that changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

FCC compliance: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body.

FCC Conditions

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

This device may not cause harmful
This device must accept any interference received, including interference that may cause undesired operation.

EU Conformity Statement

This product and – if applicable – the supplied accessories too are marked with “CE” and comply therefore with the applicable harmonized European standards listed under the Low Voltage
Directive 2014/35/EU, the EMC
Directive 2014/30/EU, the RoHS
Directive 2011/65/EU, and RE
Directive 2014/53/EU.

2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union. For proper recycling, return this product to your local supplier upon the purchase of equivalent new equipment, or dispose of it at designated collection points. For more information, please see www.recyclethis.info.

2006/66/EC (battery directive): This product contains a battery that cannot be disposed of as unsorted municipal waste in the European Union. See the product documentation for specific battery information. The battery is marked with this symbol, which may include lettering to indicate cadmium (Cd), lead (Pb), or mercury (Hg). For proper recycling, return the battery to your supplier or to a designated collection point. For more information, please see www.recyclethis.info.

Industry Canada ICES-003 Compliance

This device meets the CAN ICES-3 (B)/N MB-3(B) standards requirements.
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:

this device may not cause interference, and
this device must accept any interference, including interference that may cause undesired operation of the device.

operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the
antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.

KC
Class B: This device is intended for mainly home use (Class B) and may be used in all areas.

Safety Instructions

Warnings
Laws and Regulations
The device should be used in compliance with local laws, electrical safety regulations, and fire prevention regulations.

Electrical Safety

CAUTION: To reduce the risk of fire, replace only with the same type and rating of the fuse.

Battery
This equipment is not suitable for use in locations where children are likely to be present.

CAUTION: Risk of explosion if the battery is replaced by an incorrect type.

Improper replacement of the battery with an incorrect type may defeat a safeguard (for example, in the case of some lithium battery types). Do not dispose of the battery in
a fire or a hot oven, or mechanically crush or cut the battery, which may result in an explosion.

Do not leave the battery at an extremely high temperature in the surrounding environment, which may result in an explosion or the leakage of flammable liquid or gas.

Do not subject the battery to extremely low air pressure, which may result in an explosion or the leakage of flammable liquid or gas.

Dispose of used batteries according
to the instructions.

Cautions
Fire Prevention

No naked flame sources, such as lighted candles, should be placed on the equipment.

The serial port of the equipment is used for debugging only.

Hot Surface
CAUTION: Hot parts! Burned fingers when handling the parts.

This sticker is to indicate that the marked item can be hot and should not be touched without taking care. Wait one-half hour after switching off before handling parts.

The device with this sticker is intended for installation in a restricted access location. Access can only be gained by service persons or by users who have been instructed about the reasons for the restrictions applied to the location and about any precautions that shall be taken.

Installation

Install the equipment according to the instructions in this manual.
To prevent injury, this equipment must be securely attached to the ceiling/wall in accordance with the installation instructions.
Be sure that there is enough space to install the device and accessories. Make sure that the wall is strong enough to withstand at least 8 times the weight of the device and the mount.
Make sure that the power has been disconnected before you wire, install, or disassemble the device.

Transportation
Keep the device in original or similar packaging while transporting it.
Do not drop the product or subject it to physical shock.

Power Supply
The power source should meet limited power source or PS2 requirements according to IEC 60950-1 or IEC 62368-1 standard.
Refer to the device label for the
standard power supply. Please make sure your power supply matches with your device.
Use a power adapter provided by qualified manufacturers. It is recommended to provide an independent power adapter for each device as adapter overload may cause overheating or a fire hazard.

System Security
Please understand that you have the responsibility to configure all the passwords and other security settings about the device, and keep your user name and password.

Maintenance
If the product does not work properly, please contact your dealer or the nearest service center. We shall not assume any responsibility for problems caused by unauthorized repair or maintenance.
A few device components (e.g., electrolytic capacitor) require regular replacement. The average lifespan varies, so periodic checking is recommended. Contact your dealer for details.

Cleaning
Please use a soft and dry cloth to clean the interior and exterior surfaces. Do not use alkaline detergents.

Using Environment
When any laser equipment is in use, make sure that the device lens is not exposed to the laser beam, or it may burn out.
Do not aim the lens at the sun or any other bright light.
To avoid heat accumulation, good ventilation is required for a proper operating environment.
DO NOT expose the device to extremely hot, cold, dusty, corrosive, saline- alkali, or damp environments. For temperature and humidity requirements, see device specification.
DO NOT expose the device to high electromagnetic radiation.

Illuminator
Make sure that there is no reflective surface too close to the device lens. The light from the device may reflect back into the lens causing reflection.

The beam of light at a distance of 200 mm is classified as Risk Group 1 (RG1). Possible hazardous optical radiation emitted from this product.
DO NOT stare at the operating light source. May be harmful to the eyes.

If appropriate shielding or eye protection is not available, turn on the light only at a safe distance or in the area that is not directly exposed to the light when installing or
maintaining the device.

Emergency
If smoke, odor, or noise arises from the device, immediately turn off the power, unplug the power cable, and contact the service center.

Time Synchronization

Set up device time manually for the first time access if the local time is not synchronized with that of the network. Visit the device via web browser/client software and go to
time settings interface.

5 052620201102

UD20554B-A

Documents / Resources

| HIKVISION UD20554B Network PTZ Camera [pdf] User Guide
DS2DE3AS6, 2ADTD-DS2DE3AS6, 2ADTDDS2DE3AS6, UD20554B Network PTZ Camera, UD20554B, Network PTZ Camera
---|---